scholarly journals Effect of Isothermal Transformation Times below Ms and Tempering on Strength and Toughness of Low-Temperature Bainite in 0.53 C Bainitic Steel

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2418
Author(s):  
Enzuo Liu ◽  
Qiangguo Li ◽  
Sufyan Naseem ◽  
Xuefei Huang ◽  
Weigang Huang
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Isothermal Transformation ◽  
Electron Back Scatter Diffraction ◽  
Bainitic Steel ◽  
Transmission Electron ◽  
The Impact ◽  
Tempering Process

This study aims to investigate the microstructures, strength, and impact toughness of low-temperature bainite obtained by isothermal transformation at temperature below Ms (Martensite Starting temperature) for different times and tempering process in 0.53 C wt% bainitic steel. By using the optical microscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), electron back scatter diffraction (EBSD), and mechanical property test, it was found that the microstructures after heat treatment consist of small amounts of martensite, fine bainite, and film retained austenite. After tempered at 250 °C for 2 h, the volume fraction of retained austenite (10.9%) in the sample treated by isothermal transformation at 220 °C for three hours is almost the same as that of the sample without tempering. In addition, the retained austenite fraction decreases with the increase of holding times and is reduced to 6.8% after holding for 15 h. The ultimate tensile strength (1827 MPa), yield strength (1496 MPa), total elongations (16.1%), and impact toughness (up to 58 J/cm2) were obtained by isothermal transformation at 220 °C for three hours and tempered at 250 °C. Whereas, the impact toughness of sample without tempering is 28 J/cm2. After holding for 15 h, the impact toughness raises to 56 J/cm2, while the ductility and strength decreases. These results indicate that the tempering process is helpful to improve the impact toughness of low-temperature bainite.

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

2018 ◽  
Vol 941 ◽  
pp. 329-333 ◽  
Author(s):  
Jiang Ying Meng ◽  
Lei Jie Zhao ◽  
Fan Huang ◽  
Fu Cheng Zhang ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Isothermal Treatment ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Microstructure And Mechanical Properties

In the present study, the effects of ausforming on the bainitic transformation, microstructure and mechanical properties of a low-carbon rich-silicon carbide-free bainitic steel have been investigated. Results show that prior ausforming shortens both the incubation period and finishing time of bainitic transformation during isothermal treatment at a temperature slightly above the Mspoint. The thicknesses of bainitic ferrite laths are reduced appreciably by ausforming; however, ausforming increases the amount of large blocks of retained austenite/martenisite and decreases the volume fraction of retained austenite. And accordingly, ausforming gives rise to significant increases in both yield and tensile strengths, but causes noticeable decreases in ductility and impact toughness.

scholarly journals The Effect of Tempering on the Microstructure and Mechanical Properties of a Novel 0.4C Press-Hardening Steel

2019 ◽  
Vol 9 (20) ◽  
pp. 4231
Author(s):  
Oskari Haiko ◽  
Antti Kaijalainen ◽  
Sakari Pallaspuro ◽  
Jaakko Hannula ◽  
David Porter ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Temperature ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Hot Strip Mill ◽  
Tempering Temperature ◽  
Press Hardening ◽  
Dislocation Densities ◽  
The Impact

In this paper, the effects of different tempering temperatures on a recently developed ultrahigh-strength steel with 0.4 wt.% carbon content were studied. The steel is designed to be used in press-hardening for different wear applications, which require high surface hardness (650 HV/58 HRC). Hot-rolled steel sheet from a hot strip mill was austenitized, water quenched and subjected to 2-h tempering at different temperatures ranging from 150 °C to 400 °C. Mechanical properties, microstructure, dislocation densities, and fracture surfaces of the steels were characterized. Tensile strength greater than 2200 MPa and hardness above 650 HV/58 HRC were measured for the as-quenched variant. Tempering decreased the tensile strength and hardness, but yield strength increased with low-temperature tempering (150 °C and 200 °C). Charpy-V impact toughness improved with low-temperature tempering, but tempered martensite embrittlement at 300 °C and 400 °C decreased the impact toughness at −40 °C. Dislocation densities as estimated using X-ray diffraction showed a linear decrease with increasing tempering temperature. Retained austenite was present in the water quenched and low-temperature tempered samples, but no retained austenite was found in samples subjected to tempering at 300 °C or higher. The substantial changes in the microstructure of the steels caused by the tempering are discussed.

