scholarly journals Numerical Simulation of Breathing Mode Oscillation on Bubble Detachment

Fluids ◽  
2020 ◽  
Vol 5 (2) ◽  
pp. 96
Author(s):  
Takao Oku ◽  
Hiroyuki Hirahara ◽  
Tomohiro Akimoto ◽  
Daiki Tsuchida
Keyword(s):  
Natural Frequency ◽  
Cfd Simulation ◽  
Low Frequency ◽  
Sound Emission ◽  
Breathing Mode ◽  
Bubble Deformation ◽  
Mode Oscillation ◽  
Computational Fluid Dynamics Cfd ◽  
Oscillation Frequencies ◽  
Air Column

When a bubble detaches from a nozzle immersed in water, a sound is emitted owing to the detachment. The bubble deformation and sound emission generated after detachment has been investigated in many studies, in which the breathing mode with a natural frequency was discussed based on the dynamics of the interface between the air and water. In this study, the deformation of a bubble was observed, and the sound emitted upon detachment was measured experimentally. To analyze the bubble deformation process, a computational fluid dynamics (CFD) simulation was conducted using the volume of fluid (VOF) method to predict the sound emission. In the analysis, the deformation behavior, the oscillation frequencies, sound pressure, and radius variation were discussed by comparing the numerical and experimental data. Furthermore, the natural frequency and low frequency vibrations were discussed based on the interference between the detached bubbles and the air column vibrations.

scholarly journals Mechanism of the Absent Air Column in Three Products Hydrocyclone Screen (TPHS): Experiment and Simulation

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 431
Author(s):  
Chuanzhen Wang ◽  
Anghong Yu ◽  
Zaisheng Zhu ◽  
Haizeng Liu ◽  
Md. Shakhaoath Khan
Keyword(s):  
Static Pressure ◽  
Cfd Simulation ◽  
Volume Fraction ◽  
Particle Separation ◽  
Physical Experiment ◽  
High Definition ◽  
Static Pressure Distribution ◽  
Cylindrical Screen ◽  
Computational Fluid Dynamics Cfd ◽  
Air Column

Three products hyrdrocyclone screen (TPHS) has been proposed for particle separation based on size. In TPHS, a cylindrical screen was embedded in a conventional hydrocyclone (CH) to combine the centrifugal classification and screening to particle separation based on size. The industrial application of TPHS indicates its better device performance than CH. Although, the earlier studies reveal some common understanding for TPHS, the information of the absent air column remains unknown. Hence, the combination of physical experiment and numerical simulation was considered involving a 75 mm TPHS for this knowledge gap. First, both the computational fluid dynamics (CFD) simulation with Reynolds stress mode and the physical experiment with a high-definition camera illustrate the development process details of a flow field in TPHS. That is, the water was imported along the tangential inlet into TPHS; then under the effects of the feed chamber wall and gravity, the liquid phase spiraled downward until the cylindrical screen passed through the sieve; as the liquid moved to the spigot, it could be discharged in time due to the small underflow port, thus the volume fraction of air rapidly reduced from 1 to 0; subsequently the water filled the TPHS and the absent air column could be observed. Furthermore, the distribution comparisons of air volume fraction and static pressure show that TPHS displayed the absent air core with the negative static pressure in the center region along the z-axis, while CH displayed the opposite features. In addition, despite the different inlet velocity, TPHS consistently presented the vanished air column which could be ascribed to the fact that the present cylindrical screen resulted in positive static pressure distribution inside TPHS.

scholarly journals Computational fluid dynamics (CFD) simulation analysis on retinal gas cover rates using computational eye models

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Makoto Gozawa ◽  
Yoshihiro Takamura ◽  
Tomoe Aoki ◽  
Kentaro Iwasaki ◽  
Masaru Inatani
Keyword(s):  
Cfd Simulation ◽  
Simulation Analysis ◽  
Fluid Dynamic ◽  
Fluid Analysis ◽  
Intraocular Gas ◽  
Pars Plana ◽  
Computational Fluid Dynamics Cfd ◽  
Multiple Breaks ◽  
Gas Volume ◽  
Wall Wettability

