scholarly journals Mechanical Behavior of Fine Recycled Concrete Aggregate Concrete with the Mineral Admixtures

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2264
Author(s):  
Minkwan Ju ◽  
Jae-Gwon Jeong ◽  
Martin Palou ◽  
Kyoungsoo Park
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Performance ◽  
Total Porosity ◽  
Recycled Concrete ◽  
Mineral Admixtures ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
The Relationship ◽  
Normal Dosage

The paper describes the mechanical behavior of fine recycled concrete aggregate (FRCA) concrete according to the mineral admixtures. Three types of the mineral admixtures, i.e., fly ash (FA), ground-granulated blast-furnace slag (GGBS), and silica fume (SF), are used and the replacement ratios of FRCA are 50% and 100%. The dosages of the admixtures of FA, GGBS, and SF are determined with the normal dosage (30%, 40%, and 5.0%, respectively) based on the ACI committee reports (No. 232, 233, and 234) and half-normal dosage. The mechanical performance is investigated with the compressive and splitting tensile strength, and elastic modulus. Additionally, the total porosity is measured in natural fine aggregate (NFA) and FRCA 100% replaced specimens by mercury intrusion porosimetry (MIP) for investigating the relationship with the compressive strength. Based on the experimental test results, the mineral admixtures improve the mechanical performance of FRCA concrete. The effective dosages of FA, GGBS, and SF for FRCA concrete are investigated according to the replacement ratio of the FRCA. In particular, FRCA 100% replaced concrete may be possible to be used for the structural concrete members with the specific dosage of the mineral admixtures. The prediction of the splitting tensile strength and the elastic modulus by the codes or previous formulas exhibits underestimated and overestimated results, respectively. The relationship between the total porosity and the compressive strength of the FRCA concrete should be modified with more experimental tests.

scholarly journals Mechanical Performance of Recycled Aggregate Concrete Containing Lathe Waste Steel Fibre

2021 ◽  
Vol 17 (4) ◽  
pp. 306-311
Author(s):  
S.A. Alabi ◽  
C. Arum
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Building Materials ◽  
Steel Fibre ◽  
Mechanical Performance ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Aggregate Concrete

The increasing demand, diminishing supplies, and growing pressure on natural resources have necessitated recycling and reusing waste. Several kinds of research have been done on the reuse and recycling of debris from building projects. Thus, with a view to the reuse of waste materials, the elimination of environmental contamination, the reduction of overhead costs of concrete, and the extension of the service life of concrete structures, this research aimed to study the feasibility of utilizing recycled concrete aggregate (RCA) with constant inclusion of waste steel fibre (LWSF) in concrete by evaluating its workability, compressive and splitting tensile strengths. A concrete mix ratio of 1:2:4 by weight of cement, sand, and granite was adopted with a water-cement ratio of 0.45. Five different concrete mixes were prepared in this study; one normal aggregate concrete (NAC) and four (4) other mixes with 25%, 50%, 75%, and 100% recycled aggregate content with a constant 1.5% addition of LWSF. The result of workability shows a reduction with an increase in the percentage replacement level. The recycled aggregate concrete (RAC) was characterized by lower compressive strength as compared with the NAC. When the replacement ratio increased from 25% to 50%, a significant reduction of about 14% and 30% were observed in the compressive strength at 7-days, but at 28-days slight increase in the compressive strength was observed. Also, a decrease in splitting tensile strength as the percentage replacement of crushed granite (CG) with RCA is increased was observed. Overall, the findings showed that the RAC-containing LWSF is environmentally sustainable and would significantly reduce the global greenhouse impact and building materials' overall quality. Keywords: Recycled concrete, lathe waste, steel fibre, compressive strength, tensile strength

EFFECT OF RECYCLED CONCRETE AGGREGATE QUALITY ON PROPERTIES OF CONCRETE

2020 ◽  
Vol 15 (2) ◽  
pp. 57-69
Author(s):  
Daniel Hatungimana ◽  
Şemsi Yazıcı ◽  
Ali Mardani-Aghabaglou
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Hardened Concrete ◽  
Recycled Concrete Aggregate ◽  
Waste Concrete ◽  
Concrete Production

