scholarly journals Impact of Induction Furnace Steel Slag as Replacement for Fired Clay Brick Aggregate on Flexural and Durability Performances of RC Beams

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6268
Author(s):  
Md Jihad Miah ◽  
Md. Kawsar Ali ◽  
Ye Li ◽  
Adewumi John Babafemi ◽  
Suvash Chandra Paul
Keyword(s):  
Water Absorption ◽  
Induction Furnace ◽  
Steel Slag ◽  
Chloride Ion ◽  
Rc Beams ◽  
Clay Brick ◽  
Capillary Water ◽  
Capillary Water Absorption ◽  
Chloride Ion Penetration ◽  
Furnace Steel

This research investigates the flexural and durability performances of reinforced concrete (RC) beams made with induction furnace steel slag aggregate (IFSSA) as a replacement for fired clay brick aggregate (FCBA). To achieve this, 27 RC beams (length: 750 mm, width: 125 mm, height: 200 mm) were made with FCBA replaced by IFSSA at nine replacement levels of 0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% (by volume). Flexural tests of RC beams were conducted by a four-point loading test, where the deflection behavior of the beams was monitored through three linear variable displacement transducers (LVDT). The compressive strength and durability properties (i.e., porosity, resistance to chloride ion penetration, and capillary water absorption) were assessed using the same batch of concrete mix used to cast RC beams. The experimental results have shown that the flexural load of RC beams made with IFSSA was significantly higher than the control beam (100% FCBA). The increment of the flexural load was proportional to the content of IFSSA, with an increase of 27% for the beam made with 80% IFSSA than the control beam. The compressive strength of concrete increased by 56% and 61% for the concrete made with 80% and 100% IFSSA, respectively, than the control concrete, which is in good agreement with the flexural load of RC beams. Furthermore, the porosity, resistance to chloride ion penetration, and capillary water absorption were inversely proportional to the increase in the content of IFSSA. For instance, porosity, chloride penetration, and water absorption decreased by 43%, 54%, and 68%, respectively, when IFSSA entirely replaced FCBA. This decreasing percentage of durability properties is in agreement with the flexural load of RC beams. A good linear relationship of porosity with chloride penetration resistance and capillary water absorption was observed.

scholarly journals Effects of Imposed Damage on the Capillary Water Absorption of Recycled Aggregate Concrete

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Qi Gao ◽  
Zhiming Ma ◽  
Jianzhuang Xiao ◽  
Fuan Li
Keyword(s):  
Absorption Coefficient ◽  
Water Absorption ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Capillary Absorption ◽  
Capillary Water ◽  
Aggregate Concrete ◽  
Capillary Water Absorption ◽  
Freeze Thaw ◽  
Loading Level

Capillary water absorption of concrete is closely related to its pore structure, permeability, and durability. This paper intensively investigates the effects of imposed damage, including freeze-thaw damage and loading damage, on the capillary water absorption of recycled aggregate concrete (RAC). Freeze-thaw cycle test, loading test, and the experiment of capillary water absorption were carried out, respectively. The results demonstrate that the addition of recycled coarse aggregate (RCA) results in the increase in the capillary absorption behavior of RAC without imposed damage, and there exists a linear correlation between the behaviors of capillary water absorption and chloride penetration of RAC. The imposed freeze-thaw damage or load damage of RAC boosts with the increase of RCA replacement percentages after suffering the same freeze-thaw cycles or loading level. The imposed freeze-thaw damage and load damage further lead to the increase in the capillary water absorption of RAC, and the capillary absorption coefficient of RAC increases linearly with the increased RCA replacement percentages, after suffering the same freeze-thaw cycles or loading level. Furthermore, capillary absorption coefficient increases linearly with the growth of imposed freeze-thaw damage or load damage degree, which can be used to estimate the capillary absorption behavior of RAC exposed to the extreme environment.

scholarly journals The Influence of 30 Years Outdoor Weathering on the Durability of Hydrophobic Agents Applied on Obernkirchener Sandstones

Buildings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 18 ◽  
Author(s):  
Jeanette Orlowsky ◽  
Franziska Braun ◽  
Melanie Groh
Keyword(s):  
Water Absorption ◽  
Water Uptake ◽  
Capillary Water ◽  
Capillary Water Absorption ◽  
Absorption Determination ◽  
Colour Changes ◽  
Uptake Velocity ◽  
Outdoor Weathering

The durability of eleven different water repellents applied on one sandstone type was studied after a long-term weathering at seven different locations in Germany. By measuring colour changes, it could be shown that the formation of black crusts, the deposition of particles and biogenic growth caused a gradual darkening as well as significant changes in total colour over time. Additionally, the water absorption behaviour was investigated with two different methods: applying a low pressure using the pipe method and capillary water absorption measurements from a wet underlay. Afterwards, the test results were analysed with four different evaluation methods: calculation of the protection degree from pipe method and capillary water absorption, determination of the velocity of water uptake during capillary water absorption and calculation of the damaged depth of the stone surface using single-sided NMR technique. The growing damaged depth leads to an increase of the water uptake velocity and to a decrease of the protection degree of the applied hydrophobing agents. Three protective agents based on isobutyltrimethoxysilane showed already after two years of outdoor weathering a clear loss of performance, which significantly increased after 30 years of exposure.

