scholarly journals Mechanical and Biocompatibility Properties of Calcium Phosphate Bioceramics Derived from Salmon Fish Bone Wastes

2020 ◽  
Vol 21 (21) ◽  
pp. 8082
Author(s):  
Merve Bas ◽  
Sibel Daglilar ◽  
Nilgun Kuskonmaz ◽  
Cevriye Kalkandelen ◽  
Gokce Erdemir ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Sintering Temperature ◽  
Biomedical Application ◽  
Calcium Phosphates ◽  
Biological Properties ◽  
Fish Bone ◽  
Calcination Process ◽  
In Vitro Biocompatibility ◽  
Different Temperatures

Natural calcium phosphates derived from fish wastes are a promising material for biomedical application. However, their sintered ceramics are not fully characterized in terms of mechanical and biological properties. In this study, natural calcium phosphate was synthesized through a thermal calcination process from salmon fish bone wastes. The salmon-derived calcium phosphates (sCaP) were sintered at different temperatures to obtain natural calcium phosphate bioceramics and then were investigated in terms of their microstructure, mechanical properties and biocompatibility. In particular, this work is concerned with the effects of grain size on the relative density and microhardness of the sCaP bioceramics. Ca/P ratio of the sintered sCaP ranged from 1.73 to 1.52 when the sintering temperature was raised from 1000 to 1300 °C. The crystal phase of all the sCaP bioceramics obtained was biphasic and composed of hydroxyapatite (HA) and tricalcium phosphate (TCP). The density and microhardness of the sCaP bioceramics increased in the temperature interval 1000–1100 °C, while at temperatures higher than 1100 °C, these properties were not significantly altered. The highest compressive strength of 116 MPa was recorded for the samples sintered at 1100 °C. In vitro biocompatibility was also examined in the behavior of osteosarcoma (Saos-2) cells, indicating that the sCaP bioceramics had no cytotoxicity effect. Salmon-derived biphasic calcium phosphates (BCP) have the potential to contribute to the development of bone substituted materials.

PRECIPITATION CONTROL AND MECHANICAL PROPERTY OF CALCIUM PHOSPHATE–COATED AZ31B ALLOY FOR BIOMEDICAL APPLICATION

2011 ◽  
Vol 23 (03) ◽  
pp. 193-203 ◽  
Author(s):  
Qiang Wang ◽  
Lili Tan ◽  
Qiang Zhang ◽  
Jianhong Qiu ◽  
Ke Yang
Keyword(s):  
Magnesium Alloy ◽  
Calcium Phosphate ◽  
Electrochemical Impedance ◽  
Biomedical Application ◽  
Early Stage ◽  
Calcium Phosphates ◽  
Chemical Deposition ◽  
Biological Properties ◽  
Calcium Phosphate Coating ◽  
Az31b Alloy

Surface modification is believed to be an effective way to control the biodegradation rate of magnesium alloys and improve their biological properties. In the present work, a calcium phosphate (Ca-P) coating was prepared on the AZ31B magnesium alloy by a chemical deposition method to integrate the mechanical advantages of the magnesium substrate and the good bioactivity of the ceramic coating. It was shown that the coating was mainly composed of magnesium and calcium phosphates. Scanning electron microscope coupled with the energy dispersive spectrum analyses showed that rough and crystallined Ca-P coatings with different Ca/P ratios and thickness were formed on the alloy by variation of deposition time. The corrosion resistance of AZ31B alloy was significantly improved by the Ca-P coating. Electrochemical impedance spectroscopy test was used to illustrate the reaction process of Ca-P coating on the alloy. Upon the above results, Ca-P formation mechanism on the AZ31B alloy was proposed. The heterogeneous nucleation and growth of the calcium phosphate coating may be catalyzed by the anodic dissolution of the magnesium alloy substrate in the early stage of deposition, and the deposition coating is mainly composed of the magnesium phosphate. Then calcium phosphate deposition on the alloy becomes dominant with the increase of time. Tensile test in simulated body environment results showed that the time of fracture and ultimate tensile strength for the coated AZ31B Mg alloy were higher than those of the uncoated, which is beneficial in supporting fractured bone for a longer time.

