scholarly journals An Optical Fiber Fabry–Perot Pressure Sensor with Optimized Thin Microbubble Film Shaping for Sensitivity Enhancement

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 358 ◽  
Author(s):  
Shubin Zhang ◽  
Zhenjun Shao ◽  
Jinrong Liu ◽  
Meixue Zong ◽  
Jian Shen ◽  
...  
Keyword(s):  
Thin Film ◽  
Arc Discharge ◽  
Structural Parameters ◽  
Silicon Film ◽  
Glass Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot ◽  
Micrometer Scale

A pressure-assisted arc discharge method of preparing silicon microbubbles with a glass tube was utilized for decreasing the bubble film’s thickness and improving the bubble’s uniformity. By controlling the arc discharge intensity, discharge time and the position of the fiber carefully, the thickness of the microbubble film was reduced to the micrometer scale. Later, the thin film of the microbubble was transferred to the end the single-mode-fiber/glass-tube structure, for forming the FP (Fabry–Perot) interference cavity. As the thin film is sensitive to the outer pressure, such a configuration could be used for a high-sensitive-pressure measurement. Experimental results show that the sensitivity of this FP (Fabry–Perot) cavity was 6790 pm/MPa when the outer pressure ranges from 100 to 1600 kPa, and the relationship between the structural parameters of the thin film and the outer pressure was theoretically analyzed. Moreover, this special structure made of the end silicon film microbubble is more suitable for high-sensitivity applications.

scholarly journals A Micro Bubble Structure Based Fabry–Perot Optical Fiber Strain Sensor with High Sensitivity and Low-Cost Characteristics

Sensors ◽  
2017 ◽  
Vol 17 (3) ◽  
pp. 555 ◽  
Author(s):  
Lu Yan ◽  
Zhiguo Gui ◽  
Guanjun Wang ◽  
Yongquan An ◽  
Jinyu Gu ◽  
...  
Keyword(s):  
Low Cost ◽  
Strain Sensor ◽  
Glass Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot ◽  
Micro Bubble ◽  
Bubble Structure ◽  
Cost Characteristics

A high-sensitivity, low-cost, ultrathin, hollow fiber micro bubble structure was proposed; such a bubble can be used to develop a high-sensitivity strain sensor based on a Fabry–Perot interferometer (FPI). The micro bubble is fabricated at the fiber tip by splicing a glass tube to a single mode fiber (SMF) and then the glass tube is filled with gas in order to expand and form a micro bubble. The sensitivity of the strain sensor with a cavity length of about 155 μm and a bubble wall thickness of about 6 μm was measured to be up to 8.14 pm/μϵ.

scholarly journals Cascaded-Cavity Fabry-Perot Interferometric Gas Pressure Sensor based on Vernier Effect

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3677 ◽  
Author(s):  
Peng Chen ◽  
Yutang Dai ◽  
Dongsheng Zhang ◽  
Xiaoyan Wen ◽  
Minghong Yang
Keyword(s):  
Capillary Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Gas Pressure ◽  
Glass Capillary ◽  
Compact Structure ◽  
Fabry Perot ◽  
Fs Laser ◽  
Vernier Effect

An extrinsic Fabry-Perot interferometer (EFPI) composed of double fiber FP cavities in a glass capillary tube to generate Vernier effect has been fabricated and employed for gas pressure sensing. A lead-in single-mode fiber (LSMF) and a reflective single-mode fiber (RSMF) were inserted into the capillary tube to form a FP cavity. Femtosecond (fs) laser was used to ablate openings on a capillary tube for gas passage to the FP cavity. A fusion hole was also drilled on the end face of a SMF by fs laser. The sensitivity of the sensor is enhanced due to Vernier effect. Experimental results show that the sensitivity was as high as 86.64 nm/MPa in the range of 0~0.6 MPa, which is 32.8 times larger than that of an open-cavity EFPI sensor without Vernier effect. The temperature cross-sensitivity of the sensor was measured to be about 5.18 KPa/°C. The proposed sensor was characterized by its high sensitivity, compact structure and ease of fabrication, and would have extensive application prospects in gas sensing fields.

scholarly journals A High Precision Fiber Optic Fabry–Perot Pressure Sensor Based on AB Epoxy Adhesive Film

Photonics ◽  
2021 ◽  
Vol 8 (12) ◽  
pp. 581
Author(s):  
Yanan Zhang ◽  
Shubin Zhang ◽  
Haitao Gao ◽  
Danping Xu ◽  
Zhuozhen Gao ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Epoxy Adhesive ◽  
Curing Time ◽  
Adhesive Film ◽  
Interference Spectrum ◽  
Fabry Perot ◽  
Potential Applications

This paper proposes a Fabry–Perot pressure sensor based on AB epoxy adhesive with ultra-high sensitivity under low pressure. Fabry–Perot interference, located between single-mode fiber (SMF) and hollow-core fiber (HCF), is an ultra-thin AB epoxy film formed by capillary action. Then the thick HCF was used to fix the HCF and SMF at both ends with AB epoxy adhesive. Experimental results show that when the thickness of AB epoxy film is 8.74 μm, and the cavity length is 30 μm, the sensor has the highest sensitivity. The sensitivity is 257.79 nm/MPa within the pressure range of 0–70 kPa. It also investigated the influence of the curing time of AB epoxy on the interference spectrum. Experiments showed that the interference spectrum peak is blue-shifted with the increase of curing time. Our study also demonstrated the humidity stability of this pressure sensor. These characteristics mean that our sensor has potential applications in the biomedical field and ocean exploration.

