scholarly journals Surface Activation of Polylactic Acid-Based Wood-Plastic Composite by Atmospheric Pressure Plasma Treatment

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4673 ◽  
Author(s):  
Philipp Sauerbier ◽  
Robert Köhler ◽  
Gerrit Renner ◽  
Holger Militz
Keyword(s):  
Plasma Treatment ◽  
Polylactic Acid ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Atmospheric Pressure Plasma ◽  
Contact Angles ◽  
Laser Scanning Microscopy ◽  
Wood Plastic Composite ◽  
Dbd Plasma ◽  
Plastic Composite

Wood-plastic composite (WPC) based on a polylactic acid (PLA) matrix is a promising material since it is biobased, degradable, sustainable, and 3D printable. However, due to its coloring, visible layers after 3D-printing, and small build volumes of these printers, a coating or gluing of parts might be required. This study investigates the influence of a dielectric barrier discharge (DBD) plasma treatment of PLA-based WPC to activate the surface and improve, e.g., coating capabilities. X-ray photoelectron spectroscopy (XPS) measurements showed the oxidation of the surface due to the formation of carbonyl and carboxyl groups. Laser scanning microscopy revealed a surface roughening after the treatment. Contact angles of water and diiodomethane decreased significantly after the plasma treatment and the consecutively calculated surface free energy increased. Finally, two practical adhesion tests revealed an improvement of the applied acrylic dispersion coating’s adhesion to the WPC surface: The assigned cross-cut class improved, and the pull-off strength increased from 1.4 to 2.3 N/mm2.

scholarly journals Plasma Treatment of Polypropylene-Based Wood–Plastic Composites (WPC): Influences of Working Gas

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1933
Author(s):  
Philipp Sauerbier ◽  
Robert Köhler ◽  
Gerrit Renner ◽  
Holger Militz
Keyword(s):  
Plasma Treatment ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
Injection Molded ◽  
Wood Content ◽  
Measurement Artifacts

In this study, a polypropylene (PP)-based wood–plastic composite with maleic anhydride-grafted polypropylene (MAPP) as a coupling agent and a wood content of 60% was extruded and specimens were injection molded. The samples were plasma treated utilizing a dielectric barrier discharge (DBD) setup with three different working gases: Ar/O2 (90%/10%), Ar/N2 (90%/10%), and synthetic air. This process aims to improve the coating and gluing properties of the otherwise challenging apolar surface of PP based wood–plastic composites (WPC). Chemical analysis with X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) showed the formation of oxygen-based functional groups on the surface, independently from the working gas used for the treatment. Laser scanning microscopy (LSM) examined the surface roughness and revealed that the two argon-containing working gases roughened the surface more than synthetic air. However, the contact angle for water was reduced significantly after treatment, revealing measurement artifacts for water and diiodomethane due to the severe changes in surface morphology. The adhesion of acrylic dispersion coating was significantly increased, resulting in a pull-off strength of approximately 4 N/mm2, and cross-cut tests assigned the best adhesion class (0), on a scale from 0 to 5, after plasma treatment with any working gas.

scholarly journals Chemical, Thermo-Mechanical and Antimicrobial Properties of DBD Plasma Treated Disinfectant-Impregnated Wipes during Storage

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1769 ◽  
Author(s):  
Song ◽  
Cvelbar ◽  
Strazar ◽  
Vossebein ◽  
Zille
Keyword(s):  
Plasma Treatment ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Storage Time ◽  
Laser Scanning Microscopy ◽  
Elastic Response ◽  
Infection Prevention And Control ◽  
Ammonium Compound ◽  
Dbd Plasma ◽  
Etching Effect

Disinfectant-impregnated wipes are broadly used in hospitals, as an important approach for infection prevention and control. But their ageing performance has rarely been studied. Untreated and Dielectric Barrier Discharge (DBD) plasma pre-treated wiping materials made of nonwoven 100% polyester (W1), nonwoven 55% cellulose/45% polyester (W2) and woven cotton (W3) were impregnated with a quaternary ammonium compound solution (ADBAC) for 30 min, 3, 7, 15, and 30 days of storage time and characterized in term of chemical, thermo-mechanical and antimicrobial efficacy. X-ray photoelectron spectroscopy analysis on the plasma-treated polyester wipes demonstrates the incorporation of reactive oxygen species on the fiber surface. Laser scanning microscopy demonstrates the plasma etching effect in smoothing the surface of the cotton wipe reducing the adsorption of ADBAC. The result showed no significant changes in breaking force and elongation during storage for W1 and W2. However, plasma treatment affects W3 in weft direction reducing the force at break in water and ADBAC treated wipes. Dynamic mechanical analysis results show that ADBAC and plasma treatment have a significant influence in W1 and W3 viscoelastic properties improving the elastic response limiting the polymeric chains mobility and the non-elastic response due to the etching effect, respectively. Overall, the plasma pre-treatment of ADBAC-impregnated wipes is able to enhance the antimicrobial performance and the storage time of polyester-containing wipes.