Growth of Calcium Phosphate Coating on Ti-7.5Mo Alloy after Anodic Oxidation

2013 ◽  
Vol 334-335 ◽  
pp. 297-302 ◽  
Author(s):  
A.L.A. Escada ◽  
João Paulo Barros Machado ◽  
Roberto Zenhei Nakazato ◽  
Ana Paula Rosifini Alves Claro
Keyword(s):  
Calcium Phosphate ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Calcium Phosphates ◽  
Sodium Titanate ◽  
Ammonium Fluoride ◽  
Biological Properties ◽  
Calcium Phosphate Coating ◽  
Phosphate Coating

Titanium and its alloys are widely used as biomaterials due to their mechanical, chemical and biological properties. To enhance the biocompatibility of titanium alloys, various surface treatments have been proposed. In particular, the formation of titanium oxide nanotubes layers has been extensively examined. Among the various materials for implants, calcium phosphates and hydroxyapatite are widely used clinically. In this work, titanium nanotubes were fabricated on the surface of Ti-7.5Mo alloy by anodization. The samples were anodized for 20 V in an electrolyte containing glycerol in combination with ammonium fluoride (NH4F, 0.25%), and the anodization time was 24 h. After being anodized, specimens were heat treated at 450 °C and 600°C for 1 h to crystallize the amorphous TiO2 nanotubes and then treated with NaOH solution to make them bioactive, to induce growth of calcium phosphate in a simulated body fluid. Surface morphology and coating chemistry were obtained respectively using, field-emission scanning electron microscopy (FEG-SEM), AFM and X-ray diffraction (XRD). It was shown that the presence of titanium nanotubes induces the growth of a sodium titanate nanolayer. During the subsequent in-vitro immersion in a simulated body fluid, the sodium titanate nanolayer induced the nucleation and growth of nanodimensioned calcium phosphate. It was possible to observe the formation of TiO2 nanotubes on the surface of Ti-7.5Mo. Calcium phosphate coating was greater in the samples with larger nanotube diameter. These findings represent a simple surface treatment for Ti-7.5Mo alloy that has high potential for biomedical applications.

scholarly journals Development, Characterization and In Vitro Biological Properties of Scaffolds Fabricated From Calcium Phosphate Nanoparticles

2019 ◽  
Vol 20 (7) ◽  
pp. 1790 ◽  
Author(s):  
Lizette Morejón ◽  
José Angel Delgado ◽  
Alexandre Antunes Ribeiro ◽  
Marize Varella de Oliveira ◽  
Eduardo Mendizábal ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mineral Composition ◽  
Cell Attachment ◽  
Sintering Temperature ◽  
Calcium Phosphates ◽  
Total Porosity ◽  
Biological Properties ◽  
Solid Content ◽  
Native Bone

Ceramic materials mimic the mineral composition of native bone and feature osteoconductive properties; they are therefore used to regenerate bone tissue. Much research focuses on increasing the porosity and pore interconnectivity of ceramic scaffolds to increase osteoconductivity, cell migration and cell-cell interaction. We aimed to fabricate biocompatible 3D-scaffolds featuring macro- and microporous calcium phosphates with high pore interconnection. Nanoparticles of hydroxyapatite (HA) and calcium deficient hydroxyapatite (CDHA) were synthesized by wet chemical precipitation. Scaffolds were produced from them by the replication polymeric foam technique. Solid content and sintering temperature were varied. Nanoparticles and scaffolds were characterized regarding morphology, chemical and mineral composition, porosity and mechanical properties. Biocompatibility, cell attachment and distribution were evaluated in vitro with human adipose mesenchymal stem cells. Scaffolds with total porosity of 71%–87%, pores in the range of 280–550 µm and connectivity density up to 43 mm−3 were obtained. Smaller pore sizes were obtained at higher sintering temperature. High solid content resulted in a decrease of total porosity but increased interconnectivity. Scaffolds 50HA/50β-TCP featured superior interconnectivity and mechanical properties. They were bioactive and biocompatible. High HA solid content (40 wt.%) in the HA pure scaffolds was negative for cell viability and proliferation, while in the 50HA/50β-TCP composite scaffolds it resulted more biocompatible.

scholarly journals Physico-chemical–mechanical and in vitro biological properties of calcium phosphate cements with doped amorphous calcium phosphates

Biomaterials ◽  
2007 ◽  
Vol 28 (6) ◽  
pp. 956-965 ◽  
Author(s):  
Marion Julien ◽  
Ibrahim Khairoun ◽  
Racquel Z. LeGeros ◽  
Severine Delplace ◽  
Paul Pilet ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Calcium Phosphates ◽  
Biological Properties ◽  
Calcium Phosphate Cements ◽  
Physico Chemical

Synthesis, Characterization and In Vitro Evaluation of Strontium-Containing Sol-Gel Derived Bioactive Glass/ Biphasic Calcium Phosphate Nanocomposite

2013 ◽  
Vol 467 ◽  
pp. 64-69 ◽  
Author(s):  
Nader Nezafati ◽  
Saeed Hesaraki ◽  
Mohammad-Reza Badr-Mohammadi
Keyword(s):  
Calcium Phosphate ◽  
Bioactive Glass ◽  
Biphasic Calcium Phosphate ◽  
Bending Strength ◽  
Sol Gel ◽  
Physical And Mechanical Properties ◽  
Sharp Decrease ◽  
Biological Properties ◽  
Different Temperatures

