scholarly journals Wood Protection through Plasma Powder Deposition—An Alternative Coating Process

Forests ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 898 ◽  
Author(s):  
Robert Köhler ◽  
Philipp Sauerbier ◽  
Gisela Ohms ◽  
Wolfgang Viöl ◽  
Holger Militz
Keyword(s):  
Water Vapor ◽  
Metal Oxide ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Atmospheric Pressure Plasma ◽  
European Beech ◽  
Layer System ◽  
Water Vapor Absorption ◽  
Powder Deposition

In contrast to conventional coating processes such as varnishing, plasma powder deposition by means of an atmospheric pressure plasma jet on wood is not yet widely used. A key advantage of this process is that volatile organic compounds and organic solvents are avoided. In the present work, European beech (Fagus sylvatica L.) and pine sapwood (Pinus sylvestris L.) were coated with polymer (polyester), metal (aluminum coated silver) or metal oxide (bismuth oxide) particles. Furthermore, a layer system consisting of polyester and metal or metal oxide was investigated. The layer thickness and topography were analyzed with a laser scanning microscope and scanning electron microscope, revealing thicknesses of 2–22 µm depending on the coating material. In general, the chemical composition of the layers was determined using X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy measurements. The coatings consisting of metal and metal oxide showed a band gap and plasmon resonance in the range of 540 and 450 nm. Through this absorption, the wood may be protected against ultraviolet (UV) radiation. In the water uptake and release tests, the polyester layers exhibited a reduction of water vapor absorption after 24 h in 100% relative humidity (RH) by 53%–66%, whereas the pure metal oxide layers indicated the best desorption performance. The combination of metal oxide and polyester in the one-layer system combines the protection properties of the single coatings against water vapor and UV radiation.

scholarly journals Surface Activation of Polylactic Acid-Based Wood-Plastic Composite by Atmospheric Pressure Plasma Treatment

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4673 ◽  
Author(s):  
Philipp Sauerbier ◽  
Robert Köhler ◽  
Gerrit Renner ◽  
Holger Militz
Keyword(s):  
Plasma Treatment ◽  
Polylactic Acid ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Atmospheric Pressure Plasma ◽  
Contact Angles ◽  
Laser Scanning Microscopy ◽  
Wood Plastic Composite ◽  
Dbd Plasma ◽  
Plastic Composite

Wood-plastic composite (WPC) based on a polylactic acid (PLA) matrix is a promising material since it is biobased, degradable, sustainable, and 3D printable. However, due to its coloring, visible layers after 3D-printing, and small build volumes of these printers, a coating or gluing of parts might be required. This study investigates the influence of a dielectric barrier discharge (DBD) plasma treatment of PLA-based WPC to activate the surface and improve, e.g., coating capabilities. X-ray photoelectron spectroscopy (XPS) measurements showed the oxidation of the surface due to the formation of carbonyl and carboxyl groups. Laser scanning microscopy revealed a surface roughening after the treatment. Contact angles of water and diiodomethane decreased significantly after the plasma treatment and the consecutively calculated surface free energy increased. Finally, two practical adhesion tests revealed an improvement of the applied acrylic dispersion coating’s adhesion to the WPC surface: The assigned cross-cut class improved, and the pull-off strength increased from 1.4 to 2.3 N/mm2.

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

scholarly journals Investigation of Spin Coating Cerium-Doped Hydroxyapatite Thin Films with Antifungal Properties

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 464
Author(s):  
Simona Liliana Iconaru ◽  
Mihai Valentin Predoi ◽  
Patrick Chapon ◽  
Sofia Gaiaschi ◽  
Krzysztof Rokosz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Spin Coating ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
X Ray ◽  
Antifungal Properties ◽  
Scanning Electron

In this study, the cerium-doped hydroxyapatite (Ca10−xCex(PO4)6(OH)2 with xCe = 0.1, 10Ce-HAp) coatings obtained by the spin coating method were presented for the first time. The stability of the 10Ce-HAp suspension particles used in the preparation of coatings was evaluated by ultrasonic studies, transmission electron microscopy (TEM), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The surface morphology of the 10Ce-HAp coating was studied by SEM and atomic force microscopy (AFM) techniques. The obtained 10Ce-HAp coatings were uniform and without cracks or unevenness. Glow discharge optical emission spectroscopy (GDOES) and X-ray photoelectron spectroscopy (XPS) were used for the investigation of fine chemical depth profiling. The antifungal properties of the HAp and 10Ce-HAp suspensions and coatings were assessed using Candida albicans ATCC 10231 (C. albicans) fungal strain. The quantitative antifungal assays demonstrated that both 10Ce-HAp suspensions and coatings exhibited strong antifungal properties and that they successfully inhibited the development and adherence of C. albicans fungal cells for all the tested time intervals. The scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) visualization of the C. albicans fungal cells adherence to the 10Ce-HAp surface also demonstrated their strong inhibitory effects. In addition, the qualitative assays also suggested that the 10Ce-HAp coatings successfully stopped the biofilm formation.

Understanding the mechanism of photochromism in double-layer metal oxide using X-ray photoelectron spectroscopy

2020 ◽  
Vol 739 ◽  
pp. 136973
Author(s):  
Hidetaka Takaki ◽  
Keita Shinzato ◽  
Shuhei Inoue ◽  
Hiroki Miyaoka ◽  
Takayuki Ichikawa ◽  
...  
Keyword(s):  
Metal Oxide ◽  
Double Layer ◽  
Photoelectron Spectroscopy ◽  
X Ray
Sign in / Sign up

Export Citation Format

Share Document