AbstractWe investigated the change in the retinal gas cover rates due to intraocular gas volume and positions using computational eye models and demonstrated the appropriate position after pars plana vitrectomy (PPV) with gas tamponade for rhegmatogenous retinal detachments (RRDs). Computational fluid dynamic (CFD) software was used to calculate the retinal wall wettability of a computational pseudophakic eye models using fluid analysis. The model utilized different gas volumes from 10 to 90%, in increments of 10% to the vitreous cavity in the supine, sitting, lateral, prone with closed eyes, and prone positions. Then, the gas cover rates of the retina were measured in each quadrant. When breaks are limited to the inferior retina anterior to the equator or multiple breaks are observed in two or more quadrants anterior to the equator, supine position maintained 100% gas cover rates in all breaks for the longest duration compared with other positions. When breaks are limited to either superior, nasal, or temporal retina, sitting, lower temporal, and lower nasal position were maintained at 100% gas cover rates for the longest duration, respectively. Our results may contribute to better surgical outcomes of RRDs and a reduction in the duration of the postoperative prone position.

scholarly journals Numerical and Experimental Investigation of Longitudinal Oscillations in Hall Thrusters

Aerospace ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 148
Author(s):  
Vittorio Giannetti ◽  
Manuel Martín Saravia ◽  
Luca Leporini ◽  
Simone Camarri ◽  
Tommaso Andreussi
Keyword(s):  
Discharge Current ◽  
Fluid Model ◽  
Low Frequency ◽  
Hall Thruster ◽  
Hall Thrusters ◽  
Current Signal ◽  
Plasma Parameters ◽  
Plasma Properties ◽  
Breathing Mode ◽  
Spatio Temporal

One of the main oscillatory modes found ubiquitously in Hall thrusters is the so-called breathing mode. This is recognized as a relatively low-frequency (10–30 kHz), longitudinal oscillation of the discharge current and plasma parameters. In this paper, we present a synergic experimental and numerical investigation of the breathing mode in a 5 kW-class Hall thruster. To this aim, we propose the use of an informed 1D fully-fluid model to provide augmented data with respect to available experimental measurements. The experimental data consists of two datasets, i.e., the discharge current signal and the local near-plume plasma properties measured at high-frequency with a fast-diving triple Langmuir probe. The model is calibrated on the discharge current signal and its accuracy is assessed by comparing predictions against the available measurements of the near-plume plasma properties. It is shown that the model can be calibrated using the discharge current signal, which is easy to measure, and that, once calibrated, it can predict with reasonable accuracy the spatio-temporal distributions of the plasma properties, which would be difficult to measure or estimate otherwise. Finally, we describe how the augmented data obtained through the combination of experiments and calibrated model can provide insight into the breathing mode oscillations and the evolution of plasma properties.

scholarly journals Numerical Investigation for the Resin Filling Behavior during Ultraviolet Nanoimprint Lithography of Subwavelength Moth-Eye Nanostructure

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 799
Author(s):  
Yuanchi Cui ◽  
Xuewen Wang ◽  
Chengpeng Zhang ◽  
Jilai Wang ◽  
Zhenyu Shi
Keyword(s):  
Simulation Model ◽  
Nanoimprint Lithography ◽  
Cfd Simulation ◽  
Boundary Slip ◽  
Accurate Analysis ◽  
Inlet Velocity ◽  
Filling Height ◽  
Proposed Model ◽  
Good Consistency ◽  
Computational Fluid Dynamics Cfd

Accurate analysis of the resin filling process into the mold cavity is necessary for the high-precision fabrication of moth-eye nanostructure using the ultraviolet nanoimprint lithography (UV-NIL) technique. In this research, a computational fluid dynamics (CFD) simulation model was proposed to reveal resin filling behavior, in which the effect of boundary slip was considered. By comparison with the experimental results, a good consistency was found, indicating that the simulation model could be used to analyze the resin filling behavior. Based on the proposed model, the effects of process parameters on resin filling behavior were analyzed, including resin viscosity, inlet velocity and resin thickness. It was found that the inlet velocity showed a more significant effect on filling height than the resin viscosity and thickness. Besides, the effects of boundary conditions on resin filling behavior were investigated, and it was found the boundary slip had a significant influence on resin filling behavior, and excellent filling results were obtained with a larger slip velocity on the mold side. This research could provide guidance for a more comprehensive understanding of the resin filling behavior during UV-NIL of subwavelength moth-eye nanostructure.

