scholarly journals A Casing Treatment with Axial Grooves for Centrifugal Compressors

2019 ◽  
Vol 4 (3) ◽  
pp. 27 ◽  
Author(s):  
Sebastian Leichtfuß ◽  
Johannes Bühler ◽  
Heinz-Peter Schiffer ◽  
Patrick Peters ◽  
Michael Hanna
Keyword(s):  
Pressure Ratio ◽  
Peak Efficiency ◽  
Centrifugal Compressors ◽  
Reduced Pressure ◽  
Casing Treatment ◽  
Operating Range ◽  
High Pressure Compressor ◽  
Working Principle ◽  
Past Experiences ◽  
Pressure Compressor

This paper provides an investigation of a casing treatment (CT) approach for pressure ratio improvements of centrifugal compressors between peak efficiency and surge. Results were experimentally verified for a variety of automotive turbocharger compressors and analyzed with 3D CFD. The CT design is an adaptation from an axial high-pressure compressor, which was successfully applied and intensively investigated in recent years. The aerodynamic working principle of the applied CT design and the achievable improvements are shown and described. The demand of operating range for automotive applications typically dictates high inlet shroud to outlet radius ratio (high trim) and past experiences indicate that a recirculation zone is formed in the inducer for those centrifugal compressors. This recirculation at the inlet shroud causes losses, a massive blockage and induces a co-rotating swirl at the inlet of the impeller. The result is a reduced pressure ratio, often leading to flat speed lines between the onset of recirculation and surge. This paper provides an understanding of inducer recirculation, its impacts and suggests countermeasures. The CT design for centrifugal compressors only influences flow locally at the inducer and prevents recirculation. It differs substantially in design and functionality from the classical bleed slot system commonly used to increase operating range. An experimental and CFD comparison between these designs is presented. While the classical bleed slot system often provides a massive increase in operating range, it often fails to increase the pressure ratio between onset of inducer recirculation and surge. In contrast, the CT design achieves a gain in pressure ratio near surge.

scholarly journals Stall Margin Improvement in a Centrifugal Compressor through Inducer Casing Treatment

2016 ◽  
Vol 2016 ◽  
pp. 1-19
Author(s):  
V. V. N. K. Satish Koyyalamudi ◽  
Quamber H. Nagpurwala
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Treatment Technique ◽  
Centrifugal Compressors ◽  
Stall Margin ◽  
Casing Treatment ◽  
Operating Range ◽  
Stable Operating ◽  
Stall Margin Improvement

The increasing trend of high stage pressure ratio with increased aerodynamic loading has led to reduction in stable operating range of centrifugal compressors with stall and surge initiating at relatively higher mass flow rates. The casing treatment technique of stall control is found to be effective in axial compressors, but very limited research work is published on the application of this technique in centrifugal compressors. Present research was aimed to investigate the effect of casing treatment on the performance and stall margin of a high speed, 4 : 1 pressure ratio centrifugal compressor through numerical simulations using ANSYS CFX software. Three casing treatment configurations were developed and incorporated in the shroud over the inducer of the impeller. The predicted performance of baseline compressor (without casing treatment) was in good agreement with published experimental data. The compressor with different inducer casing treatment geometries showed varying levels of stall margin improvement, up to a maximum of 18%. While the peak efficiency of the compressor with casing treatment dropped by 0.8%–1% compared to the baseline compressor, the choke mass flow rate was improved by 9.5%, thus enhancing the total stable operating range. The inlet configuration of the casing treatment was found to play an important role in stall margin improvement.

An Investigation of the Use of Wet Compression in Industrial Centrifugal Compressors

2006 ◽  
Author(s):  
Ahmed Abdelwahab
Keyword(s):  
Pressure Ratio ◽  
Water Injection ◽  
Centrifugal Compressors ◽  
Power Requirement ◽  
Operating Range ◽  
Multi Stage ◽  
Direct Water Injection ◽  
Compressor Inlet ◽  
Wet Compression ◽  
Compressor Power

Industrial centrifugal compressors generally comprise a number of low pressure ratio intercooled stages. This is done primarily for the purpose of reducing the compressor power requirements and improving the operating range of the multi-stage compressor. In recent years, however, rapid increases in the per-kilowatt-hour prices both domestically and worldwide has led to renewed research efforts to further reduce the power requirements of this type of compression equipment. Several attempts have been made to use direct water injection as a means to overspray the compressor inlet to further reduce its power requirement. This paper presents an investigation into the use of this technology in industrial centrifugal compressors. A simple numerical method is presented for the computation of wet compression processes. The method is based on both droplet evaporation and compressor mean-line calculations. An assessment, based on the developed model, of the effectiveness of evaporative processes in reducing the compressor power consumption per stage is presented. The impacts on stage efficiency and operating range are also presented.

