scholarly journals A Theoretical Model for Debonding Prediction in the RC Beams Externally Strengthened with Steel Strip and Inorganic Matrix

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4961
Author(s):  
Francesco Bencardino ◽  
Mattia Nisticò
Keyword(s):  
Theoretical Model ◽  
Steel Strip ◽  
Structural Response ◽  
Experimental Tests ◽  
Rc Beams ◽  
Matrix Interface ◽  
Differential Problem ◽  
Bond Slip ◽  
Strain Compatibility ◽  
Lap Shear

This paper shows a theoretical model for predicting the moment–curvature/load–deflection relationships and debonding failure of reinforced concrete (RC) beams externally strengthened with steel reinforced geopolymeric matrix (SRGM) or steel reinforced grout (SRG) systems. Force equilibrium and strain compatibility equations for a beam section divided into several segments are numerically solved using non-linear behaviour of concrete and internal steel bars. The deflection is then obtained from the flexural stiffness at a mid-span section. Considering the appropriate SRGM-concrete bond–slip law, calibrated on single-lap shear bond tests, both end and intermediate debonding failures are analysed. To predict the end debonding, an anchorage strength model is adopted. To predict intermediate debonding, at each pair of flexural cracks a shear stress limitation is placed at concrete–matrix interface and the differential problem is solved at steel strip–matrix interface. Based on the theoretical predictions, the comparisons with experimental data show that the proposed model can accurately predict the structural response of SRGM/SRG strengthened RC beams. It can be a useful tool for evaluating the behaviour of externally strengthened RC beams, avoiding experimental tests.

scholarly journals Bond Behavior of Carbon Fabric-Reinforced Matrix Composites: Geopolymeric Matrix versus Cementitious Mortar

Buildings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 207
Author(s):  
Feras Abu Obaida ◽  
Tamer El-Maaddawy ◽  
Hilal El-Hassan
Keyword(s):  
Shear Stress ◽  
Matrix Model ◽  
Maximum Shear Stress ◽  
Matrix Composites ◽  
Matrix Interface ◽  
Carbon Fabric ◽  
Bond Slip ◽  
Bond Behavior ◽  
Cementitious Matrix ◽  
Lap Shear

This study aims to examine the potential use of a geopolymeric matrix as a sustainable alternative to commercial mortars in carbon fabric-reinforced matrix composites. Single-lap shear tests were conducted to examine the bond behavior at the fabric-matrix interface. Test parameters included the type of matrix (geopolymeric and cementitious matrices) and the bonded length (50 to 300 mm). The geopolymeric matrix was a blend of fly ash/ground granulated blast furnace slag activated by an alkaline solution of sodium silicate and sodium hydroxide. The bond behavior of the geopolymeric-matrix specimens was characterized and compared to that of similar specimens with a cementitious matrix. The specimens failed due to fabric slippage/debonding at the fabric-matrix interface or fabric rupture. The effective bond lengths of the geopolymeric- and cementitious-matrix specimens were 150 and 170 mm, respectively. The geopolymeric-matrix specimens exhibited higher fabric strains, higher ultimate loads, and a steeper strain profile along the bonded length than those of their cementitious-matrix counterparts. New bond-slip models that characterize the bond behavior at the fabric-matrix interface for geopolymeric- and cementitious-matrix specimens were developed. Both models exhibited equal maximum shear stress of 1.2 MPa. The geopolymeric-matrix model had, however, higher fracture energy and higher slip at maximum shear stress than those of the cementitious matrix model.

Analytical Modeling of Composite-to-Masonry Prisms Bond

2014 ◽  
Vol 624 ◽  
pp. 567-574 ◽  
Author(s):  
Marialaura Malena ◽  
Gianmarco de Felice
Keyword(s):  
Experimental Tests ◽  
Displacement Curve ◽  
Experimental Population ◽  
Shear Tests ◽  
Bond Slip ◽  
Clay Bricks ◽  
Lap Shear ◽  
Critical Issues ◽  
Externally Bonded ◽  
Composite Fabrics

The composite-to-substrate interfacial stresses transfer mechanism is one of the critical issues in externally-bonded structural strengthening by means of composite fabrics. In this work, an analytical approach for modeling the debonding process of a composite on a non-homogeneous substrate is developed and applied to simulate the loss of bond of FRP on brick masonry. The analytical formulation is based on the experimental outcomes of bond shear tests, which are part of a Round Robin activity involving several laboratories. The experimental work is the follow up of a previous one [1], and comprises 12 single-lap shear tests of four kinds of unidirectional reinforcement, i.e., glass, carbon, basalt and steel, applied with epoxy resin to masonry prisms composed by five clay bricks and four mortar joints. The analytical simulations of the experimental tests rely upon a bi-linear non-homogeneous bond-slip law that was calibrated using the experimental population. Eventually, the analytical results are compared to experimental ones both, in terms of global (load to displacement curve) and local behavior (strain profile on the reinforcement for increasing load values).