scholarly journals A High Sensitivity Temperature Sensing Probe Based on Microfiber Fabry-Perot Interference

Sensors ◽  
2019 ◽  
Vol 19 (8) ◽  
pp. 1819 ◽  
Author(s):  
Zhoubing Li ◽  
Yue Zhang ◽  
Chunqiao Ren ◽  
Zhengqi Sui ◽  
Jin Li
Keyword(s):  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Temperature Sensing ◽  
Compact Structure ◽  
Fabry Perot ◽  
Temperature Monitor ◽  
Core Fiber ◽  
Fitting In

In this paper, a miniature Fabry-Perot temperature probe was designed by using polydimethylsiloxane (PDMS) to encapsulate a microfiber in one cut of hollow core fiber (HCF). The microfiber tip and a common single mode fiber (SMF) end were used as the two reflectors of the Fabry-Perot interferometer. The temperature sensing performance was experimentally demonstrated with a sensitivity of 11.86 nm/°C and an excellent linear fitting in the range of 43–50 °C. This high sensitivity depends on the large thermal-expansion coefficient of PDMS. This temperature sensor can operate no higher than 200 °C limiting by the physicochemical properties of PDMS. The low cost, fast fabrication process, compact structure and outstanding resolution of less than 10−4 °C enable it being as a promising candidate for exploring the temperature monitor or controller with ultra-high sensitivity and precision.

Intrinsic fiber-optic Fabry–Perot interferometer based on arc discharge and single-mode fiber

2013 ◽  
Vol 52 (12) ◽  
pp. 2670 ◽  
Author(s):  
Di Wu ◽  
Tao Zhu ◽  
Guo-Yin Wang ◽  
Jian-Yu Fu ◽  
Xiao-Guang Lin ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Arc Discharge ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot

scholarly journals A Large-Area and Nanoscale Graphene Oxide Diaphragm-Based Extrinsic Fiber-Optic Fabry–Perot Acoustic Sensor Applied for Partial Discharge Detection in Air

Nanomaterials ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 2312
Author(s):  
Shuchao Wang ◽  
Weigen Chen
Keyword(s):  
Graphene Oxide ◽  
Fiber Optic ◽  
Partial Discharge ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Acoustic Sensor ◽  
Performance Tests ◽  
Large Area ◽  
Fabry Perot

This article presents an extrinsic fiber-optic acoustic sensor applied for partial discharge (PD) detection in air. A Fabry–Perot (F-P) cavity consisting of a single-mode fiber (SMF) and a graphene oxide (GO) film, whose thickness and effective vibration diameter are approximately 500 nm and 4.377 mm, respectively, is used as this sensing core, and the manufacturing process of GO diaphragms and this sensing probe is illustrated to be simple and controllable. Performance tests indicate that this proposed sensor maintains a linear acoustic-pressure response and a flat frequency response in the range of 200 Hz to 20 kHz, while being an omnidirectional sensor and having high working stability during a ten-day test period. Additionally, PD detection results show that the minimum PD size detected by this proposed sensor in air was approximately 100 pC, which demonstrates that this proposed sensor can achieve high-sensitivity PD detection in air.

scholarly journals Characterization of small-signal intensity modulation of single-mode fiber grating Fabry-Perot laser source

2012 ◽  
Vol 19 (2) ◽  
pp. 64-70 ◽  
Author(s):  
Hisham Kadhum Hisham ◽  
Ahmad Fauzi Abas ◽  
Ghafour Amouzad Mahdiraji ◽  
Mohd Adzir Mahdi ◽  
Ahmad Shukri Muhammad Noor
Keyword(s):  
Signal Intensity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Intensity Modulation ◽  
Laser Source ◽  
Fiber Grating ◽  
Small Signal ◽  
Fabry Perot

Fabrication, Characterization and Microsensing of Whispering-Gallery Mode Micro-Coupling Systems

2008 ◽  
Author(s):  
Qiulin Ma ◽  
Tobias Rossmann ◽  
Zhixiong Guo
Keyword(s):  
Transmission Loss ◽  
Coupling Efficiency ◽  
High Sensitivity ◽  
Single Mode ◽  
Whispering Gallery Mode ◽  
Single Mode Fiber ◽  
Whispering Gallery ◽  
Coupling System ◽  
Wide Range ◽  
Micro Sensor

An optical micro-coupling system of whispering-gallery mode usually consists of a resonator (e.g. a sphere) and a coupler (e.g. a taper). In this report, silica microspheres of 50–500 μm in diameter are fabricated by hydrogen flame fusing of an end of a single mode fiber or fiber taper. Fiber tapers are fabricated by the method of heating and pulling that meets an adiabatic condition. Taper’s waist diameter can routinely be made less than 1 μm and almost zero transmission loss in a taper is achieved which allows an effective and phase-matched coupling for a wide range sizes of microspheres. Both resonators and couplers’ surface microstructure and shapes are examined by scanning electronic microscopy. Three regimes of coupling are achieved, enabling a good flexibility to control Q value and coupling efficiency of a micro-coupling system. Whispering gallery mode shift is used to demonstrate a novel temperature micro-sensor. Its sensitivity determined from actual experimental results agrees well with the theoretical value. A concept of using the photon’s cavity ring down (CRD) in the microsphere to make a novel high-sensitivity trace gas micro-sensor is proposed. The CRD time constant when ammonia is chosen as the analyte gas is predicted using the simulated absorption lines.

Sign in / Sign up

Export Citation Format

Share Document