scholarly journals Manganese and Aluminium Recovery from Ferromanganese Slag and Al White Dross by a High Temperature Smelting-Reduction Process

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 405
Author(s):  
Artur Kudyba ◽  
Jafar Safarian
Keyword(s):  
High Temperature ◽  
Slag Phase ◽  
Elevated Temperatures ◽  
Reduction Process ◽  
Complete Recovery ◽  
Aluminum Production ◽  
Smelting Reduction ◽  
Equilibrium Study ◽  
Lower Viscosity

The recovery of Mn and Al from two industrial waste of ferromanganese and aluminum production processes was investigated via implementing a high temperature smelting—aluminothermic reduction process. The experiments were carried out with or without CaO flux addition, and two dross qualities. It was observed that the prepared mixtures of the materials yield homogeneous metal and slag products in terms of chemical composition and the distribution of phases. However, the separation of produced metal phase from the slag at elevated temperatures occurs when a higher amount of CaO is added. Viscosity calculations and equilibrium study indicated that the better metal and slag separation is obtained when the produced slag has lower viscosity and lower liquidus. It was found that the process yields Al-Mn-Si alloys, and it is accompanied with complete recovery of Mn, Si and Fe and the unreacted Al in the process. Moreover, the quality of metal product was less dependent on the slightly different dross quality, and the concentration of minor Ca in metal is slightly increased with significant increase of CaO in the slag phase.

Gate Stack Engineering for High Temperature Silicon Carbide CMOS ICs

2015 ◽  
Vol 2015 (HiTEN) ◽  
pp. 000033-000036 ◽  
Author(s):  
M.H. Weng ◽  
A.D. Murphy ◽  
D.T. Clark ◽  
D.A. Smith ◽  
R.F. Thompson ◽  
...  
Keyword(s):  
Silicon Carbide ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Systematic Evaluation ◽  
Process Conditions ◽  
Operating Characteristics ◽  
Gate Stack ◽  
Metal Insulator ◽  
Semiconductor Interfaces

The potential to thermally grow SiO2 on silicon carbide has resulted in it becoming the technology of choice to realise high temperature CMOS circuits. The challenge to achieve a high quality gate stack relies on engineering the metal-insulator-semiconductor interfaces to enable reliable high temperature functionality. Here we describe the effect of different process conditions for the formation of the dielectric layer on the characteristics of the resulting devices. The operating characteristics at elevated temperatures depend critically on the quality of the gate stack. Therefore a systematic evaluation of the intrinsic properties of the gate stack and data from reliability tests are needed.

High-Temperature Instability of A Cr2Nb-Nb(Cr) Microlaminate Composite

1996 ◽  
Vol 54 ◽  
pp. 374-375
Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Aircraft Engine ◽  
Lattice Parameter ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Cross Sectional ◽  
Bcc Structure

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.

Phase transformation and layer evolution in molybdenum disilicide-silicon carbide nanolayered coatings

1994 ◽  
Vol 52 ◽  
pp. 538-539
Author(s):  
H. Kung ◽  
T. R. Jervis ◽  
J.-P. Hirvonen ◽  
M. Nastasi ◽  
T. E. Mitchell ◽  
...  
Keyword(s):  
Phase Transformation ◽  
High Temperature ◽  
Oxidation Resistance ◽  
Elevated Temperatures ◽  
Matrix Material ◽  
Molybdenum Disilicide ◽  
High Temperature Strength ◽  
Cross Sectional ◽  
Good Oxidation Resistance ◽  
Structural Applications

MoSi2 is a potential matrix material for high temperature structural composites due to its high melting temperature and good oxidation resistance at elevated temperatures. The two major drawbacksfor structural applications are inadequate high temperature strength and poor low temperature ductility. The search for appropriate composite additions has been the focus of extensive investigations in recent years. The addition of SiC in a nanolayered configuration was shown to exhibit superior oxidation resistance and significant hardness increase through annealing at 500°C. One potential application of MoSi2- SiC multilayers is for high temperature coatings, where structural stability ofthe layering is of major concern. In this study, we have systematically investigated both the evolution of phases and the stability of layers by varying the heat treating conditions.Alternating layers of MoSi2 and SiC were synthesized by DC-magnetron and rf-diode sputtering respectively. Cross-sectional transmission electron microscopy (XTEM) was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: crystallization and phase transformation of MoSi2, crystallization of SiC, and spheroidization of the layer structures.

INFLUENCE OF FORCED CONVECTION IN LIQUID INSIDE THE TIN ON DURATION OF STERILIZATION IN THE COURSE OF FISH PROCESSING

2017 ◽  
pp. 137-144
Author(s):  
Gennadiy Valentinovich Alexeev ◽  
Elena Igorevna Verboloz
Keyword(s):  
High Temperature ◽  
Liquid Phase ◽  
Forced Convection ◽  
Thermal Process ◽  
Processing Time ◽  
Fish Processing ◽  
Study Results ◽  
Equipment Modernization ◽  
Bottom To Top

The article focuses on the process of intensive mixing of liquid phase in the tin during high-temperature sterilization, i.e. sterilization when temperature of the heat carrier reaches 150-160°C. It has been stated that for intensification of the thermal process during sterilization of tinned fish with liquid filling it is preferable to turn a tin from bottom to top. This operation helps to increase the driving power of the process and to shorten warming time. Besides, high-temperature sterilization carried out according to experimental modes, where the number of tin turnovers is calculated, greatly shortens processing time and improves quality of the product. In this case there is no superheating, all tins are evenly heated. The study results will contribute to equipment modernization and to preserving valuable food qualities.