Bond of Steel Bars to Masonry Mortar Joints: Test Results and Analytical Modelling

2017 ◽  
Vol 747 ◽  
pp. 319-325 ◽  
Author(s):  
Matteo Maragna ◽  
Cristina Gentilini ◽  
Giovanni Castellazzi ◽  
Christian Carloni
Keyword(s):  
High Strength ◽  
Experimental Tests ◽  
Analytical Investigation ◽  
Masonry Walls ◽  
Test Results ◽  
Bond Slip ◽  
Pull Out ◽  
Steel Bars ◽  
Masonry Mortar

In this paper, the preliminary results of a series of pull-out tests conducted on mortar cylinders with embedded bars are presented. The bars are made of high strength stainless steel and are of helical shape to increase mechanical interlocking with the surrounding mortar. Usually, such bars are employed in situ to realize structural repointing in the case of fair-faced masonry walls. To this aim, they are inserted in the mortar bed joints of masonry for providing tensile strength to the walls and with the function of crack stitching. The aim of the present experimental tests is to determine the bond-slip relationship for bars embedded in masonry. Firstly, pull-out tests are conducted on mortar cylinders considering different embedded lengths of the bars. Further tests are on-going on masonry specimens with bars embedded in the mortar joints. An analytical investigation is also carried out for the interpretation of the pull-out test results.

Theoretical Model for Interfacial Nonlinear Bond Softening Behavior between Embedded Steel and HSHPC

2007 ◽  
Vol 348-349 ◽  
pp. 845-848
Author(s):  
Shan Suo Zheng ◽  
Lei Li ◽  
Guo Zhuan Deng ◽  
Shun Li Che ◽  
Wei Zhao
Keyword(s):  
Theoretical Model ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Nonlinear Process ◽  
Experimental Results ◽  
Interfacial Bond ◽  
Bond Slip ◽  
Softening Behavior ◽  
Bond Softening

The latest experimental study on steel reinforced high strength and high performance concrete (SRHSHPC) specimens shows that there exists interfacial bond softening phenomenon between embedded steel and high strength and high performance concrete (HSHPC), and it makes the shear transfer capacity between shaped steel and HSHPC be progressively reduced. To predict failure load in design, a theoretical model for interfacial bond softening behavior is required. As interfacial bond softening behavior is a nonlinear process involving material properties, it can be analyzed once the relation of interfacial bond stress (τ ) and slippage ( s ) is known. In this paper, the mechanism of interfacial bond-slip is studied, thus a simplified τ − s relation including ascending and descending parts is proposed and employed to analyze the interfacial nonlinear bond-slip process. Based on the interfacial equilibrium between steel and HSHPC as well as the τ − s relation, the basic governing equations in both softened region and elastic region are established and solved for steel strain or stress. At last, the application of the model is verified through comparison with experimental results. The calculating results of the model are found to be in good agreement with experimental results, showing that the model can describe the bond-slip process in real material systems.

A Theoretical and Experimental Analysis of the Bending Behavior of Unbonded Flexible Pipes

2014 ◽  
Author(s):  
Tatiana Vargas-Londoño ◽  
José Renato M. de Sousa ◽  
Carlos Magluta ◽  
Ney Roitman
Keyword(s):  
Internal Pressure ◽  
Cross Section ◽  
Structural Response ◽  
Experimental Tests ◽  
Theoretical Models ◽  
External Pressure ◽  
Local Behavior ◽  
Flexible Pipes ◽  
Floating System ◽  
Bending Loads

