scholarly journals A Comparative Analysis of Half-Bridge LLC Resonant Converters Using Si and SiC MOSFETs

2021 ◽  
Vol 12 (1) ◽  
pp. 43
Author(s):  
Hasaan Farooq ◽  
Hassan Abdullah Khalid ◽  
Waleed Ali ◽  
Ismail Shahid
Keyword(s):  
Silicon Carbide ◽  
Renewable Energy ◽  
High Frequency ◽  
High Efficiency ◽  
Low Voltage ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
Resonant Converters ◽  
Wide Range

With the expansion of renewable energy sources worldwide, the need for developing more economical and more efficient converters that can operate on a high frequency with minimal switching and conduction losses has been increased. In power electronic converters, achieving high efficiency is one of the most challenging targets to achieve. The utilization of wideband switches can achieve this goal but add additional cost to the system. LLC resonant converters are widely used in different applications of renewable energy systems, i.e., PV, wind, hydro and geothermal, etc. This type of converter has more benefits than the other converters such as high electrical isolation, high power density, low EMI, and high efficiency. In this paper, a comparison between silicon carbide (SiC) MOSFET and silicon (Si) MOSFET switches was made, by considering a 3KW half-bridge LLC converter with a wide range of input voltage. The switching losses and conduction losses were analyzed through mathematical calculations, and their authenticity was validated with the help of software simulations in PSIM. The results show that silicon carbide (SiC) MOSFETs can work more efficiently, as compared with silicon (Si) MOSFETs in high-frequency power applications. However, in low-voltage and low-power applications, Si MOSFETs are still preferable due to their low-cost advantage.

A High Step-up DC-DC Converter Based on the Voltage Lift Technique for Renewable Energy Applications

2021 ◽  
Vol 13 (19) ◽  
pp. 11059
Author(s):  
Shahrukh Khan ◽  
Arshad Mahmood ◽  
Mohammad Zaid ◽  
Mohd Tariq ◽  
Chang-Hua Lin ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Common Ground ◽  
Closed Loop ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain

High gain DC-DC converters are getting popular due to the increased use of renewable energy sources (RESs). Common ground between the input and output, low voltage stress across power switches and high voltage gain at lower duty ratios are desirable features required in any high gain DC-DC converter. DC-DC converters are widely used in DC microgrids to supply power to meet local demands. In this work, a high step-up DC-DC converter is proposed based on the voltage lift (VL) technique using a single power switch. The proposed converter has a voltage gain greater than a traditional boost converter (TBC) and Traditional quadratic boost converter (TQBC). The effect of inductor parasitic resistances on the voltage gain of the converter is discussed. The losses occurring in various components are calculated using PLECS software. To confirm the performance of the converter, a hardware prototype of 200 W is developed in the laboratory. The simulation and hardware results are presented to determine the performance of the converter in both open-loop and closed-loop conditions. In closed-loop operation, a PI controller is used to maintain a constant output voltage when the load or input voltage is changed.

scholarly journals Non-isolated multiple input multilevel output DC-DC converter for hybrid power system

2020 ◽  
Vol 19 (2) ◽  
pp. 635
Author(s):  
Ameen M. Al-Modaffer ◽  
Amer A. Chlaihawi ◽  
Husam A. Wahhab
Keyword(s):  
Renewable Energy ◽  
Power System ◽  
High Efficiency ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
Hybrid Power System ◽  
Hybrid Power ◽  
Multiple Input ◽  
Single Input ◽  
High Conversion Ratio

<p><span>The utilization of multisources of energy in a compact and an effective power system gains an essential role in power electronic industry. As such, the design and simulation of a new non-isolated Multiple Input Multilevel Output (MIMLO) DC-DC converter for hybrid power system is presented. The MIMLO DC-DC converter can be integrated in renewable energy, such as fuel cells, wind turbines and photovoltaic arrays etc, to get the best output voltages. The MIMLO DC-DC converter powers the load from renewable energy sources through the independence of the availability of other sources. The proposed topology has been simulated by using MATLAB/Simulink software to testify the performance control operation of the Multiple Input Multilevel Output DC-DC converter. The results of the carried-out simulation favor the usage of multi-input voltage, rather than a single input voltage. The MIMLO design has the advantages of a simple configuration, reduced number of switches, fewer components, high efficiency, and high conversion ratio. The Multilevel Output DC-DC converter provides high voltage transfer with low size inductors, reduction of losses, low stress voltage on switches and diodes. </span></p>

scholarly journals A High-Efficiency, Low-Cost Solution for On-Board Power Converters

2012 ◽  
Vol 2012 ◽  
pp. 1-12 ◽  
Author(s):  
V. Boscaino ◽  
G. Capponi
Keyword(s):  
Power Efficiency ◽  
High Efficiency ◽  
Low Voltage ◽  
Low Cost ◽  
Input Voltage ◽  
High Current ◽  
Forward Converter ◽  
System Cost ◽  
Zero Voltage Switching ◽  
Reset Voltage

