scholarly journals Improved Bioactivity of 3D Printed Porous Titanium Alloy Scaffold with Chitosan/Magnesium-Calcium Silicate Composite for Orthopaedic Applications

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 203 ◽  
Author(s):  
Chun-Hao Tsai ◽  
Chih-Hung Hung ◽  
Che-Nan Kuo ◽  
Cheng-Yu Chen ◽  
Yu-Ning Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Calcium Silicate ◽  
Cell Attachment ◽  
Three Dimensional ◽  
Bone Defects ◽  
Metal Alloys ◽  
Potential Candidate ◽  
Natural Bone

Recently, cases of bone defects have been increasing incrementally. Thus, repair or replacement of bone defects is gradually becoming a huge problem for orthopaedic surgeons. Three-dimensional (3D) scaffolds have since emerged as a potential candidate for bone replacement, of which titanium (Ti) alloys are one of the most promising candidates among the metal alloys due to their low cytotoxicity and mechanical properties. However, bioactivity remains a problem for metal alloys, which can be enhanced using simple immersion techniques to coat bioactive compounds onto the surface of Ti–6Al–4V scaffolds. In our study, we fabricated magnesium-calcium silicate (Mg–CS) and chitosan (CH) compounds onto Ti–6Al–4V scaffolds. Characterization of these surface-modified scaffolds involved an assessment of physicochemical properties as well as mechanical testing. Adhesion, proliferation, and growth of human Wharton’s Jelly mesenchymal stem cells (WJMSCs) were assessed in vitro. In addition, the cell attachment morphology was examined using scanning electron microscopy to assess adhesion qualities. Osteogenic and mineralization assays were conducted to assess osteogenic expression. In conclusion, the Mg–CS/CH coated Ti–6Al–4V scaffolds were able to exhibit and retain pore sizes and their original morphologies and architectures, which significantly affected subsequent hard tissue regeneration. In addition, the surface was shown to be hydrophilic after modification and showed mechanical strength comparable to natural bone. Not only were our modified scaffolds able to match the mechanical properties of natural bone, it was also found that such modifications enhanced cellular behavior such as adhesion, proliferation, and differentiation, which led to enhanced osteogenesis and mineralization downstream. In vivo results indicated that Mg–CS/CH coated Ti–6Al–4V enhances the bone regeneration and ingrowth at the critical size bone defects of rabbits. These results indicated that the proposed Mg–CS/CH coated Ti–6Al–4V scaffolds exhibited a favorable, inducive micro-environment that could serve as a promising modification for future bone tissue engineering scaffolds.

Requirements for the Manufacturing of Scaffold Biomaterial With Features at Multiple Scales

2005 ◽  
Author(s):  
I. M. Sebastine ◽  
D. J. Williams
Keyword(s):  
Tissue Engineering ◽  
Multiple Scales ◽  
Cell Attachment ◽  
Structural Parameters ◽  
Complex Function ◽  
Three Dimensional ◽  
Cell Orientation ◽  
Length Scales

Tissue engineering aims to restore the complex function of diseased tissue using cells and scaffold materials. Tissue engineering scaffolds are three-dimensional (3D) structures that assist in the tissue engineering process by providing a site for cells to attach, proliferate, differentiate and secrete an extra-cellular matrix, eventually leading cells to form a neo-tissue of predetermined, three-dimensional shape and size. For a scaffold to function effectively, it must possess the optimum structural parameters conducive to the cellular activities that lead to tissue formation; these include cell penetration and migration into the scaffold, cell attachment onto the scaffold substrate, cell spreading and proliferation and cell orientation. In vivo, cells are organized in functional tissue units that repeat on the order of 100 μm. Fine scaffold features have been shown to provide control over attachment, migration and differentiation of cells. In order to design such 3D featured constructs effectively understanding the biological response of cells across length scales from nanometer to millimeter range is crucial. Scaffold biomaterials may need to be tailored at three different length scales: nanostructure (<1μm), microstructure (<20–100μm), and macrostructure (>100μm) to produce biocompatible and biofunctional scaffolds that closely resemble the extracellular matrix (ECM) of the natural tissue environment and promote cell adhesion, attachment, spreading, orientation, rate of movement, and activation. Identification of suitable fabrication techniques for manufacturing scaffolds with the required features at multiple scales is a significant challenge. This review highlights the effect and importance of the features of scaffolds that can influence the behaviour of cells/tissue at different length scales in vitro to increase our understanding of the requirements for the manufacture of functional 3D tissue constructs.