ABSTRACT The possibility of the use of recycled aggregates from the construction industry in green concrete production is of increasing importance to reduce the negative environmental impact associated with construction and demolition wastes. The objective of this study is to investigate the effect of recycled concrete aggregate (RCA) quality on the properties of hardened concrete properties such as compressive strength, splitting tensile strength, density, water absorption capacity and porosity accessible to water. The RCA used in this study was obtained from the crushing of waste concrete with two different compressive strengths (LRCA obtained from the crushing of waste concrete having compressive strengths below 30 MPa and HRCA obtained from the crushing of waste concrete having compressive strengths above 30 MPa). The natural coarse limestone aggregate was 100% replaced with coarse LRCA and HRCA. As a result of the study, the use of 100% HRCA and %100 LRCA instead of limestone coarse aggregate in the concrete adversely affected its mechanical and physical properties. In addition, HRCA showed better performance in terms of compressive strength, tensile strength, water absorption and porosity compared to the use of LRCA. Furthermore, the percentage of adhered mortar on the surface of LRCA and HRCA was analyzed using a computerized micro tomography device, and it was found that the percentages of attached mortar and aggregates are 61% and 35.5% for LRCA, whilst the attached mortar and aggregate contents for HRCA are 45.9% and 53.7%, respectively.

scholarly journals Roller Compacted Concrete with Recycled Concrete Aggregate for Paving Bases

2020 ◽  
Vol 12 (8) ◽  
pp. 3154 ◽  
Author(s):  
Hedelvan Emerson Fardin ◽  
Adriana Goulart dos Santos
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Roller Compacted Concrete ◽  
Flexural Tensile Strength ◽  
Mechanical And Physical Properties

This research aimed to investigate the mechanical and physical properties of Roller Compacted Concrete (RCC) used with Recycled Concrete Aggregate (RCA) as a replacement for natural coarse aggregate. The maximum dry density method was adopted to prepare RCC mixtures with 200 kg/m³ of cement content and coarse natural aggregates in the concrete mixture. Four RCC mixtures were produced from different RCA incorporation ratios (0%, 5%, 15%, and 30%). The compaction test, compressive strength, splitting tensile strength, flexural tensile strength, and modulus of elasticity, porosity, density, and water absorption tests were performed to analyze the mechanical and physical properties of the mixtures. One-way Analysis of Variance (ANOVA) was used to identify the influences of RCA on RCC’s mechanical properties. As RCA increased in mixtures, some mechanical properties were observed to decrease, such as modulus of elasticity, but the same was not observed in the splitting tensile strength. All RCCs displayed compressive strength greater than 15.0 MPa at 28 days, splitting tensile strength above 1.9 MPa, flexural tensile strength above 2.9 MPa, and modulus of elasticity above 19.0 GPa. According to Brazilian standards, the RCA added to RCC could be used for base layers.

scholarly journals Effect of River Indus Sand and Recycled Concrete Aggregates as Fine and Coarse Replacement on Properties of Concrete

2019 ◽  
Vol 9 (1) ◽  
pp. 3832-3835 ◽  
Author(s):  
A. R. Sandhu ◽  
M. T. Lakhiar ◽  
A. A. Jhatial ◽  
H. Karira ◽  
Q. B. Jamali
Keyword(s):  
Tensile Strength ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Concrete Aggregates ◽  
Recycled Concrete Aggregates ◽  
Compressive Strength Of Concrete ◽  
River Indus ◽  
Concrete Materials