Experience in the use of double broncholytic therapy in occupational practice

2019 ◽  
pp. 303-307
Author(s):  
Elena A. Beigel ◽  
Natalya G. Kuptsova ◽  
Elena V. Katamanova ◽  
Oksana V. Ushakova ◽  
Oleg L. Lakhman
Keyword(s):  
Quality Of Life ◽  
Personal Data ◽  
The Body ◽  
Step Test ◽  
Aluminum Production ◽  
Chronic Obstructive ◽  
Body Plethysmography ◽  
Occupational Copd ◽  
The Impact

Introduction. Occupational chronic obstructive pulmonary disease (COPD) is one of the leading nosological forms of occupational respiratory disease. Numerous studies have shown high effectiveness of the combination of indacaterol/glycopyrronium (Ultibro®breezhaler®) on the impact on clinical and functional indicators in the treatment of COPD in General practice.The aim of the investigation the case of occupational COPD with the analysis of the dynamics of functional indicators, tolerance to physical load and evaluation of the quality of life of workers engaged in aluminum production by using combination of indacaterol/glycopyrronium.Materials and methods. The random sampling method included 20 men, workers of aluminum production, with the established diagnosis of professional COPD at the age of 40 to 60 years. The survey was conducted (Borg scale, medical Research Council scale (mMRC) and COPD Assessment Test (CAT). Functional methods of studies were conducted: spirometry, body plethysmography, electrocardiography (ECG) and the six-minute stepper test (6-MST).Results. Against the background of 8 weeks of therapy, the volume of forced exhalation for 1 minute (FEV1) increased by 14.7% and amounted to 67.90% of the due values, the forced vital capacity of the lungs (FVC) increased by 11.3% and amounted to 76.95% of the due. According to the body plethysmography (BPG) is set to decrease in residual lung volume on average by 13.4% and static hyperinflation, confirmed by the decrease in functional residual volume (FRV) of 18.8%. During the study period increased physical activity of patients. The average difference between the distance traveled in the six-minute step test before and after treatment was 58.8 m. The analysis of personal data showed that the quality of life of patients improved, the total score in the questionnaire CAT at the beginning of the study was 16.9 points, and after 8 weeks decreased by 63% and amounted to 10.7 points.Conclusions: The Results indicate a positive effect of combination therapy with indacaterol/glycopyrronium on the course and progression of occupational COPD.

WIELAND-K88

Alloy Digest ◽  
2005 ◽  
Vol 54 (12) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Stress Relaxation ◽  
Copper Alloy ◽  
Elevated Temperatures ◽  
Heat Treating ◽  
Relaxation Resistance ◽  
Temperature Performance ◽  
Very High

Abstract Wieland K-88 is a copper alloy with very high electrical and thermal conductivity, good strength, and excellent stress relaxation resistance at elevated temperatures. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CU-738. Producer or source: Wieland Metals Inc.

DOWMETAL HZ32XA

Alloy Digest ◽  
1956 ◽  
Vol 5 (7) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Creep Resistance ◽  
Zirconium Alloy ◽  
Elevated Temperatures ◽  
Heat Treating ◽  
High Temperature Creep ◽  
Aged Condition ◽  
Chemical Company ◽  
Temperature Performance

Abstract DOWMETAL HZ32XA is a magnesium-thorium-zinc-zirconium alloy having good high temperature creep resistance, and is recommended for applications at elevated temperatures. It is used in the artificially aged condition (T5). This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance as well as heat treating, machining, and joining. Filing Code: Mg-26. Producer or source: The Dow Chemical Company.

UDIMET 105

Alloy Digest ◽  
1972 ◽  
Vol 21 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Surface Treatment ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
Heat Treating ◽  
Nickel Base Alloy ◽  
Temperature Performance ◽  
Nickel Base

Abstract UDIMET 105 is a nickel-base alloy which was developed for service at elevated temperatures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-175. Producer or source: Special Metals Corporation.

CARPENTER L-605 ALLOY

Alloy Digest ◽  
1987 ◽  
Vol 36 (8) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Temperature Performance ◽  
Cobalt Base Alloy ◽  
Cobalt Base ◽  
Oxidation And Corrosion

Abstract CARPENTER L-605 alloy is a nonmagnetic cobalt-base alloy that has good oxidation and corrosion resistance and high strength at elevated temperatures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep and fatigue. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Co-81. Producer or source: Carpenter.

FANSTEEL 85 METAL

Alloy Digest ◽  
1981 ◽  
Vol 30 (6) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Creep Strength ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
Heat Treating ◽  
Good Combination ◽  
Bend Strength ◽  
Temperature Performance

Abstract FANSTEEL 85 METAL is a columbium-base alloy characterized by good fabricability at room temperature, good weldability and a good combination of creep strength and oxidation resistance at elevated temperatures. Its applications include missile and rocket components and many other high-temperature parts. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and bend strength as well as creep. It also includes information on low and high temperature performance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Cb-7. Producer or source: Fansteel Metallurgical Corporation. Originally published December 1963, revised June 1981.

Sign in / Sign up

Export Citation Format

Share Document