Impact of Main and Splitter Blade Leading Edge Contour on the Performance of High Pressure Ratio Centrifugal Compressors

2014 ◽  
Author(s):  
Rodrigo R. Erdmenger ◽  
Vittorio Michelassi
Keyword(s):  
High Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Centrifugal Compressors ◽  
Operating Range ◽  
High Pressure Ratio ◽  
The Impact ◽  
Blade Leading Edge

The impact of leading edge sweep in an attempt to reduce shock losses and extend the stall margin on axial compressors has been extensively studied, however only a few studies have looked at understanding the impact of leading edge contouring on the performance of centrifugal compressors. The present work studies the impact of forward and aft sweep on the main and splitter blade leading edge of a generic high flow coefficient and high pressure ratio centrifugal compressor design and the impact on its overall peak efficiency, pressure ratio and operating range. The usage of aft sweep on the main blade led to an increase of the pressure ratio and efficiency, however it also led to a reduction of the stable operating range of the impeller analyzed. The forward sweep cases analyzed where the tip leading edge was displaced axially forward showed a slight increase in pressure ratio, and a significant increase on operating range. The impact of leading edge sweep on the sensitivity of the impeller performance to tip clearance was also studied. The impeller efficiency was found to be less sensitive to an increase of tip clearance for both aft and forward sweep cases studied. The forward sweep cases studied also showed a reduced sensitivity from operating range to tip clearance. The studies conducted on the splitter leading edge profile indicate that aft sweep may help to increase the operating range of the impeller analyzed by up to 16% while maintaining similar pressure ratio and efficiency characteristics of the impeller. The improvement of operating range obtained with the leading edge forward sweep and splitter aft sweep was caused by a reduction of the interaction of the tip vortex of the main blade with the splitter tip, and a reduction of the blockage caused by this interaction.

An Investigation of Centrifugal Compressor Stability Enhancement Using a Novel Vaned Diffuser Recirculation Technique

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Lee Galloway ◽  
Daniel Rusch ◽  
Stephen Spence ◽  
Klemens Vogel ◽  
René Hunziker ◽  
...  
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Vaned Diffuser ◽  
Casing Treatment ◽  
Operating Range ◽  
Stable Operating ◽  
Mass Flow Rates ◽  
Low Mass ◽  
Casing Treatments

The main centrifugal compressor performance criteria are pressure ratio, efficiency, and wide flow range. The relative importance of these criteria, and therefore the optimum design balance, varies between different applications. Vaned diffusers are generally used for high-performance applications as they can achieve higher efficiencies and pressure ratios, but have a reduced operating range, in comparison to vaneless diffusers. Many impeller-based casing treatments have been developed to enlarge the operating range of centrifugal compressors over the last decades but there is much less information available in open literature for diffuser focused methods, and they are not widely adopted in commercial compressor stages. The development of aerodynamic instabilities at low mass flow rate operating conditions can lead to the onset of rotating stall or surge, limiting the stable operating range of the centrifugal compressor stage. More understanding of these aerodynamic instabilities has been established in recent years. Based on this additional knowledge, new casing treatments can be developed to prevent or suppress the development of these instabilities, thus increasing the compressor stability at low mass flow rates. This paper presents a novel vaned diffuser casing treatment that successfully increased the stable operating range at low mass flow rates and high pressure ratios. Detailed experimental measurements from a high pressure ratio turbocharger compressor stage combined with complementary CFD simulations were used to examine the effect of the new diffuser casing treatment on the compressor flow field and led to the improvement in overall compressor stability. A detailed description of how the new casing treatment operates is presented within the paper.