Bioresorbable Mg-Based Metastable Nano-Alloys for Orthopedic Fixation Devices

2020 ◽  
Vol 20 (3) ◽  
pp. 1504-1510
Author(s):  
Lamei Yan ◽  
Meiling Zhang ◽  
Mihang Wang ◽  
Yuhui Guo ◽  
Xiangquan Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Post Treatment ◽  
Potential Candidate ◽  
Clear Indication ◽  
Laser Melting ◽  
Orthopedic Fixation Devices ◽  
Fixation Devices ◽  
Mechanical Properties And Corrosion

This research has been accomplished using the advanced selective laser melting (SLM) technique as well as HIP post-treatment in order to improve mechanical properties and biocompatibility of Mg– Ca–Sr alloy. Through this research it becomes clearly noticeable that the Mg–1.5Ca–xSr (x = 0.6, 2.1, 2.5) alloys with Sr exhibited better mechanical properties and corrosion potentials. This is more particular with the Mg–1.5Ca–2.5Sr alloy after HIP post-treatment allowing it to provide a desired combination of degradation and mechanical behavior for orthopedic fracture fixation during a desired treatment period. In vivo trials, there was a clear indication and exhibition that this Mg–1.5Ca–2.5Sr alloy screw can completely dissolve in miniature pig’s body which leads to an acceleration in growth of bone tissues. Mg–Ca–Sr alloy proved potential candidate for use in orthopedic fixation devices through Our results concluded that Mg–Ca–Sr alloy are potential candidate for use in orthopedic fixation devices through mechanical strength and biocompatibility evaluations (in vitro or In vivo).

scholarly journals Nanoporous Calcium Silicate and PLGA Biocomposite for Bone Repair

2010 ◽  
Vol 2010 ◽  
pp. 1-9
Author(s):  
Jiacan Su ◽  
Zhiwei Wang ◽  
Yonggang Yan ◽  
Yongfa Wu ◽  
Liehu Cao ◽  
...  
Keyword(s):  
Polyethylene Oxide ◽  
Calcium Silicate ◽  
Bone Repair ◽  
Cell Attachment ◽  
High Surface ◽  
High Surface Area ◽  
Poly Lactic Acid ◽  
Ammonium Bromide

Nanoporous calcium silicate (n-CS) with high surface area was synthesized using the mixed surfactants of EO20PO70EO20(polyethylene oxide)20(polypropylene oxide)70(polyethylene oxide)20, P123) and hexadecyltrimethyl ammonium bromide (CTAB) as templates, and its composite with poly(lactic acid-co-glycolic acid) (PLGA) were fabricated. The results showed that the n-CS/PLGA composite (n-CPC) with 20 wt% n-CS could induce a dense and continuous layer of apatite on its surface after soaking in simulated body fluid (SBF) for 1 week, suggesting the excellent in vitro bioactivity. The n-CPC could promote cell attachment on its surfaces. In addition, the proliferation ratio of MG63cells on n-CPC was significantly higher than PLGA; the results demonstrated that n-CPC had excellent cytocompatibility. We prepared n-CPC scaffolds that contained open and interconnected macropores ranging in size from 200 to 500 μm. The n-CPC scaffolds were implanted in femur bone defect of rabbits, and thein vivobiocompatibility and osteogenicity of the scaffolds were investigated. The results indicated that n-CPC scaffolds exhibited good biocompatibility, degradability, and osteogenesis in vivo. Collectively, these results suggested that the incorporation of n-CS in PLGA produced biocomposites with improved bioactivity and biocompatibility.

scholarly journals Functional regeneration of tendons using scaffolds with physical anisotropy engineered via microarchitectural manipulation

2018 ◽  
Vol 4 (10) ◽  
pp. eaat4537 ◽  
Author(s):  
Z. Wang ◽  
W. J. Lee ◽  
B. T. H. Koh ◽  
M. Hong ◽  
W. Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Type I Collagen ◽  
Three Dimensional ◽  
Type I ◽  
High Porosity ◽  
Cytoskeletal Network ◽  
Function Relationship ◽  
Living Tissues

