scholarly journals Fabrication, Structure and Functional Characterizations of pH-Responsive Hydrogels Derived from Phytoglycogen

Foods ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 2653
Author(s):  
Xiuting Hu ◽  
Yao Liu ◽  
Yimei Chen ◽  
Tao Zhang ◽  
Ming Miao
Keyword(s):  
Electrostatic Repulsion ◽  
Swelling Ratio ◽  
Ph Responsive ◽  
X Ray Diffraction ◽  
Carrier System ◽  
Bioactive Substances ◽  
X Ray ◽  
Gelation Rate ◽  
Responsive Hydrogels ◽  
Scanning Electron

The pH-responsive hydrogels were obtained through successive carboxymethylation and phosphorylase elongatation of phytoglycogen and their structure and functional characterizations were investigated. Phytoglycogen (PG) was first carboxymethylated to obtain carboxymethyl phytoglycogen (CM-PG) with degree of substitution (DS) at 0.15, 0.25, 0.30, and 0.40, respectively. Iodine staining and X-ray diffraction analysis suggested that the linear glucan chains were successfully phosphorylase-elongated from the non-reducing ends at the CM-PG surface and assembled into the double helical segments, leading to formation of the hydrogel. The DS of CM-PG significantly influenced elongation of glucan chains. Specifically, fewer glucan chains were elongated for CM-PG with higher DS and the final glucan chains were shorter, resulting in lower gelation rate of chain-elongated CM-PG and lower firmness of the corresponding hydrogels. Scanning electron microscope observed that the hydrogels exhibited a porous and interconnected morphology. The swelling ratio and volume of hydrogels was low at pH 3–5 and then became larger at pH 6–8 due to electrostatic repulsion resulting from deprotonated carboxymethyl groups. Particularly, the hydrogel prepared from chain-elongated CM-PG (DS = 0.25) showed the highest sensitivity to pH. These results suggested that phosphorylase-treated CM-PG formed the pH-responsive hydrogel and that the elongation degree and the properties of hydrogels depended on the carboxymethylation degree. Thus, it was inferred that these hydrogels was a potential carrier system of bioactive substances for their targeted releasing in small intestine.

scholarly journals Using scanning electron microscopy, x-ray diffraction and IR spectroscopy to study the ageing of intumescent fire-proof coatings

2020 ◽  
Vol 29 (5) ◽  
pp. 60-70
Author(s):  
M. Yu. Umrikhina ◽  
T. O. Shorokhova ◽  
L. A. Pyankova ◽  
A. A. Kudryavtsev ◽  
S. V. Utkin
Keyword(s):  
Ir Spectroscopy ◽  
Service Life ◽  
Fire Resistance ◽  
Residual Life ◽  
Ammonium Polyphosphate ◽  
Swelling Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electron Microscopies ◽  
Scanning Electron

Introduction. The fire protection of metal structures is a relevant present-day problem; its solution implies better fire resistance performance of structures attainable through the application of intumescent fire-proof coatings whose service life expectancy is limited.Goals and objectives. Comprehensive studies of domestically made coating samples were performed to analyze the changes in the chemical composition of intumescent coatings containing ammonium polyphosphate, melamine, and pentaerythritol. The samples were exposed to artificial climatic ageing (3, 6, and 9 years). Methods. Optical and scanning electron microscopies were used to study the appearance of samples, the morphology of inclusions and the surface microstructure. X-ray diffraction and IR spectroscopy were employed to study the phase and structural states of samples, and the swelling ratio of fire-proof coatings was also examined.Results and discussion. It’s been found out that the swelling ratio of samples goes down to a significant extent as the time progresses, and when the residual life of a coating reaches 30 %, the fire resistance limit of the structure goes down. Sample ageing is the reason for gradual phase composition changes due to the melamine content reduction by 40 %, ammonium polyphosphate content reduction by 15 % and redistribution of other components that change the microstructure of coatings, as well as their fire retarding properties.Conclusions. The changes, influencing the ability of a coating to maintain its fire retarding efficiency as declared by the manufacturer, take place in the course of operation of a coating exposed to external factors. The regularities, identified by virtue of this research, can be used to study the samples taken at fire-proofed facilities to identify deviations from the initial condition of a coating and to forecast its actual service life.

scholarly journals Preparation and application of pH-responsive composite hydrogel beads as potential delivery carrier candidates for controlled release of berberine hydrochloride