scholarly journals Computational Fluid Dynamics (CFD) Simulation on Mixing in T-Shaped Micromixer

2020 ◽  
Vol 932 ◽  
pp. 012006
Author(s):  
S N A Ahmad Termizi ◽  
C Y Khor ◽  
M A M Nawi ◽  
Nurlela Ahmad ◽  
Muhammad Ikman Ishak ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cfd Simulation ◽  
Computational Fluid Dynamics Cfd

Load Characteristics of Steel and Concrete Tubular Members Under Jet Fire: An Experimental and Numerical Study

2010 ◽  
Author(s):  
Jeong Hyo Park ◽  
Bong Ju Kim ◽  
Jung Kwan Seo ◽  
Jae Sung Jeong ◽  
Byung Keun Oh ◽  
...  
Keyword(s):  
Cfd Simulation ◽  
Numerical Study ◽  
Fire Load ◽  
Adiabatic Wall ◽  
Fire Engineering ◽  
Ansys Cfx ◽  
Design Values ◽  
Computational Fluid Dynamics Cfd ◽  
Load Characteristics ◽  
Set Up

The aim of this study was to evaluate the load characteristics of steel and concrete tubular members under jet fire, with the motivation to investigate the jet fire load characteristics in FPSO topsides. This paper is part of Phase II of the joint industry project on explosion and fire engineering of FPSOs (EFEF JIP) [1]. To obtain reliable load values, jet fire tests were carried out in parallel with a numerical study. Computational fluid dynamics (CFD) simulation was used to set up an adiabatic wall boundary condition for the jet fire to model the heat transfer mechanism. A concrete tubular member was tested under the assumption that there is no conduction effect from jet fire. A steel tubular member was tested and considered to transfer heat through conduction, convection, and radiation. The temperature distribution, or heat load, was analyzed at specific locations on each type of member. ANSYS CFX [2] and Kameleon FireEx [3] codes were used to obtain similar fire action in the numerical and experimental methods. The results of this study will provide a useful database to determine design values related to jet fire.

A Study on the Performance of Stratified Air Conditioning Design in Assembly Halls – A Case Study at the Dazhi Cultural Center in Taiwan

2013 ◽  
Vol 368-370 ◽  
pp. 599-602 ◽  
Author(s):  
Ian Hung ◽  
Hsien Te Lin ◽  
Yu Chung Wang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Indoor Air ◽  
Air Conditioning ◽  
Cfd Simulation ◽  
Indoor Temperature ◽  
Cultural Center ◽  
Computational Fluid Dynamics Cfd

This study focuses on the performance of air conditioning design at the Dazhi Cultural Center and uses a computational fluid dynamics (CFD) simulation to discuss the differences in wind velocity and ambient indoor temperature between all-zone air conditioning design and stratified air conditioning design. The results have strong implications for air conditioning design and can improve the indoor air quality of assembly halls.

Research on CFD Simulation of the Cement Slurry Mixer

2012 ◽  
Vol 621 ◽  
pp. 196-199
Author(s):  
Shui Ping LI ◽  
Ya Li Yuan ◽  
Lu Gang Shi
Keyword(s):  
Flow Field ◽  
High Performance ◽  
Cfd Simulation ◽  
Structural Parameters ◽  
Internal Flow ◽  
Simulation Method ◽  
Cement Slurry ◽  
Fluid Machinery ◽  
Computational Fluid Dynamics Cfd ◽  
Machinery Design

Numerical simulation method of the internal flow field of fluid machinery has become an important technology in the study of fluid machinery design. In order to obtain a high-performance cement slurry mixer, computational fluid dynamics (CFD) techniques are used to simulate the flow field in the mixer, and the simulation results are studied. According to the analysis results, the structural parameters of the mixer are modified. The results show the mixer under the revised parameters meet the design requirements well. So CFD analysis method can shorten design period and provide valuable theoretical guidance for the design of fluid machinery.

Sign in / Sign up

Export Citation Format

Share Document