Structural and hierarchical anisotropy underlies the structure-function relationship of most living tissues. Attempts to exploit the interplay between cells and their immediate environment have rarely featured macroscale, three-dimensional constructs required for clinical applications. Furthermore, compromises to biomechanical robustness during fabrication often limit the scaffold’s relevance in translational medicine. We report a polymeric three-dimensional scaffold with tendon-like mechanical properties and controlled anisotropic microstructures. The scaffold was composed of two distinct portions, which enabled high porosity while retaining tendon-like mechanical properties. When tenocytes were cultured in vitro on the scaffold, phenotypic markers of tenogenesis such as type-I collagen, decorin, and tenascin were significantly expressed over nonanisotropic controls. Moreover, highly aligned intracellular cytoskeletal network and high nuclear alignment efficiencies were observed, suggesting that microstructural anisotropy might play the epigenetic role of mechanotransduction. When implanted in an in vivo micropig model, a neotissue that formed over the scaffold resembled native tendon tissue in composition and structure.

Remote Determination of Time-Dependent Stiffness of Surface-Degrading-Polymer Scaffolds Via Synchrotron-Based Imaging

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
N. K. Bawolin ◽  
X. B. Chen
Keyword(s):  
Mechanical Properties ◽  
Three Dimensional ◽  
Tissue Scaffolds ◽  
Time Dependent ◽  
Element Analysis ◽  
Surface Degradation ◽  
Direct Measurements ◽  
Nonlinear Stress

Surface-degrading polymers have been widely used to fabricate scaffolds with the mechanical properties appropriate for tissue regeneration/repair. During their surface degradation, the material properties of polymers remain approximately unchanged, but the scaffold geometry and thus mechanical properties vary with time. This paper presents a novel method to determine the time-dependent mechanical properties, particularly stiffness, of scaffolds from the geometric changes captured by synchrotron-based imaging, with the help of finite element analysis (FEA). Three-dimensional (3D) tissue scaffolds were fabricated from surface-degrading polymers, and during their degradation, the tissue scaffolds were imaged via the synchrotron-based imaging to characterize their changing geometry. On this basis, the stiffness behavior of scaffolds was estimated from the FEA, and the results obtained were compared to the direct measurements of scaffold stiffness from the load–displacement material testing. The comparison illustrates that the Young's moduli estimated from the FEA and characterized geometry are in agreement with the ones of direct measurements. The developed method of estimating the mechanical behavior was also demonstrated effective with a nondegrading scaffold that displays the nonlinear stress–strain behavior. The in vivo monitoring of Young's modulus by morphology characterization also suggests the feasibility of characterizing experimentally the difference between in vivo and in vitro surface degradation of tissue engineering constructs.

In vitro and in vivo polysaccharides assembly: ultrastructural and cytochemical study of growing plant cell wall components.

1978 ◽  
Vol 36 (2) ◽  
pp. 434-435
Author(s):  
D. Reis ◽  
B. Vian ◽  
J. C. Roland
Keyword(s):  
Cell Wall ◽  
Self Assembly ◽  
Plant Cell Wall ◽  
Higher Plants ◽  
Three Dimensional ◽  
Cytochemical Study ◽  
Wall Components

Wall morphogenesis in higher plants is a problem still open to controversy. Until now the possibility of a transmembrane control and the involvement of microtubules were mostly envisaged. Self-assembly processes have been observed in the case of walls of Chlamydomonas and bacteria. Spontaneous gelling interactions between xanthan and galactomannan from Ceratonia have been analyzed very recently. The present work provides indications that some processes of spontaneous aggregation could occur in higher plants during the formation and expansion of cell wall.Observations were performed on hypocotyl of mung bean (Phaseolus aureus) for which growth characteristics and wall composition have been previously defined.In situ, the walls of actively growing cells (primary walls) show an ordered three-dimensional organization (fig. 1). The wall is typically polylamellate with multifibrillar layers alternately transverse and longitudinal. Between these layers intermediate strata exist in which the orientation of microfibrils progressively rotates. Thus a progressive change in the morphogenetic activity occurs.