scholarly journals Aluminium trihydrate-filled poly(methyl methacrylate) (PMMA/ATH) waste powder utilization in wood-plastic composite boards bonded by MUF resin

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 3252-3269
Author(s):  
Matej Vovk ◽  
Milan Šernek
Keyword(s):  
Surface Modification ◽  
Methyl Methacrylate ◽  
Photoelectron Spectroscopy ◽  
Urea Formaldehyde ◽  
Contact Angles ◽  
Modulus Of Rupture ◽  
Wood Plastic Composite ◽  
Silane Coupling Agents ◽  
Poly Methyl Methacrylate ◽  
Plastic Composite

An alternative approach to producing a wood-plastic composite (WPC) from wood particles, aluminium trihydrate-filled poly(methyl methacrylate) (PMMA/ATH) waste powder, and melamine-urea-formaldehyde (MUF) resin is described. The surface of PMMA/ATH powder was modified with ureido- and amino-functional silane coupling agents at four different degrees of modification: 0.3%, 0.5%, 1.0%, and 2.0%. An X-ray photoelectron spectroscopy (XPS) analysis was executed on a silane-modified PMMA/ATH material, and the results revealed the presence of chemically bonded silanes on the PMMA/ATH surface. Contact angle measurements were also performed to calculate the surface free energies of the modified powders. Water contact angles of modified powders slightly decreased as surface free energy increased with the degree of surface modification. Mechanical tests of the composites showed that different degrees of surface modification had a significant influence on modulus of elasticity (MOE) and modulus of rupture (MOR) of the composite boards. However, there were no significant differences between the silanes used.

scholarly journals Investigation of Spin Coating Cerium-Doped Hydroxyapatite Thin Films with Antifungal Properties

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 464
Author(s):  
Simona Liliana Iconaru ◽  
Mihai Valentin Predoi ◽  
Patrick Chapon ◽  
Sofia Gaiaschi ◽  
Krzysztof Rokosz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Spin Coating ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
X Ray ◽  
Antifungal Properties ◽  
Scanning Electron

In this study, the cerium-doped hydroxyapatite (Ca10−xCex(PO4)6(OH)2 with xCe = 0.1, 10Ce-HAp) coatings obtained by the spin coating method were presented for the first time. The stability of the 10Ce-HAp suspension particles used in the preparation of coatings was evaluated by ultrasonic studies, transmission electron microscopy (TEM), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The surface morphology of the 10Ce-HAp coating was studied by SEM and atomic force microscopy (AFM) techniques. The obtained 10Ce-HAp coatings were uniform and without cracks or unevenness. Glow discharge optical emission spectroscopy (GDOES) and X-ray photoelectron spectroscopy (XPS) were used for the investigation of fine chemical depth profiling. The antifungal properties of the HAp and 10Ce-HAp suspensions and coatings were assessed using Candida albicans ATCC 10231 (C. albicans) fungal strain. The quantitative antifungal assays demonstrated that both 10Ce-HAp suspensions and coatings exhibited strong antifungal properties and that they successfully inhibited the development and adherence of C. albicans fungal cells for all the tested time intervals. The scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) visualization of the C. albicans fungal cells adherence to the 10Ce-HAp surface also demonstrated their strong inhibitory effects. In addition, the qualitative assays also suggested that the 10Ce-HAp coatings successfully stopped the biofilm formation.

