scholarly journals A Novel Approach on the Unipolar Axial Type Eddy Current Brake Model Considering the Skin Effect

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1561
Author(s):  
Hery Tri Waloyo ◽  
U Ubaidillah ◽  
Dominicus Danardono Dwi Prija Tjahjana ◽  
Muhammad Nizam ◽  
Muhammad Aziz
Keyword(s):  
Correction Factor ◽  
Eddy Current ◽  
High Speed ◽  
Skin Effect ◽  
Actual Condition ◽  
Average Error ◽  
Low Speed ◽  
Novel Approach ◽  
Calculation Results ◽  
Braking Torque

The braking torque mathematical modelling in electromagnetic eddy current brake (ECB) often ignores the skin effect that occurrs during operation. However this phenomenon can not be simply neglected. Therefore, this paper presents a mathematical model of braking torque for a unipolar axial type of ECB system with a non-magnetic disk, which considers the skin effects. The use of mathematical models that consider the existence of skin effects is significant in approaching the braking torque according to the actual condition. The utilization of generic calculations to the model of the ECB braking torque leads to invalid results. Hence, in this paper, the correction factor was added to improve the braking torque calculation as a comparator to the proposed equation. However, the modification and addition of the correction factor were only valid to estimate the low-speed regimes of torque, but very distant for the high-speed condition. From the comparison of calculated values using analytical and 3D modelling, the amount of braking torque at a low speed was found to have an average error for the equation using a correction factor of 1.78 Nm, while after repairing, a value of 1.16 Nm was obtained. For the overall speed, an average error of 14.63 Nm was achieved, while the proposed equation had a small difference of 1.79 Nm. The torque difference from the calculation results of the proposed model with the measurement value in the experiment was 4.9%. Therefore, it can be concluded that the proposed equation provided a better braking torque value approach for both low and high speeds.

Performance analysis of magnetic gear with Halbach array for high power and high speed

2020 ◽  
Vol 64 (1-4) ◽  
pp. 959-967
Author(s):  
Se-Yeong Kim ◽  
Tae-Woo Lee ◽  
Yon-Do Chun ◽  
Do-Kwan Hong
Keyword(s):  
Permanent Magnet ◽  
Eddy Current ◽  
High Power ◽  
High Speed ◽  
Torque Ripple ◽  
Eddy Current Loss ◽  
Element Analysis ◽  
Current Loss ◽  
Halbach Array ◽  
Magnetic Gear

In this study, we propose a non-contact 80 kW, 60,000 rpm coaxial magnetic gear (CMG) model for high speed and high power applications. Two models with the same power but different radial and axial sizes were optimized using response surface methodology. Both models employed a Halbach array to increase torque. Also, an edge fillet was applied to the radial magnetized permanent magnet to reduce torque ripple, and an axial gap was applied to the permanent magnet with a radial gap to reduce eddy current loss. The models were analyzed using 2-D and 3-D finite element analysis. The torque, torque ripple and eddy current loss were compared in both models according to the materials used, including Sm2Co17, NdFeBs (N42SH, N48SH). Also, the structural stability of the pole piece structure was investigated by forced vibration analysis. Critical speed results from rotordynamics analysis are also presented.

Do You Name Speedy Objects Faster Than Slow Objects: SPEEDED NAMING OR NAMING SPEED? THE AUTOMATIC EFFECT OF OBJECT SPEED ON PERFORMANCE

2018 ◽  
Author(s):  
Moshe Shay Ben-Haim ◽  
Eran Chajut ◽  
Ran Hassin ◽  
Daniel Algom
Keyword(s):  
High Speed ◽  
Mental Representations ◽  
Reading Aloud ◽  
Naming Task ◽  
Naming Speed ◽  
Low Speed ◽  
Everyday Objects ◽  
Pictures And Words

we test the hypothesis that naming an object depicted in a picture, and reading aloud an object’s name, are affected by the object’s speed. We contend that the mental representations of everyday objects and situations include their speed, and that the latter influences behavior in instantaneous and systematic ways. An important corollary is that high-speed objects are named faster than low-speed objects despite the fact that object speed is irrelevant to the naming task at hand. The results of a series of 7 studies with pictures and words support these predictions.

scholarly journals Splatters and Aerosols Contamination in Dental Aerosol Generating Procedures

2021 ◽  
Vol 11 (4) ◽  
pp. 1914
Author(s):  
Pingping Han ◽  
Honghui Li ◽  
Laurence J. Walsh ◽  
Sašo Ivanovski
Keyword(s):  
Particle Size ◽  
Disease Transmission ◽  
High Speed ◽  
Low Speed ◽  
Dental Procedures ◽  
Dental Equipment ◽  
Produce Contamination ◽  
Fluorescein Dye ◽  
Filter Papers ◽  
Airborne Disease

