scholarly journals A Theoretical Analysis of Profile Conformance Improvement Due to Suspension Injection

Mathematics ◽  
2021 ◽  
Vol 9 (15) ◽  
pp. 1727
Author(s):  
Konstantin Mikhailovich Fedorov ◽  
Alexander Yanovich Gilmanov ◽  
Alexander Pavlovich Shevelev ◽  
Alexander Vyacheslavovich Kobyashev ◽  
Denis Alekseevich Anuriev
Keyword(s):  
Penetration Depth ◽  
Water Injection ◽  
Filtration Coefficient ◽  
Mean Values ◽  
Injection Process ◽  
Particle Penetration ◽  
Before And After ◽  
Complex Criterion ◽  
Suspension Filtration ◽  
Maximum Penetration

This study is focused on a solution for the problem of suspension penetration in a porous formation. Such a solution forms the basis of injection profile diversion technology for oil reservoir sweep improvement. A conventional model of deep-bed suspension flow was used to describe the suspension injection process. The suspension slug was followed by water injection, and the inflow injection profile before and after treatment was investigated. For the first time, the criteria that determine the effectiveness of the inflow profile improvement process are introduced. The effect of the suspension filtration coefficient on the particle penetration depth was studied. A specific filtration coefficient value for the maximum penetration depth was achieved. The obtained analytical solution was generalized on multi-reservoir strata with poor interlayer crosslinking. The efficiency of profile conformance improvement was described by the differences in the root-mean-square deviations of the inflow velocities in interlayers from mean values before and after the treatment. It was shown that the complex criterion of suspension treatment efficiency should include a reduction in total injectivity. An increase in suspension slug volume improves the injectivity profile but decreases the total injectivity of an injector.

ENDOCRINE CHANGES BEFORE AND AFTER THE MENARCHE

1973 ◽  
Vol 74 (4) ◽  
pp. 685-694 ◽  
Author(s):  
B.-A. Lamberg ◽  
R.-L. Kantero ◽  
P. Saarinen ◽  
O. Widholm
Keyword(s):  
Binding Proteins ◽  
Maturation Process ◽  
Hormone Binding ◽  
Maximal Level ◽  
Continuous Increase ◽  
Mean Values ◽  
Thyroxine Binding Globulin ◽  
Before And After ◽  
Free Thyroxine Index ◽  
Level 1

ABSTRACT In an endocrine survey of healthy girls aged 8 to 20 years before and after the menarche, the serum thyroxine (T4), uptake of triiodothyronine by Sephadex (T3U), and the binding capacities of thyroxine binding globulin (TBG) and pre-albumin (TBPA) were measured, and a free thyroxine index (FTI = T4 × T3U) was calculated. The subjects were grouped according to skeletal age (SA) until the menarche and after this in the post-menarcheal age (PMA), expressed in years. T4 and FTI increased concomitantly and reached peak values of 8.40 μg/100 ml and 8.40, respectively, at 2–3 years PMA. The corresponding mean values for post-menarcheal girls (7.74 μg/100 ml and 7.51) differed statistically significantly from the means before the menarche (7.03 μg/ 100 ml and 6.75). The TBG remained virtually unchanged during the whole period, whereas the TBPA showed a continuous increase and reached a maximal level 1–2 years after the menarche. The maturation process in girls in some way involves an increase in the total and free T4 level which is not dependent on hormone binding proteins.

Sensitivity of bioelectrical impedance to detect changes in human body composition

1989 ◽  
Vol 67 (4) ◽  
pp. 1643-1648 ◽  
Author(s):  
R. Ross ◽  
L. Leger ◽  
P. Martin ◽  
R. Roy
Keyword(s):  
Body Composition ◽  
Human Body ◽  
Correlation Coefficients ◽  
Bioelectrical Impedance ◽  
Mean Values ◽  
Significance Level ◽  
Exercise Regimen ◽  
Before And After ◽  
Hydrostatic Weighing ◽  
Human Body Composition

The purpose of this study was to compare the estimates of lean body mass (LBM) and percent body fat (%BF), as predicted by bioelectrical impedance (BIA) and sum of skinfolds (SF), with those derived by hydrostatic weighing (HW) obtained before and after a 10-wk diet and exercise regimen. The experimental (E) group consisted of 17 healthy male subjects; 20 healthy males served as the control (C) group. Post hoc Scheffe contrasts computed on E group data indicated that, for both LBM and %BF, the Lukaski and Segal BIA equations, as well as the Durnin SF equation, derived mean values that were not significantly different (0.05 significance level) from HW in both pre- and postregimen conditions. For LBM, the same equations derived the following significant (P less than 0.01) correlation coefficients for both pre- and postregimen data: Lukaski, 0.87 and 0.85; Segal, 0.89 and 0.87; and Durnin, 0.90 and 0.88. For %BF, the correlation coefficients were slightly lower but remained statistically significant (P less than 0.01). The findings of this study suggest that the BIA method, by use of either the Lukaski or Segal prediction equations, is a valid means of predicting changes in human body composition as measured by the Siri transformation of body density.

