scholarly journals Numerical Characterization of Corona Spark Plugs and Its Effects on Radicals Production

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 381
Author(s):  
Giorgio La Civita ◽  
Francesco Orlandi ◽  
Valerio Mariani ◽  
Giulio Cazzoli ◽  
Emanuele Ghedini
Keyword(s):  
Steady State ◽  
Transport Model ◽  
Thermal Dissociation ◽  
Negative Ions ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Physical Conditions ◽  
Numerical Characterization ◽  
Thermodynamic Conditions ◽  
Plasma Corona

A mono-dimensional code for the simulation of the effects of High Frequency Ignition systems (HFI) on the production of chemical radicals was developed and here presented. The simulations were carried out by considering the typical environmental thermodynamic conditions of a nowadays engine at full load. An electron transport model is linked with a Boltzmann solver coupled with a chemistry solver, affecting the Electron Energy Distribution Function (EEDF) in order to obtain the physical conditions leading to the production of radical components for a given fuel mixture. The transport equations for the electrons, the positive and the negative ions, and the Gauss’ law in a steady-state plasma region. Then the Boltzmann equation for the electrons, in a spatially homogeneous steady-state case, is solved in order to obtain the EEDF. Finally the chemical kinetics model is employed assuming a fuel-air mixture neglecting the fuel carbon atoms due to the assumption that electron-impact dissociation reactions, which initiate the combustion, exhibit a greater reaction rate compared to those based on hydrocarbon thermal dissociation and therefore can be neglected in this work. Results show the production of the hydrogen (H), nitrogen (N), and oxygen (O) radicals and the radius of the initial discharge under different simulated engine operating conditions characterizing the role of a plasma corona effect for the induced chemical ignition in gasoline-powered engines.

Validation of On-line Respiration Meter and its Applications by Computer Simulation

1992 ◽  
Vol 26 (5-6) ◽  
pp. 1355-1363 ◽  
Author(s):  
C-W. Kim ◽  
H. Spanjers ◽  
A. Klapwijk
Keyword(s):  
Steady State ◽  
Activated Sludge ◽  
Respiration Rate ◽  
Oxygen Demand ◽  
Operating Conditions ◽  
Mass Balances ◽  
Short Term ◽  
Respiration Rates ◽  
On Line ◽  
Made In

An on-line respiration meter is presented to monitor three types of respiration rates of activated sludge and to calculate effluent and influent short term biochemical oxygen demand (BODst) in the continuous activated sludge process. This work is to verify if the calculated BODst is reliable and the assumptions made in the course of developing the proposed procedure were acceptable. A mathematical model and a dynamic simulation program are written for an activated sludge model plant along with the respiration meter based on mass balances of BODst and DO. The simulation results show that the three types of respiration rate reach steady state within 15 minutes under reasonable operating conditions. As long as the respiration rate reaches steady state the proposed procedure calculates the respiration rate that is equal to the simulated. Under constant and dynamic BODst loading, the proposed procedure is capable of calculating the effluent and influent BODst with reasonable accuracy.

Steady-state Security Assessment Based on K-Means Clustering Algorithm and Phasor Measurement Units

2020 ◽  
Vol 13 (4) ◽  
pp. 559-570
Author(s):  
Bassam A. Hemade ◽  
Hamed A. Ibrahim ◽  
Hossam E.A. Talaat
Keyword(s):  
Steady State ◽  
Clustering Algorithm ◽  
System Security ◽  
Phasor Measurement Units ◽  
Operating Conditions ◽  
Security Assessment ◽  
State Security ◽  
Phasor Measurement ◽  
Measurement Units ◽  
Silhouette Analysis

Background: The security assessment plays a crucial role in the operation of the modern interconnected power system network. Methods: Hence, this paper addresses the application of k-means clustering algorithm equipped with Principal Component Analysis (PCA) and silhouette analysis for the classification of system security states. The proposed technique works on three principal axes; the first stage involves contingency quantification based on developed insecurity indices, the second stage includes dataset preparation to enhance the overall performance of the proposed method using PCA and silhouette analysis, and finally the application of the clustering algorithm over data. Results: The proposed composite insecurity index uses available synchronized measurements from Phasor Measurement Units (PMUs) to assess the development of cascading outages. Considering different operational scenarios and multiple levels of contingencies (up to N-3), Fast Decoupled Power Flow (FDPF) have been used for contingency replications. The developed technique applied to IEEE 14-bus and 57-bus standard test system for steady-state security evaluation. Conclusion: The obtained results ensure the robustness and effectiveness of the established procedure in the assessment of the system security irrespective of the network size or operating conditions.