As the demand for concrete rises, the concrete materials demand increases. Aggregates occupy 75% of concrete. A vast amount of aggregates is utilized in concrete while aggregate natural resources are reducing. To overcome this problem, River Indus sand (RIS) and recycled concrete aggregate (RCA) were utilized as fine and coarse aggregate respectively. The aim of this experimental investigation is to evaluate the workability, and compressive and tensile strength of concrete utilizing RIS and RCA. Concrete samples of 1:2:4 proportions were cast, water cured for 7, 14, 21 and 28 days, and tested for compressive and tensile strength. The outcomes demonstrate that concrete possessed less workability when RIS and RCA were utilized. It was predicted that compressive strength of concrete would reduce up to 1.5% when 50% RIS and 50% RCA were utilized in concrete and 11.5% when natural aggregate was fully replaced by RIS and RCA, whereas the tensile strength decreased up to 1.60% when 50% by 12% respectively.

scholarly journals Evaluation of the Feasibility of Recycled Concrete Aggregate for Producing Structural Concrete

2020 ◽  
Vol 220 ◽  
pp. 01098
Author(s):  
Mohammad Tabrez Ali ◽  
Ibadur Rahman ◽  
Nirendra Dev ◽  
Priyanka Singh
Keyword(s):  
Compressive Strength ◽  
Construction Materials ◽  
Recycled Concrete ◽  
Environmental Benefits ◽  
Mix Design ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Structural Concrete ◽  
Average Value ◽  
Maximum Compressive Strength

When sustainability has become a primary measure of the selection of the building materials in the construction industry over the past decades, researchers all around the world have been looking upon for alternatives to reduce the overall environmental impact of the construction materials while not compromising the strength and durability. The factors like manufacturing, reusability, recyclability, disposal etc, are the criteria of utmost attention affecting the overall life cycle impact of the construction materials. In this prospect the Recycled Concrete Aggregate (RCA) has shown up as an exceptionally viable contender for the manufacturing of concrete with several environmental benefits over the Natural Aggregate (NA) and has already been identified by industry and several government agencies across the globe. The efficient material use of RCA can potentially deliver an inferior though competent concrete in comparison to the NA while averring the criteria of sustenance. The present study delves into the calculation of the proportion of the RCA in a mix design for achieving maximum compressive strength. The experimental setup constituted the casting of concrete cubes of control mix design of M40 grade with proportions of RCA varying from 0-100 percent spread over a space of 10% with NA which were later put to tests. The thorough investigation on the casted concrete cubes lead to the conclusion that the mix design with 50% proportion of RCA in addition to 50% proportion of NA delivered the maximum compressive strength, an average value of 8.23% higher than that of the normal concrete and the highest Rebound Number, an average value of 53.92 for the M40 grade concrete thereby showcasing the feasibility of producing structural concrete with RCA. The results are asserted to be governed by the better bonding between the RCA and NA and due to the significant increase in the water retention capacity by the provision of RCA in the mix.

scholarly journals Concrete with Partial Substitution of Waste Glass and Recycled Concrete Aggregate

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 430
Author(s):  
Jawad Ahmad ◽  
Rebeca Martínez-García ◽  
Jesús de-Prado-Gil ◽  
Kashif Irshad ◽  
Mohammed A. El-Shorbagy ◽  
...  
Keyword(s):  
Performance Test ◽  
Coarse Aggregate ◽  
Mechanical Performance ◽  
Negative Impact ◽  
Strength Properties ◽  
Waste Glass ◽  
Recycled Concrete ◽  
Partial Substitution ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate

The current practice of concrete is thought to be unsuitable because it consumes large amounts of cement, sand, and aggregate, which causes depletion of natural resources. In this study, a step towards sustainable concrete was made by utilizing recycled concrete aggregate (RCA) as a coarse aggregate. However, researchers show that RCA causes a decrease in the performance of concrete due to porous nature. In this study, waste glass (WG) was used as a filler material that filled the voids between RCA to offset its negative impact on concrete performance. The substitution ratio of WG was 10, 20, or 30% by weight of cement, and RCA was 20, 40, and 60% by weight of coarse aggregate. The slump cone test was used to assess the fresh property, while compressive, split tensile, and punching strength were used to assess the mechanical performance. Test results indicated that the workability of concrete decreased with substitution of WG and RCA while mechanical performance improved up to a certain limit and then decreased due to lack of workability. Furthermore, a statical tool response surface methodology was used to predict various strength properties and optimization of RCA and WG.