2020 ◽  
Vol 7 (11) ◽  
pp. 200676
Author(s):  
Jiande Gao ◽  
Dongying Fan ◽  
Ping Song ◽  
Shudan Zhang ◽  
Xiong Liu
Keyword(s):  
Composite Hydrogel ◽  
Swelling Ratio ◽  
Ph Responsive ◽  
X Ray Diffraction ◽  
Swelling Properties ◽  
Pharmaceutical Dosage Forms ◽  
Berberine Hydrochloride ◽  
X Ray ◽  
Hydrogel Beads ◽  
Cumulative Release

For improving the effective concentration of berberine hydrochloride (BH) in the gastrointestinal tract, a series of pH-responsive hydrogel beads were prepared based on carboxymethylstarch-g-poly (acrylic acid)/palygorskite/starch/sodium alginate (CMS-g-PAA/PGS/ST/SA) in the present work. The developed hydrogel beads were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and thermogravimetric analysis (TG). Effect of palygorskite (PGS) content on the swelling properties of hydrogel beads and BH cumulative release were discussed. The pH responsiveness of hydrogel beads was also investigated in different media. Results illustrated that swelling of hydrogel beads and BH cumulative release from hydrogel beads were obviously affected by PGS content. The swelling ratio and BH cumulative release of composite hydrogel beads remarkably slowed down with PGS content increasing in the range from 10 to 40 wt%. The composite hydrogel beads were pH-responsive. At pH 7.4, the swelling ratio and BH cumulative release from composite hydrogel beads were the fastest among the dissolution media of pH 1.2, pH 6.8 and pH 7.4. The BH cumulative release from hydrogel beads was related to the swelling and relaxation of composite hydrogel beads and could be fitted better by the Higuchi model. The obtained composite hydrogel beads could be potentially used for the development of BH pharmaceutical dosage forms.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Sem and X-Ray Analysis of Renal and Biliary Calculi

1976 ◽  
Vol 34 ◽  
pp. 306-307
Author(s):  
R. J. Narconis ◽  
G. L. Johnson
Keyword(s):  
Chemical Constituents ◽  
Natural State ◽  
X Ray Diffraction ◽  
Chemical Methods ◽  
X Ray ◽  
Additional Dimension ◽  
Biliary Calculi ◽  
Calculus Formation ◽  
Scanning Electron

Analysis of the constituents of renal and biliary calculi may be of help in the management of patients with calculous disease. Several methods of analysis are available for identifying these constituents. Most common are chemical methods, optical crystallography, x-ray diffraction, and infrared spectroscopy. The application of a SEM with x-ray analysis capabilities should be considered as an additional alternative.A scanning electron microscope equipped with an x-ray “mapping” attachment offers an additional dimension in its ability to locate elemental constituents geographically, and thus, provide a clue in determination of possible metabolic etiology in calculus formation. The ability of this method to give an undisturbed view of adjacent layers of elements in their natural state is of advantage in determining the sequence of formation of subsequent layers of chemical constituents.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

Photocatalytic activity of TiO2 synthesized by anodization and anodic spark deposition

MRS Advances ◽  
2020 ◽  
Vol 5 (61) ◽  
pp. 3141-3152
Author(s):  
Alma C. Chávez-Mejía ◽  
Génesis Villegas-Suárez ◽  
Paloma I. Zaragoza-Sánchez ◽  
Rafael Magaña-López ◽  
Julio C. Morales-Mejía ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Surface Characteristics ◽  
Amorphous Solids ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Anodic Spark Oxidation ◽  
Porous Surfaces ◽  
Scanning Electron

AbstractSeveral photocatalysts, based on titanium dioxide, were synthesized by spark anodization techniques and anodic spark oxidation. Photocatalytic activity was determined by methylene blue oxidation and the catalytic activities of the catalysts were evaluated after 70 hours of reaction. Scanning Electron Microscopy and X Ray Diffraction analysis were used to characterize the catalysts. The photocatalyst prepared with a solution of sulfuric acid and 100 V presented the best performance in terms of oxidation of the dye (62%). The electric potential during the synthesis (10 V, low potential; 100 V, high potential) affected the surface characteristics: under low potential, catalyst presented smooth and homogeneous surfaces with spots (high TiO2 concentration) of amorphous solids; under low potential, catalyst presented porous surfaces with crystalline solids homogeneously distributed.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Sign in / Sign up

Export Citation Format

Share Document