In the present research, strontium containing nanobioactive glass (NBG-Sr) was synthesized by sol-gel method. The morphology was analyzed by transmission electron microscope (TEM). Different amounts (0.5 to 5 wt%) of NBG-Sr were then added to biphasic calcium phosphate (BCP). They were sintered at different temperatures, i.e., 1100, 1200 and 1300 °C and changes in physical and mechanical properties were investigated. A sharp decrease in pore volume was observed as the temperature increased. The maximum bending strength (~45 MPa) was achieved for BCP which was mixed with 3 wt% NBG-Sr and sintered at 1200 °C. This value was approximately the same when it was sintered at 1300 °C. The bending strength failed when both lower and higher amounts of 3 wt% NBG-Sr were utilized. Therefore, sintering of composites at 1200 °C was economically reasonable. The X-ray results showed that NBG-Sr additive did not change the phase composition of BCP when it was heat treated at 1200 °C. The attachment and proliferation of rat calvarium-derived osteoblasts on samples sintered at 1200 °C were also evaluated by scanning electron microscopy (SEM). Based on cell studies, all NBG-Sr-added BCPs supported attachment and proliferation of osteoblastic cells. Overall, biphasic calcium phosphate materials with improved mechanical and biological properties can be produced by using certain quantity of strontium-containing bioactive glass particles.

scholarly journals Octacalcium Phosphate for Bone Tissue Engineering: Synthesis, Modification, and In Vitro Biocompatibility Assessment

2021 ◽  
Vol 22 (23) ◽  
pp. 12747
Author(s):  
Anastasia Yu. Teterina ◽  
Igor V. Smirnov ◽  
Irina S. Fadeeva ◽  
Roman S. Fadeev ◽  
Polina V. Smirnova ◽  
...  
Keyword(s):  
Low Temperature ◽  
Bone Tissue ◽  
Bone Repair ◽  
Calcium Phosphates ◽  
Normal Pressure ◽  
Octacalcium Phosphate ◽  
Biological Properties ◽  
In Vitro Biocompatibility ◽  
Ionic Substitution

Octacalcium phosphate (OCP, Ca8H2(PO4)6·5H2O) is known to be a possible precursor of biological hydroxyapatite formation of organic bone tissue. OCP has higher biocompatibility and osseointegration rate compared to other calcium phosphates. In this work, the synthesis of low-temperature calcium phosphate compounds and substituted forms of those at physiological temperatures is shown. Strontium is used to improve bioactive properties of the material. Strontium was inserted into the OCP structure by ionic substitution in solutions. The processes of phase formation of low-temperature OCP with theoretical substitution of strontium for calcium up to 50 at.% in conditions close to physiological, i.e., temperature 35–37 °C and normal pressure, were described. The effect of strontium substitution range on changes in the crystal lattice of materials, the microstructural features, surface morphology and biological properties in vitro has been established. The results of the study indicate the effectiveness of using strontium in OCP for improving biocompatibility of OCP based composite materials intended for bone repair.

scholarly journals Amorphous–Crystalline Calcium Phosphate Coating Promotes In Vitro Growth of Tumor-Derived Jurkat T Cells Activated by Anti-CD2/CD3/CD28 Antibodies

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3693
Author(s):  
Yurii P. Sharkeev ◽  
Ekaterina G. Komarova ◽  
Valentina V. Chebodaeva ◽  
Mariya B. Sedelnikova ◽  
Aleksandr M. Zakharenko ◽  
...  
Keyword(s):  
T Cells ◽  
Calcium Phosphate ◽  
Biological Effects ◽  
Electrical Potential ◽  
Biological Properties ◽  
Modern Trend ◽  
Calcium Phosphate Coating ◽  
Jurkat T Cells ◽  
Micro Arc Oxidation