Dental aerosol-generating procedures produce a large amount of splatters and aerosols that create a major concern for airborne disease transmission, such as COVID-19. This study established a method to visualise splatter and aerosol contamination by common dental instrumentation, namely ultrasonic scaling, air-water spray, high-speed and low-speed handpieces. Mock dental procedures were performed on a mannequin model, containing teeth in a typodont and a phantom head, using irrigation water containing fluorescein dye as a tracer. Filter papers were placed in 10 different locations to collect splatters and aerosols, at distances ranging from 20 to 120 cm from the source. All four types of dental equipment produced contamination from splatters and aerosols. At 120 cm away from the source, the high-speed handpiece generated the greatest amount and size (656 ± 551 μm) of splatter particles, while the triplex syringe generated the largest amount of aerosols (particle size: 1.73 ± 2.23 μm). Of note, the low-speed handpiece produced the least amount and size (260 ± 142 μm) of splatter particles and the least amount of aerosols (particle size: 4.47 ± 5.92 μm) at 120 cm. All four dental AGPs produce contamination from droplets and aerosols, with different patterns of distribution. This simple model provides a method to test various preventive strategies to reduce risks from splatter and aerosols.

scholarly journals Three-Axis Inductive Displacement Sensor Using Phase-Sensitive Digital Signal Processing for Industrial Magnetic Bearing Applications

Actuators ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 115
Author(s):  
Teemu Sillanpää ◽  
Alexander Smirnov ◽  
Pekko Jaatinen ◽  
Jouni Vuojolainen ◽  
Niko Nevaranta ◽  
...  
Keyword(s):  
Signal Processing ◽  
Digital Signal Processing ◽  
Eddy Current ◽  
High Speed ◽  
Digital Signal ◽  
Magnetic Bearing ◽  
Air Gap ◽  
Sensor Design ◽  
Quadrature Demodulation ◽  
Displacement Sensors

Non-contact rotor position sensors are an essential part of control systems in magnetically suspended high-speed drives. In typical active magnetic bearing (AMB) levitated high-speed machine applications, the displacement of the rotor in the mechanical air gap is measured with commercially available eddy current-based displacement sensors. The aim of this paper is to propose a robust and compact three-dimensional position sensor that can measure the rotor displacement of an AMB system in both the radial and axial directions. The paper presents a sensor design utilizing only a single unified sensor stator and a single shared rotor mounted target piece surface to achieve the measurement of all three measurement axes. The sensor uses an inductive measuring principle to sense the air gap between the sensor stator and rotor piece, which makes it robust to surface variations of the sensing target. Combined with the sensor design, a state of the art fully digital signal processing chain utilizing synchronous in-phase and quadrature demodulation is presented. The feasibility of the proposed sensor design is verified in a closed-loop control application utilizing a 350-kW, 15,000-r/min high-speed industrial induction machine with magnetic bearing suspension. The inductive sensor provides an alternative solution to commercial eddy current displacement sensors. It meets the application requirements and has a robust construction utilizing conventional electrical steel lamination stacks and copper winding.

scholarly journals Tracking by Deblatting

2021 ◽  
Author(s):  
Denys Rozumnyi ◽  
Jan Kotera ◽  
Filip Šroubek ◽  
Jiří Matas
Keyword(s):  
High Speed ◽  
High Performance ◽  
Motion Blur ◽  
Velocity Estimation ◽  
High Speed Camera ◽  
Trajectory Function ◽  
Novel Approach ◽  
Blind Deblurring ◽  
Object Trajectories ◽  
Complex Trajectories

AbstractObjects moving at high speed along complex trajectories often appear in videos, especially videos of sports. Such objects travel a considerable distance during exposure time of a single frame, and therefore, their position in the frame is not well defined. They appear as semi-transparent streaks due to the motion blur and cannot be reliably tracked by general trackers. We propose a novel approach called Tracking by Deblatting based on the observation that motion blur is directly related to the intra-frame trajectory of an object. Blur is estimated by solving two intertwined inverse problems, blind deblurring and image matting, which we call deblatting. By postprocessing, non-causal Tracking by Deblatting estimates continuous, complete, and accurate object trajectories for the whole sequence. Tracked objects are precisely localized with higher temporal resolution than by conventional trackers. Energy minimization by dynamic programming is used to detect abrupt changes of motion, called bounces. High-order polynomials are then fitted to smooth trajectory segments between bounces. The output is a continuous trajectory function that assigns location for every real-valued time stamp from zero to the number of frames. The proposed algorithm was evaluated on a newly created dataset of videos from a high-speed camera using a novel Trajectory-IoU metric that generalizes the traditional Intersection over Union and measures the accuracy of the intra-frame trajectory. The proposed method outperforms the baselines both in recall and trajectory accuracy. Additionally, we show that from the trajectory function precise physical calculations are possible, such as radius, gravity, and sub-frame object velocity. Velocity estimation is compared to the high-speed camera measurements and radars. Results show high performance of the proposed method in terms of Trajectory-IoU, recall, and velocity estimation.

Dynamic Analysis of DVG 850 High-Speed Machining Center

2012 ◽  
Vol 487 ◽  
pp. 203-207
Author(s):  
Gong Xue Zhang ◽  
Xiao Kai Shen
Keyword(s):  
High Speed ◽  
Simulation Analysis ◽  
Response Analysis ◽  
Improved Method ◽  
Analysis Software ◽  
Element Analysis ◽  
Harmonic Response ◽  
Machining Center ◽  
Calculation Results ◽  
Harmonic Response Analysis

Purpose, with the application of workbench finite element analysis software, get the analysis results of DVG 850 high-speed vertical machining center via the modal analysis and harmonic response analysis. Use the calculation results for reference, put forward the improved method, and prove the credibility of the simulation analysis by testing DVG 850 prototype.

Sign in / Sign up

Export Citation Format

Share Document