Properties of Dry-Mortar with Recycled Concrete Aggregate and Powder of Crushed Clay Bricks

2011 ◽  
Vol 374-377 ◽  
pp. 1637-1640
Author(s):  
Jian Hua Xue ◽  
Xiao Guang Li ◽  
Yun Xiao Liu ◽  
Qiang Du
Keyword(s):  
Compressive Strength ◽  
Physical And Mechanical Properties ◽  
Recycled Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Mass Ratio ◽  
Clay Brick ◽  
Natural Sand ◽  
Clay Bricks

Recycled concrete aggregate (RCA) and crushed clay bricks (CCB) have been increasingly researched and used in past two decades. However, studies focusing on the properties of dry-mortar with RCA and CCB are very limited. In this research, results from physical and mechanical properties of recycled mortar with fine recycled aggregate (FRA), fine recycled powder (FRP) and crushed clay brick (CCB) were secured. It is shown that sinking degree of FRA mortar can be adjusted in the range of 70-90mm and their water-maintainability is superior to natural sand mortar. However, compressive strength of FRA mortar at various ages decrease, compared to natural sand mortar under the condition of same mixed proportion. Compressive strength of FRA mortar is above 5.0MPa with mass ratio of aggregate to cement lower than 6.0.Workability of FRP and CCB mortar is similar to fly ash mortar and their apparent densities are under the 2.0g/cm3. Compressive strength of FRP and CCB mortar is near to 8.5 MPa at 28 days of age.

Relationship between the Compressive and Tensile Strength of Recycled Concrete

2011 ◽  
Vol 324 ◽  
pp. 348-351 ◽  
Author(s):  
Rouba El Dalati ◽  
Pierre Matar ◽  
Sara Haddad ◽  
Fadi Hage Chehade
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Limited Range ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Concrete Compressive Strength ◽  
Concrete Recycling ◽  
The Relationship ◽  
Special Composition

Concrete recycling consists of crushing the concrete provided by demolishing the old constructions, and of using the resulted small pieces as aggregates in the new concrete compositions. The resulted aggregates are called recycled aggregates and the new mix of concrete containing a percentage of recycled aggregates is called recycled concrete. Our previous researches have indicated the optimal percentages of recycled aggregates to be used for different cases of recycled concrete related to the original aggregates nature. All results have shown that the concrete compressive strength is significantly reduced when using recycled aggregates. In order to obtain realistic values of compressive strength, some tests have been carried out by adding water-reducer plasticizer and a specified additional quantity of cement. The results have shown that for a limited range of plasticizer percentage, and a fixed value of additional cement, the compressive strength has reached reasonable value. This paper treats of the effect of using recycled aggregates on the tensile strength of concrete, where concrete results from the special composition defined by our previous work. The aim is to determine the relationship between the compressive and tensile strength of recycled concrete.

Research on Mechanical Properties of Steel Fiber Reinforced High Performance Recycled Concrete

2010 ◽  
Vol 168-170 ◽  
pp. 2044-2048
Author(s):  
Wen Li Li ◽  
Wen Ge Chai ◽  
Cheng Yi ◽  
Yan Li Gao ◽  
Zhao Guang Li
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Performance ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Mineral Admixtures ◽  
Energy Increase ◽  
Bending Load ◽  
Different Content

In this paper, high-quality mineral admixtures and superplasticizer double mixing technology is used to produce high performance recycled concert (HPRC), and then steel fibers are used to modify the characteristics of HPRAC. The compressive strength, splitting tensile strength, ultimate bending load and fracture energy of HPRC with different content of steel fiber. Experiments suggest that with the increase of steel fiber content, the compressive strength doesn’t change too much, but the splitting tensile strength, ultimate bending load and facture energy increase dramatically. Therefore it can be concluded that increasing the content of steel fiber properly can improve the ductility and resistance to crack propagation of HPRC and enhance the ultimate load of HPRC bending member.

Sign in / Sign up

Export Citation Format

Share Document