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

scholarly journals Wood Protection through Plasma Powder Deposition—An Alternative Coating Process

Forests ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 898 ◽  
Author(s):  
Robert Köhler ◽  
Philipp Sauerbier ◽  
Gisela Ohms ◽  
Wolfgang Viöl ◽  
Holger Militz
Keyword(s):  
Water Vapor ◽  
Metal Oxide ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Atmospheric Pressure Plasma ◽  
European Beech ◽  
Layer System ◽  
Water Vapor Absorption ◽  
Powder Deposition

In contrast to conventional coating processes such as varnishing, plasma powder deposition by means of an atmospheric pressure plasma jet on wood is not yet widely used. A key advantage of this process is that volatile organic compounds and organic solvents are avoided. In the present work, European beech (Fagus sylvatica L.) and pine sapwood (Pinus sylvestris L.) were coated with polymer (polyester), metal (aluminum coated silver) or metal oxide (bismuth oxide) particles. Furthermore, a layer system consisting of polyester and metal or metal oxide was investigated. The layer thickness and topography were analyzed with a laser scanning microscope and scanning electron microscope, revealing thicknesses of 2–22 µm depending on the coating material. In general, the chemical composition of the layers was determined using X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy measurements. The coatings consisting of metal and metal oxide showed a band gap and plasmon resonance in the range of 540 and 450 nm. Through this absorption, the wood may be protected against ultraviolet (UV) radiation. In the water uptake and release tests, the polyester layers exhibited a reduction of water vapor absorption after 24 h in 100% relative humidity (RH) by 53%–66%, whereas the pure metal oxide layers indicated the best desorption performance. The combination of metal oxide and polyester in the one-layer system combines the protection properties of the single coatings against water vapor and UV radiation.

scholarly journals In Situ Surface Modification of Paper-Based Relics with Atmospheric Pressure Plasma Treatment for Preservation Purposes

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 786
Author(s):  
Xu Yan ◽  
Guo-Sai Liu ◽  
Jing Yang ◽  
Yi Pu ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Atmospheric Pressure Plasma ◽  
Good Method ◽  
Contact Angles ◽  
Water Penetration ◽  
Water Contact ◽  
Pressure Plasma ◽  
Static Water

Paper-based relics, which are an important part of cultural heritage worldwide, are at risk of imminent damage from various environmental sources. To protect them, the atmospheric pressure plasma polymerization of hexamethyldisiloxane (HMDSO) precursor has been explored on paper-based relics in situ. The macro and micro images taken during this process suggest that the in situ plasma treatment does not change the macro morphology and the micro structure of the treated paper-based relic samples. On the other hand, plasma treatment causes the polymerization of the HMDSO which then produces nanoparticles deposited onto the paper-based relics. These nanoparticles provide good waterproof properties with large static water contact angles and smaller rolling angles, which protect the paper-based relics from water penetration. Moreover, since the nanoparticles are deposited onto the fibers, waterproof fastness is ensured. Also, the examined mechanical properties of the treated and untreated paper-based relics indicate that the atmospheric pressure plasma treatment does not affect the strength of the paper very much. The results in this study show that atmospheric pressure plasma treatment with the use of HMDSO precursor is a good method to preserve paper-based relics.

scholarly journals Antimicrobial Activity Evaluation on Silver Doped Hydroxyapatite/Polydimethylsiloxane Composite Layer

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
C. S. Ciobanu ◽  
A. Groza ◽  
S. L. Iconaru ◽  
C. L. Popa ◽  
P. Chapon ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Candida Albicans ◽  
Photoelectron Spectroscopy ◽  
Laser Scanning ◽  
Composite Layer ◽  
Physicochemical Characterization ◽  
Antimicrobial Effect ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Composite Layers

The goal of this study was the preparation, physicochemical characterization, and microbiological evaluation of novel hydroxyapatite doped with silver/polydimethylsiloxane (Ag:HAp-PDMS) composite layers. In the first stage, the deposition of polydimethylsiloxane (PDMS) polymer layer on commercially pure Si disks has been produced in atmospheric pressure corona discharges. Finally, the new silver doped hydroxyapatite/polydimethylsiloxane composite layer has been obtained by the thermal evaporation technique. The Ag:HAp-PDMS composite layers were characterized by various techniques, such as Scanning Electron Microscopy (SEM), Glow Discharge Optical Emission Spectroscopy (GDOES), and X-ray photoelectron spectroscopy (XPS). The antimicrobial activity of the Ag:HAp-PDMS composite layer was assessed againstCandida albicansATCC 10231 (ATCC—American Type Culture Collection) by culture based and confirmed by SEM and Confocal Laser Scanning Microscopy (CLSM) methods. This is the first study reporting the antimicrobial effect of the Ag:HAp-PDMS composite layer, which proved to be active againstCandida albicansbiofilm embedded cells.

Sign in / Sign up

Export Citation Format

Share Document