The Effect of Steel Slag Coarse Aggregate on the Mechanical and Durability Performances of Concrete

2020 ◽  
Vol 833 ◽  
pp. 228-232
Author(s):  
Md. Jihad Miah ◽  
Mohammad Shamim Miah ◽  
Anisa Sultana ◽  
Taukir Ahmed Shamim ◽  
Md Ashraful Alom
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Experimental Investigations ◽  
Clay Brick ◽  
Crushing Strength ◽  
Burnt Clay ◽  
Good Agreement

This work performs experimental investigations on concrete made with difference replacement percentage of first-class burnt clay brick aggregate (0, 10, 20, 30, 40, 50, 60, 80, and 100%) by steel slag (SS) aggregate. The aim is to evaluate the mechanical properties as well as durability performances, additionally, water absorption porosity test is performed to investigate the influence of steel slag aggregate on the durability of tested concrete. The experimental results have shown that the compressive strength was improved significantly due to the replacement of brick aggregate by steel slag aggregate. The crushing strength of concrete made with 100% steel slag aggregate has gained up to 70% more than the control concrete (100% brick aggregate). However, the porosity of concrete was reduced with the adding percentage of brick aggregate by steel slag aggregate which is consistent with the compressive strength results. Further, a quite good agreement between compressive strength and porosity was observed as well.

scholarly journals Analysis of the Effect of Nano-SiO2 and Waterproofing Agent on the Water Transportation Process in Mortar Using NMR

2020 ◽  
Vol 10 (21) ◽  
pp. 7867
Author(s):  
Tao Meng ◽  
Huadong Wei ◽  
Kanjun Ying ◽  
Menghua Wang
Keyword(s):  
Water Absorption ◽  
Moisture Diffusion ◽  
Test Results ◽  
Capillary Water ◽  
Process Data ◽  
Capillary Water Absorption ◽  
Nano Sio2 ◽  
Water Transportation ◽  
Cement Based Materials ◽  
Transportation Process

Moisture diffusion in cement-based materials significantly impacts its durability. In this study, we analyzed the effect of adding a waterproofing agent and nano-SiO2 (NS) on the water transportation process in mortar using capillary water absorption tests and nuclear magnetic resonance (NMR) technology. The results indicate that the combined action of the waterproofing agent and nano-SiO2 drastically reduce the capillary water absorption coefficient and have a more significant impact than only adding the waterproofing agent. The moisture diffusion in different sections of the mortar during the water absorption process is obtained from the NMR test results and two function models. Comparative studies indicate that the NMR test results have good correlation with the capillary water absorption test results and provide accurate process data. The NMR analysis results offer a new analytical method to characterize the porosity of cement-based materials by continuously monitoring small-pitch sections.

Experimental Study on Sustainable Concrete with the Mixture of Low Calcium Fly Ash and Lime as a Partial Replacement of Cement

2011 ◽  
Vol 250-253 ◽  
pp. 307-312 ◽  
Author(s):  
Muthuramalingam Jayakumar ◽  
M. Salman Abdullahi
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Chloride Ion ◽  
Apparent Volume ◽  
Partial Replacement ◽  
Fly Ash Concrete ◽  
Low Calcium ◽  
Chloride Ion Penetration ◽  
Ion Penetration

Even though the use of fly ash in concrete is nowadays a common practice, its relatively slow pozzolanic reactivity hinders its greater utilization; hence efficient methods of activation are on demand. This study was carried out to evaluate the influence of lime as a chemical activator on the mechanical and durability properties of high strength fly ash concrete. Mixtures were made with 0, 30, 40, and 50% of cement replaced by low calcium fly ash. Corresponding mixtures were also made with the same amount of fly ash and addition of 10% of lime to each mixture. For each concrete mixture, slump, compressive strength, water absorption, sorptivity, apparent volume of permeable voids, and resistance to chloride-ion penetration were measured. The results obtained showed that addition of lime improved the compressive strength significantly at all ages. The strength of all the fly ash mixtures containing lime surpassed that of the corresponding Portland cement mix at 60 days. Addition of lime also improved the sorptivity and resistance to chloride-ion penetration of the fly ash concrete. It however increases the water absorption and the volume of permeable voids of the fly ash concrete.

Sign in / Sign up

Export Citation Format

Share Document