Retained Austenite Control and Extra-Cryogenic Impact Toughness of Fe-3.0%Mn Low Carbon Steel

2020 ◽  
Vol 993 ◽  
pp. 520-525
Author(s):  
Xiang Tao Deng ◽  
Xiao Lin Li ◽  
Long Huang ◽  
Zhao Dong Wang
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Low Temperature ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Uniform Elongation ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Low Temperature Impact Toughness ◽  
The Impact

The control of the retained austenite in Fe-3.0%Mn Low carbon steel by a three-step intercritical heat treatment and the low-temperature impact toughness evolution during the process were analyzed in the present study. The results indicated that the microstructure consisted intercritical ferrite, martensite/bainite and retained austenite. The distribution of carbon and manganese could improve the stability of the austenite located at the grain boundaries of prior austenite and lath boundaries of martensite. For the TRIP effect of the austenite, the excellent plasticity and low temperature toughness was obtained. The impact toughness could reach 200 J (impact energy) at －80 °C during the three-step heat treatment, and the uniform elongation could exceed at 16%.

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

Microstructure and Tensile Properties of TRIP-Aided Steel Sheet Subjected to Hot-Rolling and Austempering

2021 ◽  
Vol 1016 ◽  
pp. 732-737
Author(s):  
Junya Kobayashi ◽  
Hiroto Sawayama ◽  
Naoya Kakefuda ◽  
Goroh Itoh ◽  
Shigeru Kuraoto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Hot Rolling ◽  
Manufacturing Process ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Isothermal Holding ◽  
High Strength ◽  
Isothermal Transformation ◽  
Transformation Process ◽  
Steel Sheets

Various high strength steel sheets for weight reduction and safety improvement of vehicles have been developed. TRIP-aided steel with transformation induced plasticity of the retained austenite has high strength and ductility. Conventional TRIP-aided steels are subjected to austempering process after austenitizing. Generally, elongation and formability of TRIP-aided steel are improved by finely dispersed retained austenite in BCC phase matrix. The finely dispersed retained austenite and grain refinement of TRIP-aided steel can be achieved by hot rolling with heat treatment. Therefore, the improvement of mechanical properties of TRIP-aided steel is expected from the manufacturing process with hot rolling and then isothermal transformation process. In this study, thermomechanical heat treatment is performed by combining hot rolling and isothermal holding as the manufacturing process of TRIP-aided steel sheets. The complex phase matrix is obtained by hot rolling and then isothermal holding. Although the hardness of the hot rolled and isothermal held TRIP-aided steel is decreased, the volume fraction of retained austenite is increased.

Effect of Ausforming Temperature on Bainite Transformation of High Carbon Low Alloy Steel

2015 ◽  
Vol 817 ◽  
pp. 454-459 ◽  
Author(s):  
Jian Guo He ◽  
Ai Min Zhao ◽  
Huang Yao ◽  
Chao Zhi ◽  
Fu Qing Zhao
Keyword(s):  
Low Temperature ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Transformation Rate ◽  
Low Alloy Steel ◽  
High Carbon ◽  
Bainite Transformation ◽  
Electron Backscattered Diffraction ◽  
In Situ Experiments

The effect of ausforming temperature on bainite transformation of high carbon low alloy steel was studied by in situ experiments using a Gleeble 3500 thermal and mechanical testing system. Morphology and crystallography of ausforming bainite were examined by scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). It has been found that deformation at all temperatures range from 230°C to 600°C can accelerate low temperature bainite transformation, and transformation rate increased with deformation temperature reduced. Quantitative X-ray analysis shows that the volume fraction of retained austenite was about 35.84% after deformation and isothermal transformation for 20 hours, it was approximately the same amount with austempering bainite transformation process (no strain) which austenite volume fraction was about 32.01%. Low temperature bainite formation can be accelerated with a smaller increase amount of retained austenite by deformation at a low temperature range of 230~600 oC.

scholarly journals Microstructure and Mechanical Properties of Tempered Ausrolled Nanobainite Steel

Crystals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 573
Author(s):  
Jing Zhao ◽  
Dezheng Liu ◽  
Yan Li ◽  
Yongsheng Yang ◽  
Tiansheng Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Energy Yield ◽  
Partial Recovery ◽  
Fracture Appearance ◽  
The Impact

The microstructures and mechanical properties of ausrolled nanobainite steel, after being tempered at temperatures in the range of 200−400 °C, were investigated in this study. After being tempered, bainitic ferrite is coarsened and the volume fraction of retained austenite is reduced. The hardness and ultimate tensile strength decrease sharply. The impact energy, yield strength, and elongation increase with elevated tempered temperature at 200–300 °C but decrease with elevated tempered temperature when the samples are tempered at 350 °C and 400 °C. The fracture appearance of all the samples after impact tests is a brittle fracture. The variation of the mechanical properties may be due to partial recovery and recrystallization.

Sign in / Sign up

Export Citation Format

Share Document