A modern trend in traumatology, orthopedics, and implantology is the development of materials and coatings with an amorphous–crystalline structure that exhibits excellent biocopatibility. The structure and physico–chemical and biological properties of calcium phosphate (CaP) coatings deposited on Ti plates using the micro-arc oxidation (MAO) method under different voltages (200, 250, and 300 V) were studied. Amorphous, nanocrystalline, and microcrystalline statesof CaHPO4 and β-Ca2P2O7were observed in the coatings using TEM and XRD. The increase in MAO voltage resulted in augmentation of the surface roughness Ra from 2.5 to 6.5 µm, mass from 10 to 25 mg, thickness from 50 to 105 µm, and Ca/P ratio from 0.3 to 0.6. The electrical potential (EP) of the CaP coatings changed from −456 to −535 mV, while the zeta potential (ZP) decreased from −53 to −40 mV following an increase in the values of the MAO voltage. Numerous correlations of physical and chemical indices of CaP coatings were estimated. A decrease in the ZP magnitudes of CaP coatings deposited at 200–250 V was strongly associated with elevated hTERT expression in tumor-derived Jurkat T cells preliminarily activated with anti-CD2/CD3/CD28 antibodies and then contacted in vitro with CaP-coated samples for 14 days. In turn, in vitro survival of CD4+ subsets was enhanced, with proinflammatory cytokine secretion of activated Jurkat T cells. Thus, the applied MAO voltage allowed the regulation of the physicochemical properties of amorphous–crystalline CaP-coatings on Ti substrates to a certain extent. This method may be used as a technological mechanism to trigger the behavior of cells through contact with micro-arc CaP coatings. The possible role of negative ZP and Ca2+ as effectors of the biological effects of amorphous–crystalline CaP coatings is discussed. Micro-arc CaP coatings should be carefully tested to determine their suitability for use in patients with chronic lymphoid malignancies.

scholarly journals A Review on the Enhancement of Calcium Phosphate Cement with Biological Materials in Bone Defect Healing

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3075
Author(s):  
Sok Kuan Wong ◽  
Yew Hoong Wong ◽  
Kok-Yong Chin ◽  
Soelaiman Ima-Nirwana
Keyword(s):  
Calcium Phosphate ◽  
Calcium Phosphate Cement ◽  
Research Effort ◽  
Biological Materials ◽  
Biological Properties ◽  
Comprehensive Overview ◽  
Bone Defect Healing ◽  
Living Organisms

Calcium phosphate cement (CPC) is a promising material used in the treatment of bone defects due to its profitable features of self-setting capability, osteoconductivity, injectability, mouldability, and biocompatibility. However, the major limitations of CPC, such as the brittleness, lack of osteogenic property, and poor washout resistance, remain to be resolved. Thus, significant research effort has been committed to modify and reinforce CPC. The mixture of CPC with various biological materials, defined as the materials produced by living organisms, have been fabricated by researchers and their characteristics have been investigated in vitro and in vivo. This present review aimed to provide a comprehensive overview enabling the readers to compare the physical, mechanical, and biological properties of CPC upon the incorporation of different biological materials. By mixing the bone-related transcription factors, proteins, and/or polysaccharides with CPC, researchers have demonstrated that these combinations not only resolved the lack of mechanical strength and osteogenic effects of CPC but also further improve its own functional properties. However, exceptions were seen in CPC incorporated with certain proteins (such as elastin-like polypeptide and calcitonin gene-related peptide) as well as blood components. In conclusion, the addition of biological materials potentially improves CPC features, which vary depending on the types of materials embedded into it. The significant enhancement of CPC seen in vitro and in vivo requires further verification in human trials for its clinical application.

scholarly journals Organic/Inorganic bioactive materials Part III: in vitro bioactivity of gelatin/silicocarnotite hybrids

2009 ◽  
Vol 7 (4) ◽  
pp. 721-730 ◽  
Author(s):  
Lachezar Radev ◽  
Maria Fernandes ◽  
Isabel Salvado ◽  
Daniela Kovacheva
Keyword(s):  
Calcium Phosphate ◽  
Hybrid Materials ◽  
Calcium Phosphates ◽  
Ceramic Powder ◽  
Structure Evolution ◽  
In Vitro Test ◽  
In Vitro Bioactivity ◽  
Bioactive Materials ◽  
Vitro Test

AbstractIn this work we present our experimental results on synthesis, structure evolution and in vitro bioactivity assessment of new gelatin/silicocarnotite hybrid materials. The hybrids were obtained by diluting gelatin (G) and silicocarnotite (S) ceramic powder with G:S ratios of 75:25 and 25:75 wt.% in hot (40°C) water. The hybrids were characterized using XRD, FTIR, SEM/EDS and XPS. FTIR depicts that the “red shift” of amide I and COO− could be attributed to the fact that the gelatin prefers to chelate Ca2+ from S. The growth of calcium phosphates on the surface of the hybrids synthesized and then immersed in 1.5 SBF for 3 days was studied by using of FTIR, XRD and SEM/EDS. According to FTIR results, after an immersion of 3 days, A and B-type CO3HA can be observed on the surface. XRD results indicate the presence of hydroxyapatite with well defined crystallinity. SEM/EDS of the precipitated layers show the presence of CO3HA and amorphous calcium phosphate on the surface of samples with different G/S content when immersed in 1.5 SBF. XPS of the G/S hybrid with 25:75 wt.% proved the presence of Ca-deficient hydroxyapatite after an in vitro test for 3 days.

Sign in / Sign up

Export Citation Format

Share Document