Wide-input, low-voltage, and high-current applications are addressed. A single-ended isolated topology which improves the power efficiency, reduces both switching and conduction losses, and heavily lowers the system cost is presented. During each switching cycle, the transformer core reset is provided. The traditional tradeoff between the maximum allowable duty-cycle and the reset voltage is avoided and the off-voltage of active switches is clamped to the input voltage. Therefore, the system cost is heavily reduced and the converter is well suited for wide-input applications. Zero-voltage switching is achieved for active switches, and the power efficiency is greatly improved. In the output mesh, an inductor is included making the converter suitable for high-current, low-voltage applications. Since the active clamp forward converter is the closest competitor of the proposed converter, a comparison is provided as well. In this paper, the steady-state and small-signal analysis of the proposed converter is presented. Design examples are provided for further applications. Simulation and experimental results are shown to validate the great advantages brought by the proposed topology.

scholarly journals Holistic simulation of wind turbines with fully aero-elastic and electrical model

2021 ◽  
Author(s):  
Marcus Wiens ◽  
Sebastian Frahm ◽  
Philipp Thomas ◽  
Shoaib Kahn
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Elastic Model ◽  
Electrical Model ◽  
Holistic Model ◽  
Electric System ◽  
Electrical Components

AbstractRequirements for the design of wind turbines advance facing the challenges of a high content of renewable energy sources in the public grid. A high percentage of renewable energy weaken the grid and grid faults become more likely, which add additional loads on the wind turbine. Load calculations with aero-elastic models are standard for the design of wind turbines. Components of the electric system are usually roughly modeled in aero-elastic models and therefore the effect of detailed electrical models on the load calculations is unclear. A holistic wind turbine model is obtained, by combining an aero-elastic model and detailed electrical model into one co-simulation. The holistic model, representing a DFIG turbine is compared to a standard aero-elastic model for load calculations. It is shown that a detailed modelling of the electrical components e.g., generator, converter, and grid, have an influence on the results of load calculations. An analysis of low-voltage-ride-trough events during turbulent wind shows massive increase of loads on the drive train and effects the tower loads. Furthermore, the presented holistic model could be used to investigate different control approaches on the wind turbine dynamics and loads. This approach is applicable to the modelling of a holistic wind park to investigate interaction on the electrical level and simultaneously evaluate the loads on the wind turbine.

scholarly journals Forecasting and Modelling the Uncertainty of Low Voltage Network Demand and the Effect of Renewable Energy Sources

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2151
Author(s):  
Feras Alasali ◽  
Husam Foudeh ◽  
Esraa Mousa Ali ◽  
Khaled Nusair ◽  
William Holderbaum
Keyword(s):  
Renewable Energy ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Golden Ratio ◽  
Clean Energy ◽  
Energy Sources ◽  
Percentage Error ◽  
Ann Model ◽  
Demand Forecast ◽  
Pv System

More and more households are using renewable energy sources, and this will continue as the world moves towards a clean energy future and new patterns in demands for electricity. This creates significant novel challenges for Distribution Network Operators (DNOs) such as volatile net demand behavior and predicting Low Voltage (LV) demand. There is a lack of understanding of modern LV networks’ demand and renewable energy sources behavior. This article starts with an investigation into the unique characteristics of householder demand behavior in Jordan, connected to Photovoltaics (PV) systems. Previous studies have focused mostly on forecasting LV level demand without considering renewable energy sources, disaggregation demand and the weather conditions at the LV level. In this study, we provide detailed LV demand analysis and a variety of forecasting methods in terms of a probabilistic, new optimization learning algorithm called the Golden Ratio Optimization Method (GROM) for an Artificial Neural Network (ANN) model for rolling and point forecasting. Short-term forecasting models have been designed and developed to generate future scenarios for different disaggregation demand levels from households, small cities, net demands and PV system output. The results show that the volatile behavior of LV networks connected to the PV system creates substantial forecasting challenges. The mean absolute percentage error (MAPE) for the ANN-GROM model improved by 41.2% for household demand forecast compared to the traditional ANN model.

scholarly journals Pretreatments of lignocellulosic feedstock for bioethanol production

2010 ◽  
Vol 64 (4) ◽  
pp. 283-293 ◽  
Author(s):  
Zlatica Predojevic
Keyword(s):  
Renewable Energy ◽  
Co2 Emission ◽  
Fossil Fuels ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Energy Sources ◽  
Bioethanol Production ◽  
Environment Protection ◽  
Lignocellulosic Feedstock ◽  
Lignocellulosic Feedstocks

The use of renewable energy sources (biofuels), either as a component in the conventional fossil fuels, gasoline and diesel, or as a pure biofuel, contributes to energy saving and decrease of total CO2 emission. The use of bioethanol mixed with gasoline significantly decreases gasoline consumption and contributes to environment protection. One of the problems in the production of bioethanol is the availability of sugar and starch based feedstock used for its production. However, lignocellulosic feedstocks are becoming more significant in the production of bioethanol due to their availability and low cost. The aim of this study is to point out the advantages and shortcomings of pretreatment processes and hydrolyses of lignocellulosic feedstocks that precede their fermentation to bioethanol.

scholarly journals Development of a Micro grid with Renewable Energy Sources with Feedback Controller