Mathematical modelling of salt purification by recrystallization. Countercurrent arrangement

1986 ◽  
Vol 51 (11) ◽  
pp. 2481-2488
Author(s):  
Benitto Mayrhofer ◽  
Jana Mayrhoferová ◽  
Lubomír Neužil ◽  
Jaroslav Nývlt
Keyword(s):  
Steady State ◽  
Simple Model ◽  
Mathematical Modelling ◽  
Distribution Coefficient ◽  
Mother Liquor ◽  
Equilibrium Temperature ◽  
Operating Conditions ◽  
Limiting Case

The paper presents a simple model of recrystallization with countercurrent flows of the solution and the crystals being purified. The model assumes steady-state operating conditions, an equilibrium between the outlet streams of each stage, and the same equilibrium temperature and distribution coefficient for all stages. With these assumptions, the model provides the basis for analyzing the variation in the degree of purity as a function of the number of recrystallization stages. The analysis is facilitated by the use of a diagram constructed for the limiting case of perfect removal of the mother liquor from the crystals between the stages.

scholarly journals Crystal growth of clathrate hydrate formed with H2 + CO2 mixed gas and tetrahydropyran

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Meku Maruyama ◽  
Riku Matsuura ◽  
Ryo Ohmura
Keyword(s):  
Crystal Growth ◽  
Synthesis Gas ◽  
Water System ◽  
Hydrate Formation ◽  
Growth Dynamics ◽  
Operating Conditions ◽  
Mixed Gas ◽  
Thermodynamic Conditions ◽  
The Individual ◽  
And Storage

AbstractHydrate-based gas separation technology is applicable to the CO2 capture and storage from synthesis gas mixture generated through gasification of fuel sources including biomass. This paper reports visual observations of crystal growth dynamics and crystal morphology of hydrate formed in the H2 + CO2 + tetrahydropyran (THP) + water system with a target for developing the hydrate-based CO2 separation process design. Experiments were conducted at a temperature range of 279.5–284.9 K under the pressure of 4.9–5.3 MPa. To simulate the synthesis gas, gas composition in the gas phase was maintained around H2:CO2 = 0.6:0.4 in mole fraction. Hydrate crystals were formed and extended along the THP/water interface. After the complete coverage of the interface to shape a polycrystalline shell, hydrate crystals continued to grow further into the bulk of liquid water. The individual crystals were identified as hexagonal, tetragonal and other polygonal-shaped formations. The crystal growth rate and the crystal size varied depending on thermodynamic conditions. Implications from the obtained results for the arrangement of operating conditions at the hydrate formation-, transportation-, and dissociation processes are discussed.

scholarly journals Octane Index Applicability over the Pressure-Temperature Domain

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 607
Author(s):  
Tommy R. Powell ◽  
James P. Szybist ◽  
Flavio Dal Forno Chuahy ◽  
Scott J. Curran ◽  
John Mengwasser ◽  
...  
Keyword(s):  
High Efficiency ◽  
National Laboratory ◽  
Operating Conditions ◽  
Dominant Factor ◽  
Compression Ignition ◽  
Oak Ridge ◽  
Operating Modes ◽  
Wide Range ◽  
Thermodynamic Conditions ◽  
Si Engines

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

Design and Performance of a Controlled Turbocharging System on Marine Diesel Engines

2006 ◽  
Author(s):  
Ioannis Vlaskos ◽  
Ennio Codan ◽  
Nikolaos Alexandrakis ◽  
George Papalambrou ◽  
Marios Ioannou ◽  
...  
Keyword(s):  
Steady State ◽  
Engine Performance ◽  
Operating Conditions ◽  
Electric Actuator ◽  
Engine Simulation ◽  
Engine Control System ◽  
Turbocharging System ◽  
Compressor Impeller ◽  
Marine Diesel ◽  
And Performance

The paper describes the design process for a controlled pulse turbocharging system (CPT) on a 5 cylinder 4-stroke marine engine and highlights the potential for improved engine performance as well as reduced smoke emissions under steady state and transient operating conditions, as offered by the following technologies: • controlled pulse turbocharging, • high pressure air injection onto the compressor impeller as well as into the air receiver, and • an electronic engine control system, including a hydraulic powered electric actuator. Calibrated engine simulation computer models based on the results of tests performed on the engine in its baseline configuration were used to design the CPT components. Various engine tests with CPT under steady state and transient operating conditions show the engine optimization process and how the above-mentioned technologies benefit engine behavior in both generator and propeller law operation.