Model of water injection process during closed phase of spark ignition engine

Energy ◽  
2019 ◽  
Vol 174 ◽  
pp. 1121-1132 ◽  
Author(s):  
Jair Leopoldo Loaiza Bernal ◽  
Janito Vaqueiro Ferreira
Keyword(s):  
Water Injection ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Injection Process

scholarly journals Numerical Simulation and Engineering Application of Coalbed Water Injection

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Yijie Shi ◽  
Pengfei Wang ◽  
Ronghua Liu ◽  
Xuanhao Tan ◽  
Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Water Injection ◽  
Engineering Application ◽  
Working Environment ◽  
Engineering Practice ◽  
Characteristic Parameters ◽  
Injection Process ◽  
Working Face ◽  
Dust Reduction

Coalbed water injection is the most basic and effective dust-proof technology in the coal mining face. To understand the influence of coalbed water injection process parameters and coalbed characteristic parameters on coal wetting radius, this paper uses Fluent computational fluid dynamics software to systematically study the seepage process of coalbed water injection under different process parameters and coalbed characteristic parameters, calculation results of which are applied to engineering practice. The results show that the numerical simulation can help to predict the wetness range of coalbed water injection, and the results can provide guidance for the onsite design of coalbed water injection process parameters. The effect of dust reduction applied to onsite coalbed water injection is significant, with the average dust reduction rates during coal cutting and support moving being 67.85% and 46.07%, respectively, which effectively reduces the dust concentration on the working face and improves the working environment.

The Water Injection Process

2003 ◽  
Vol 81 (3) ◽  
pp. 333-341 ◽  
Author(s):  
B. Palsson ◽  
D.R. Davies ◽  
A.C. Todd ◽  
J.M. Somerville
Keyword(s):  
Water Injection ◽  
Injection Process

scholarly journals Influence of Apical Patency and Cleaning of the Apical Foramen on Periapical Extrusion in Retreatment

2013 ◽  
Vol 24 (5) ◽  
pp. 482-486 ◽  
Author(s):  
Marili Doro Andrade Deonizio ◽  
Gilson Blitzkow Sydney ◽  
Antonio Batista ◽  
Roberto Pontarolo ◽  
Paulo Ricardo Bittencourt Guimarães ◽  
...  
Keyword(s):  
Material Removal ◽  
Filling Material ◽  
Mean Values ◽  
Filtration System ◽  
Root Canal Retreatment ◽  
Significant Difference ◽  
Before And After ◽  
The Mean ◽  
The Difference ◽  
Removal Technique

This study evaluated the influence of apical patency, root filling removal technique and cleaning of the apical foramen, concerning the amount of debris extruded during root canal retreatment. Forty mandibular incisors were randomly assigned to 4 groups - GIM (n=10), GIIM (n=10), GIPT (n=10) and GIIPT (n=10), which were named according to leaving (I) or not (II) apical patency during canal preparation and filling removal technique (manual - M or ProTaper system - PT). After filling material removal, each specimen of each group had the apical foramen cleaned by sizes 15, 20 and 25 instruments, generating 12 subgroups: GIM15, GIM20, GIM25, GIIM15, GIIM20, GIIM25, GIPT15, GIPT20, GIPT25, GIIPT15, GIIPT20 and GIIPT25. Extruded filling debris was collected by a Milipore filtration system, an HV-durapore, 0.45 µm pore filter with a 25 mm diameter. The filters were weighed before and after the collection on an analytical scale (10–5 g), and the difference was calculated. The mean weight of extruded filling debris was analyzed statistically by Kruskal-Wallis and Friedman ANOVA tests (α=0.05). The mean values found in the groups (in mg) were: GIM (0.95±0.94), GIIM (0.47±0.62), GIPT (0.30±0.31) and GIIPT (0.32±0.44). There was no statistically significant difference among any of the groups or subgroups (p>0.05). ProTaper provided the smallest amount of extruded filling material, regardless of presence or absence of apical patency, followed by manual technique, without and with apical patency. Additional amounts of debris were collected during cleaning of the apical foramen, regardless of the instrument, presence/absence of patency or root filling removal technique.