2019 ◽  
Vol 8 (11) ◽  
pp. 2014-2018
Keyword(s):  
Renewable Energy ◽  
Electricity Generation ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Electrical Power ◽  
Energy Sources ◽  
Military Operations ◽  
Urban Centers ◽  
Industrial Projects ◽  
Micro Grid

To make micro grid with renewable energy and to over come the technical challenges and economy base and policy and regulatory challenges . From the natural wastage we can generate the Electricity. Thus, the Electrical Power or Electricity is available with a low cost and pollution free to anyplace in the world at all times. This process divulge a unequaled step in electricity generation and this type of generation is maintain the ecological balance. We can have an uninterrupted power supply irrespective of the natural condition without any kind of environmental pollution. More influence this process relent the less production cost for electricity generation. Micro grids have long been used in remote areas to power off-grid villages, military operations or industrial projects. But increasingly they are being used in cities or towns, in urban centers. Here we try a proto type of micro grid with renewable energy sources.

scholarly journals Experimental Studies on an Inclined Collector Divergent Chimney Pilot Plant

2021 ◽  
Vol 850 (1) ◽  
pp. 012008
Author(s):  
N Rajamurugu
Keyword(s):  
Renewable Energy ◽  
Fossil Fuels ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Experimental Studies ◽  
High Mass ◽  
Energy Sources ◽  
Solar Pv ◽  
Solar Chimney ◽  
Energy Agency

Abstract Renewable energy sources become suitable valid options to reduce the dependency on fossil fuels or petroleum products. The International Renewable Energy Agency reports that the world will harvest 40% of energy from renewable energy sources by 2030. Conventional technologies such as solar PV technology, consumes higher capital per unit (kWh) of electricity generation cost significantly higher than the traditional sources. Hence, solar chimney power generation system can be suitable option for generating low cost energy. Solar chimneys are developed and tested by different researchers in enhancing the performance of the system. Studies on the geometric modifications of the collector, and chimney are limited. The aim of this paper is to analyse the experimental data obtained from a divergent solar chimney. Experimentation is carried under sunlight in an open atmosphere. The airflow rates in the chimneys are tested under different collector outlet height. The experimental results showed that a chimney with higher collector openings was performed well than other models. The computational analysis is also carried out using ANSYS Fluent software package which shows that the collector opening of 2.5m is recommended for higher high mass flow rate and system efficiency.

scholarly journals An Overview of Bidirectional AC-DC Grid Connected Converter Topologies for Low Voltage Battery Integration

2018 ◽  
Vol 9 (3) ◽  
pp. 1223 ◽  
Author(s):  
Kaspars Kroics ◽  
Oleksandr Husev ◽  
Kostiantyn Tytelmaier ◽  
Janis Zakis ◽  
Oleksandr Veligorskyi
Keyword(s):  
Energy Storage ◽  
High Efficiency ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Storage System ◽  
Distribution Grid ◽  
Battery Energy Storage ◽  
Battery Energy Storage Systems ◽  
Converter Topologies ◽  
Battery Energy

<p>Battery energy storage systems are becoming more and more popular solution in the household applications, especially, in combination with renewable energy sources. The bidirectional AC-DC power electronic converter have great impact to the overall efficiency, size, mass and reliability of the storage system. This paper reviews the literature that deals with high efficiency converter technologies for connecting low voltage battery energy storage to an AC distribution grid. Due to low voltage of the battery isolated bidirectional AC-DC converter or a dedicated topology of the non isolated converter is required. Review on single stage, two stage power converters and integrated solutions are done in the paper.</p>

Microgrid Model on Homer Software

2021 ◽  
Vol 9 (VI) ◽  
pp. 757-760
Author(s):  
Mohd Ahamad
Keyword(s):  
Power Generation ◽  
Power Electronics ◽  
Life Cycle Cost ◽  
Low Voltage ◽  
High Reliability ◽  
Low Cost ◽  
Local Area ◽  
New Paradigm ◽  
Power Sources ◽  
Wide Range

A new concept in power generation is a microgrid. The Microgrid concept assumes a cluster of loads and microsources operating as a single controllable system that provides power to its local area. This concept provides a new paradigm for defining the operation of distributed generation. The microsources of special interest for MGs are small (<100-kW) units with power electronic interfaces. These sources are placed at customers sites. They are low cost, low voltage and have a high reliability with few emissions. Power electronics provide the control and flexibility required by the MG concept. A properly designed power electronics and controllers insure that the MG can meet the needs of its customers as well as the utilities. The goal of this project is to build a complete model of Microgrid including the power sources, their power electronics, and a load and mains model in THE HOMER. The HOMER Micropower Optimization Model is a computer model developed by the U.S. National Renewable Energy Laboratory (NREL) to assist in the design of micropower systems and to facilitate the comparison of power generation technologies across a wide range of applications. HOMER models a power system’s physical behavior and its life-cycle cost, which is the total cost of installing and operating the system over its life span. HOMER allows the modeler to compare many different design options based on their technical and economic merits. It also assists in understanding and quantifying the effects of uncertainty or changes in the inputs.

Sign in / Sign up

Export Citation Format

Share Document