Due to its compound cross-section, the prediction of the structural response of flexible pipes to loads such as their self-weight, internal and external pressure, movements imposed by the floating system and environmental loads such as currents, waves and wind is quite complex. All these loads generate stresses and strains in the cross section of the pipe that have to be properly evaluated in order to ensure integrity of the line. Research has been done on the local behavior of flexible pipes under combined axisymmetric loads as well as under bending loads. However, there is a lack of research combining both axisymmetric and bending loads, as also in the study of the strains in the tensile amour layers of the pipes, aspects which are important for the calibration of theoretical models to predict such behavior. Based on that, this study aims to evaluate the local behavior of flexible pipes under combinations of axisymmetric (tension, and internal pressure) and bending loads via a series of experimental tests in a 9.13″ I.D pipe. In the experimental tests, the behavior of the pipe was studied for three load combinations: i) bending combined with tension; ii) bending combined with internal pressure; and iii) bending combined with tension and internal pressure. Based on these tests, the authors obtained the strains in the tensile armor layer, axial elongation due to tension, axial reaction forces due to internal pressure, and deflection due to bending. These measurements were used to calibrate a theoretical model devoted to simulate the pipe’s response, getting accurate results for stiffness and stresses of the pipe in each scenario.

scholarly journals Effect of Processing Parameters on the Dynamic Characteristic of Material Extrusion Additive Manufacturing Plates

2019 ◽  
Vol 9 (24) ◽  
pp. 5345
Author(s):  
Shijie Jiang ◽  
Yinfang Shi ◽  
Yannick Siyajeu ◽  
Ming Zhan ◽  
Chunyu Zhao ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Theoretical Model ◽  
Dynamic Characteristics ◽  
Dynamic Performance ◽  
Experimental Tests ◽  
Processing Parameters ◽  
Combination Method ◽  
Mode Shapes ◽  
Material Extrusion ◽  
Function Combination

Material extrusion (ME), an additive manufacturing technique, can fabricate parts almost without geometrical limitations. With the growing application of ME parts, especially in actual working conditions, the dynamic characteristics are needed to be studied to accurately determine their reliability. This study provides an experimental validation of the theoretical model for predicting the dynamic characteristics of ME plates fabricated with three different key processing parameters, i.e., extrusion width, layer height and build direction. The model is set up based on the bidirectional beam function combination method, and a series of experimental tests are performed. It is found that different processing parameters result in the material properties of the samples to vary, thus leading to different dynamic characteristics. Through the comparison between predictions and measurements, it is shown that the influencing trend of the processing parameters is predicted precisely. The theoretical model gives reliable predictions in dynamic characteristics of ME plates. The natural frequency discrepancy is below 13.4%, and the predicted mode shapes are the same as the measured ones. This present work provides theoretical basis and technical support for further research in improving the dynamic performance of ME products, and helps extend the applications of this technique.

Bond Behaviour of FRCM Composites: Effects of High Temperature

2019 ◽  
Vol 817 ◽  
pp. 161-166
Author(s):  
Antonio Iorfida ◽  
Sebastiano Candamano ◽  
Fortunato Crea ◽  
Luciano Ombres ◽  
Salvatore Verre ◽  
...  
Keyword(s):  
High Temperature ◽  
Failure Mode ◽  
Failure Modes ◽  
Construction Materials ◽  
Mechanical Damage ◽  
High Density ◽  
Bond Behaviour ◽  
Bond Slip ◽  
Masonry Construction ◽  
Lap Shear

The fire remains one of the serious potential risks to most buildings and structures, as recently it’s been witnessed in Paris’ historic Notre Dame Cathedral and London’s Grenfell Tower. Concrete and masonry construction materials suffer physiochemical changes and mechanical damage caused by heating that is usually confined to the outer surface but can eventually compromise their load-bearing capacity. FRCM systems could provide when applied, supplemental fire insulation on pre-existing structural members, but there is a lack of knowledge about their properties in those conditions. This experimental work, thus, aims to evaluate the mechanical behaviour of carbon-FRCM and basalt-FRCM composites bonded to masonry substrate after high temperature exposure. Temperatures of 100 °C, 300 °C and 500 °C over a period of three hours were used to investigate the degradation of their mechanical properties. Single lap shear bond tests were carried out to evaluate the bond-slip response and failure modes. For all the tested temperatures higher peak stresses were measured for carbon-FRCM composite than basalt ones. Furthermore, low-density basalt-FRCM composite showed higher peak stresses and lower global slips up to 300 °C than high-density one. Carbon-FRCM composite failure mode was not effected by temperature. High-density basalt-FRCM composite showed a change in failure mode between 300 °C and 500 °C.

Sign in / Sign up

Export Citation Format

Share Document