Unsteady Measurements of Periodic Effects in a Transonic Compressor With Casing Treatments

2015 ◽  
Author(s):  
Christoph Brandstetter ◽  
Fabian Wartzek ◽  
Jan Werner ◽  
Heinz-Peter Schiffer ◽  
Frank Heinichen
Keyword(s):  
High Speed ◽  
Operating Conditions ◽  
Reference Case ◽  
Stall Inception ◽  
Casing Treatment ◽  
Operating Range ◽  
Transonic Compressor ◽  
High Pressure Compressor ◽  
Blade Tip ◽  
Casing Treatments

Application of non-axisymmetric Casing Treatments (CTs) can extend the operating range of a transonic compressor significantly. Recent CT designs have proven successful at achieving operating range extension without efficiency loss under design conditions. Two different CT designs were investigated on a high-speed one and a half stage test rig using extensive instrumentation. The stage setup is representative of the front stage of a modern high-pressure compressor. Results of Particle Image Velocimetry (PIV) measurements taken in the blade tip region underneath the Casing Treatment show a significantly modified flow structure compared to the Smooth Casing reference case. Blockage zone, secondary flow and shock structures are affected by the CT, especially in highly throttled operating conditions. The stall inception process of the system with Axial Slots shows unexpected behavior, with modal activities that are not observed without CT. These activities are resolved using unsteady wall pressure and Hot Wire measurements.

An Experimental Investigation About the Effect of the Partial Casing Treatment on a Transonic Axial-Flow Compressor Performance Under Inlet Distortion

2012 ◽  
Author(s):  
Maoyi Li ◽  
Wei Yuan ◽  
Xizhen Song ◽  
Yajun Lu ◽  
Zhiping Li ◽  
...  
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Peak Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Inlet Distortion ◽  
Flow Compressor ◽  
Total Pressure Ratio

The traditional annulus casing treatment often pays the price of lowered efficiency for improving the stall margin of a compressor under inlet distortion. In view of the unsymmetry of the inlet flow-field of compressors, partial casing treatment was used to control the flow in a transonic axial-flow compressor with arc-skewed-slots deployed at different circumferential positions under inlet distortion. The experimental results indicate that when the partial casing treatment is arranged on the undistorted and distorted sectors, the stall margin is enhanced by 8.02%, with the relative peak efficiency improved simultaneously by 2.143%, compared with the case of solid casing at 98% rotating speed. By contrast, the traditional casing treatment increases the stall-margin by 23.13%, but decreases the relative peak efficiency by 0.752%. By analyzing dynamic and static experimental data, the mechanism underlying the partial casing treatment was also studied in detail here. The disturbances of inlet flow were restrained by annulus casing treatment, nevertheless the total pressure ratio was decreased obviously in the distorted sector. As a result, the stall-margin is improved, but the relative peak efficiency is decreased too. When the partial casing treatment was arranged on the undistortded and distorted sectors, the stall disturbances was thereby restrained. So the stall margin was enhanced. In addition, the total pressure ratio was improved by the partial casing treatment in the distorted and transition sectors, and thus the relative peak efficiency was also increased markedly.

Meanline Modeling of Inlet Recirculation in Automotive Turbocharger Centrifugal Compressors

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Peter Harley ◽  
Stephen Spence ◽  
Dietmar Filsinger ◽  
Michael Dietrich ◽  
Juliana Early
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Flow Coefficient ◽  
Centrifugal Compressors ◽  
Flow Paths ◽  
Operating Range ◽  
Recirculating Flow ◽  
Modeling Approach ◽  
Mass Flow Rates ◽  
Compressor Map