Thermo-structural analysis of a honeycomb-type volumetric absorber for concentrated solar power applications

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Masoud Behzad ◽  
Benjamin Herrmann ◽  
Williams R. Calderón-Muñoz ◽  
José M. Cardemil ◽  
Rodrigo Barraza
Keyword(s):  
Heat Transfer ◽  
Thermal Stress ◽  
Steady State ◽  
Discrete Model ◽  
Continuum Model ◽  
Transient State ◽  
Operating Conditions ◽  
Steady State Condition ◽  
Content Type ◽  
The Continuum

Purpose Volumetric air receivers experience high thermal stress as a consequence of the intense radiation flux they are exposed to when used for heat and/or power generation. This study aims to propose a proper design that is required for the absorber and its holder to ensure efficient heat transfer between the fluid and solid phases and to avoid system failure due to thermal stress. Design/methodology/approach The design and modeling processes are applied to both the absorber and its holder. A multi-channel explicit geometry design and a discrete model is applied to the absorber to investigate the conjugate heat transfer and thermo-mechanical stress levels present in the steady-state condition. The discrete model is used to calibrate the initial state of the continuum model that is then used to investigate the transient operating states representing cloud-passing events. Findings The steady-state results constitute promising findings for operating the system at the desired airflow temperature of 700°C. In addition, we identified regions with high temperatures and high-stress values. Furthermore, the transient state model is capable of capturing the heat transfer and fluid dynamics phenomena, allowing the boundaries to be checked under normal operating conditions. Originality/value Thermal stress analysis of the absorber and the steady/transient-state thermal analysis of the absorber/holder were conducted. Steady-state heat transfer in the explicit model was used to calibrate the initial steady-state of the continuum model.

Investigating realistic anode off-gas combustion in SOFC/ICE hybrid systems: mini review and experimental evaluation

2021 ◽  
pp. 146808742110583
Author(s):  
Ioannis Nikiforakis ◽  
Zhongnan Ran ◽  
Michael Sprengel ◽  
John Brackett ◽  
Guy Babbit ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
High Energy ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Case Scenario ◽  
Gas Combustion ◽  
Thermodynamic Conditions ◽  
Decentralized Energy

Solid oxide fuel cells (SOFCs) have been deployed in hybrid decentralized energy systems, in which they are directly coupled to internal combustion engines (ICEs). Prior research indicated that the anode tailgas exiting the SOFC stack should be additionally exploited due to its high energy value, with typical ICE operation favoring hybridization due to matching thermodynamic conditions during operation. Consequently, extensive research has been performed, in which engines are positioned downstream the SOFC subsystem, operating in several modes of combustion, with the most prevalent being homogeneous compression ignition (HCCI) and spark ignition (SI). Experiments were performed in a 3-cylinder ICE operating in the latter modus operandi, where the anode tailgas was assimilated by mixing syngas (H2: 33.9%, CO: 15.6%, CO2: 50.5%) with three different water vapor flowrates in the engine’s intake. While increased vapor content significantly undermined engine performance, brake thermal efficiency (BTE) surpassed 34% in the best case scenario, which outperformed the majority of engines operating under similar operating conditions, as determined from the conducted literature review. Nevertheless, the best performing application was identified operating under HCCI, in which diesel reformates assimilating SOFC anode tailgas, fueled a heavy duty ICE (17:1), and gross indicated thermal efficiency ([Formula: see text]) of 48.8% was achieved, with the same engine exhibiting identical performance when operating in reactivity-controlled compression ignition (RCCI). Overall, emissions in terms of NOx and CO were minimal, especially in SI engines, while unburned hydrocarbons (UHC) were non-existent due to the absence of hydrocarbons in the assessed reformates.

Sign in / Sign up

Export Citation Format

Share Document