Epithelial Organotypic Cultures: A Viable Model to Address Mechanisms of Carcinogenesis by Epitheliotropic Viruses

2018 ◽  
Vol 18 (4) ◽  
pp. 246-255 ◽  
Author(s):  
Lara Termini ◽  
Enrique Boccardo
Keyword(s):  
Three Dimensional ◽  
Cell Types ◽  
Experimental Models ◽  
Biological Research ◽  
Specific Gene ◽  
Specific Cell ◽  
Organotypic Cultures ◽  
Skin Physiology

In vitro culture of primary or established cell lines is one of the leading techniques in many areas of basic biological research. The use of pure or highly enriched cultures of specific cell types obtained from different tissues and genetics backgrounds has greatly contributed to our current understanding of normal and pathological cellular processes. Cells in culture are easily propagated generating an almost endless source of material for experimentation. Besides, they can be manipulated to achieve gene silencing, gene overexpression and genome editing turning possible the dissection of specific gene functions and signaling pathways. However, monolayer and suspension cultures of cells do not reproduce the cell type diversity, cell-cell contacts, cell-matrix interactions and differentiation pathways typical of the three-dimensional environment of tissues and organs from where they were originated. Therefore, different experimental animal models have been developed and applied to address these and other complex issues in vivo. However, these systems are costly and time consuming. Most importantly the use of animals in scientific research poses moral and ethical concerns facing a steadily increasing opposition from different sectors of the society. Therefore, there is an urgent need for the development of alternative in vitro experimental models that accurately reproduce the events observed in vivo to reduce the use of animals. Organotypic cultures combine the flexibility of traditional culture systems with the possibility of culturing different cell types in a 3D environment that reproduces both the structure and the physiology of the parental organ. Here we present a summarized description of the use of epithelial organotypic for the study of skin physiology, human papillomavirus biology and associated tumorigenesis.

scholarly journals The Revolutionary Roads to Study Cell–Cell Interactions in 3D In Vitro Pancreatic Cancer Models

Cancers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 930
Author(s):  
Donatella Delle Cave ◽  
Riccardo Rizzo ◽  
Bruno Sainz ◽  
Giuseppe Gigli ◽  
Loretta L. del Mercato ◽  
...  
Keyword(s):  
Pancreatic Cancer ◽  
Therapeutic Response ◽  
Three Dimensional ◽  
Cellular Models ◽  
Common Cancer ◽  
Cancer Models ◽  
Anti Cancer ◽  
Tumor Environment

Pancreatic cancer, the fourth most common cancer worldwide, shows a highly unsuccessful therapeutic response. In the last 10 years, neither important advancements nor new therapeutic strategies have significantly impacted patient survival, highlighting the need to pursue new avenues for drug development discovery and design. Advanced cellular models, resembling as much as possible the original in vivo tumor environment, may be more successful in predicting the efficacy of future anti-cancer candidates in clinical trials. In this review, we discuss novel bioengineered platforms for anticancer drug discovery in pancreatic cancer, from traditional two-dimensional models to innovative three-dimensional ones.

Three-dimensional Growth of Renal Epithelial Cells in Vitro: A Tool in Toxicity Testing

1993 ◽  
Vol 21 (2) ◽  
pp. 191-195 ◽  
Author(s):  
Knut-Jan Andersen ◽  
Erik Ilsø Christensen ◽  
Hogne Vik
Keyword(s):  
Epithelial Cells ◽  
Three Dimensional ◽  
Toxicity Testing ◽  
Renal Tissue ◽  
Epithelial Cell Line ◽  
Multicellular Spheroids ◽  
Renal Epithelial Cell ◽  
Renal Epithelial Cells

The tissue culture of multicellular spheroids from the renal epithelial cell line LLC-PK1 (proximal tubule) is described. This represents a biological system of intermediate complexity between renal tissue in vivo and simple monolayer cultures. The multicellular structures, which show many similarities to kidney tubules in vivo, including a vectorial water transport, should prove useful for studying the potential nephrotoxicity of drugs and chemicals in vitro. In addition, the propagation of renal epithelial cells as multicellular spheroids in serum-free culture may provide information on the release of specific biological parameters, which may be suppressed or masked in serum-supplemented media.

Sign in / Sign up

Export Citation Format

Share Document