This study provides a novel meanline modeling approach for centrifugal compressors. All compressors analyzed are of the automotive turbocharger variety and have typical upstream geometry with no casing treatments or preswirl vanes. Past experience dictates that inducer recirculation is prevalent toward surge in designs with high inlet shroud to outlet radius ratios; such designs are found in turbocharger compressors due to the demand for operating range. The aim of the paper is to provide further understanding of impeller inducer flow paths when operating with significant inducer recirculation. Using three-dimensional (3D) computational fluid dynamics (CFD) and a single-passage model, the flow coefficient at which the recirculating flow begins to develop and the rate at which it grows are used to assess and correlate work and angular momentum delivered to the incoming flow. All numerical modeling has been fully validated using measurements taken from hot gas stand tests for all compressor stages. The new modeling approach links the inlet recirculating flow and the pressure ratio characteristic of the compressor. Typically for a fixed rotational speed, between choke and the onset of impeller inlet recirculation the pressure ratio rises gradually at a rate dominated by the aerodynamic losses. However, in modern automotive turbocharger compressors where operating range is paramount, the pressure ratio no longer changes significantly between the onset of recirculation and surge. Instead the pressure ratio remains relatively constant for reducing mass flow rates until surge occurs. Existing meanline modeling techniques predict that the pressure ratio continues to gradually rise toward surge, which when compared to test data is not accurate. A new meanline method is presented here which tackles this issue by modeling the direct effects of the recirculation. The result is a meanline model that better represents the actual fluid flow seen in the CFD results and more accurately predicts the pressure ratio and efficiency characteristics in the region of the compressor map affected by inlet recirculation.

Casing Treatment of Centrifugal Compressors

2015 ◽  
Author(s):  
Jisha Noushad ◽  
Anand Babu Dhamarla ◽  
Pavan Kumar
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Reverse Flow ◽  
Pressure Fluctuations ◽  
Centrifugal Compressors ◽  
Flow Rates ◽  
Casing Treatment ◽  
Operating Range ◽  
Mass Flow Rates ◽  
Ported Shroud

The operating range of any compressor is controlled by Surge and Choke. Surge occurs at lower mass flow rates with large pressure fluctuations and flow reversals, while choke occurs at higher mass flow rates when the flow rate reaches the limit which compressor can discharge. Ported shroud is a cost effective casing treatment that can greatly improve operating range of centrifugal compressors. By removing the stagnant and reverse flow from shroud wall boundary-layer region and recirculating it to impeller inlet, it has been demonstrated that larger range of operability can be achieved without much loss on compressor efficiency. This paper demonstrates the improvement of a centrifugal compressor operational range with ported shroud configuration. A series of CFD simulations were carried out with open source centrifugal compressor geometry (NASA HPCC 4:1) to create performance characteristics/speed-lines. The CFD methodology and practices were validated by comparing the results with the experimental data. Performance evaluation of ported shroud configuration is done with respect to solid shroud. Ported shroud compressor is proven to give higher choke mass flow and also a better surge margin compared to the Solid shroud model. The phenomena of in-flowing and out-flowing port have also been demonstrated. Emphasis was given to understand how ported shroud helps to achieve a better performance. A design optimization study has also been carried out in order to establish the optimum ported shroud configuration. Design parameter such as port location has been selected and the effect of this parameter on the performance of the compressor is studied using CFD. Optimum port geometry was proposed.

The Development of Centrifugal Compressor Impeller

2008 ◽  
Author(s):  
C. Xu ◽  
R. S. Amano
Keyword(s):  
Centrifugal Compressor ◽  
State Of The Art ◽  
Pressure Ratio ◽  
Structure Design ◽  
Centrifugal Compressors ◽  
Rotating Speed ◽  
Operating Range ◽  
High Pressure Ratio ◽  
Current State ◽  
Compressor Impeller

Impeller is one of the key components of industrial centrifugal compressors and turbochargers. Aerodynamic and structure designs of the impeller are critical to the success of the whole compressor stages. The requirements for efficiency and operating range of industrial centrifugal compressors and turbochargers have been increased dramatically compared with the situation in the past. The efficiency of newly developed low-pressure ratio centrifugal compressor has reached the possible level of the machine. However, the efficiency level of intermediate and high-pressure ratio machine still have gap between the current state-of-the-art and possible level. The challenge for centrifugal compressor design is to keep the efficiency level at state-of-the-art and increase the compressor operating range. Increase of the compressor operating range without sacrificing compressor peak efficiency is difficult to achieve. The product globalization requires one product design, which can be used in all locations. In some counties, due to the technology differences, electricity frequencies variations could be 10%. Turbocharger compressors work at different rotational speeds for majority of the time. The compressor impeller rotating speeds change in certain range. The impeller rotating speed variation makes the impeller structure design more challenging. In this study, a full-3D impeller was designed to optimize impeller aerodynamic performance and structure characteristics.

Sign in / Sign up

Export Citation Format

Share Document