Effect of induced metabolic acidosis on intracellular pH, buffer capacity and contraction force of human skeletal muscle

1985 ◽  
Vol 69 (5) ◽  
pp. 505-510 ◽  
Author(s):  
E. Hultman ◽  
S. Del Canale ◽  
H. Sjöholm
Keyword(s):  
Buffer Capacity ◽  
Recovery Period ◽  
Mean Values ◽  
Muscle Ph ◽  
Before And After ◽  
Ph Buffer ◽  
Total Capacity ◽  
Ph Decrease ◽  
Muscle Biopsies

1. Five volunteers were studied before and after oral administration of NH4Cl (0.3 g/kg body wt.) given in order to create a moderate acidosis. 2. The quadriceps femoris muscles were stimulated electrically for 75 s and muscle biopsies for determination of pH and metabolite content were taken before, at the end of contraction and after 10 min in the recovery period. 3. Muscle pH at rest (mean 7.04) was not significantly decreased after acidification despite an extracellular pH decrease of 0.15 unit. 4. After contraction muscle pH was significantly lower after NH4Cl. Mean values before and after acidification were 6.70 and 6.54 respectively. 5. The buffer capacity calculated as the total capacity of the muscle to buffer H+ produced during the isometric contraction before and after NH4Cl ingestion was reduced from 68.6 sl to 54.5 sl. 6. The force produced by contracting muscle was significantly lower at the end of the contraction period after NH4Cl ingestion, 44.6% of initial compared with 55.4% without NH4Cl.

Effect of Incisions in the Brainstem Commissural Network on the Short-Term Vestibulo-Ocular Adaptation of the CAT

1991 ◽  
Vol 1 (3) ◽  
pp. 223-239
Author(s):  
G. Cheron
Keyword(s):  
Low Frequency ◽  
Adaptive Plasticity ◽  
Training Procedure ◽  
Optokinetic Response ◽  
Mean Values ◽  
Ocular Reflex ◽  
Optokinetic Reflex ◽  
Before And After ◽  
Vestibulo Ocular Reflex ◽  
Vor Adaptation

This study was intended to test the adaptive plasticity of the vestibulo-ocular reflex before and after either a midsagittal or parasagittal incision in the brainstem. Eye movements were measured with the electromagnetic search coil technique during the vestibulo-ocular reflex (VORD) in the dark, the optokinetic reflex (OKN), and the visuo-vestibular adaptive training procedure. Two types of visual-vestibular combined stimulation were applied by means of low frequency stimuli (0.05 to 0.10 Hz). In order to increase or decrease the VORD gain, the optokinetic drum was oscillated either 180∘ out-of-phase or in-phase with the vestibular stimulus turntable. This “training” procedure was applied for 4 hours. Initial measurements of the VORD were normal with a mean gain value of 0.92 ± 0.08. After 4 hours of “training” with the out-of-phase condition (180∘), VORD gain reached mean values of 1.33 ± 0.11 (n = 6 cats). In the in-phase combination, the mean VORD gain decreased from 1.0 to 0.63 ± 0.02 (n = 2 cats). No significant change of VORD phase was found in any of the cats. Midsagittal or parasagittal pontomedullary brainstem incisions were performed in 4 cats. Recovery of the VOR was tested on the 2nd, 7th, and 30th day after operation. After the 30th day, recovery of the VORD gain stabilized at about 66% of the initial preoperative value. At this stage of the recovery, the optokinetic response (OKN) of the midsagittal-Iesioned cats was practically normal: in the parasagittal-Jesioned cats, the postoperative OKN responses were asymmetric. After stabilization of recovery, lesioned cats were trained with the same adaptation procedure. Although the direct effect of the visuo-vestibular combined stimulation during the training was still operative in all lesioned cats, the adaptive plasticity was completely abolished by the lesions. These results suggest that the commissural brainstem network may play a crucial role in the acquisition of the forced VOR adaptation.

Transforming Water Injection Process With Real Time Automation

2021 ◽  
Author(s):  
Muhammad Zakwan Mohd Sahak ◽  
Eugene Castillano ◽  
Tengku Amansyah Tuan Mat ◽  
Maung Maung Myo Thant
Keyword(s):  
Oil Recovery ◽  
Capital Investment ◽  
Water Injection ◽  
Optimal Operation ◽  
Near Miss ◽  
Injection System ◽  
Injection Technique ◽  
Manual Operation ◽  
Injection Process ◽  
Oil Rim

Abstract For mature fields, water injection is one of the widely deployed techniques to ensure continuous oil recovery from the reservoir by maintaining the reservoir pressure, oil rim and pushing the oil from injection to production wells. Thus, it is critical to ensure a continuous and reliable operation of water injection to have consistent and sustainable rate. This paper demonstrates the new approach, utilizing automation and digital technology providing operational improvement and reduction in unplanned production deferment (UPD). One of the methods to effectively manage the water injection operation is via automation of injection process, especially since most of the water injection facilities still rely heavily on manual operation. First, a discussion on typical water injection technique is discussed. Challenges and sub-optimal operation of water injection processes within the company and industry are analysed. Then, the designing of a fully automated water injection system, such as equipment availability and constraints in matching and responding to well injection requirement are demonstrated. While an immediate adoption of process automation to mature assets may be faced with challenges such as system readiness, hardware availability, capital investment and mindset change, a step-by-step approach such as guided operation and semi-auto operation is explored as preparation prior to a full automation roll-out. With the shift from manual operation reliance to automation, the response time to process changes is improved leading to reduction in near-miss and trip cases, and minimum unplanned deferment.

Sign in / Sign up

Export Citation Format

Share Document