scholarly journals Fabrication of Suspended PMMA-Graphene Membrane for High Sensitivity LC-MEMS Pressure Sensor

Membranes ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 996
Author(s):  
Norliana Yusof ◽  
Badariah Bais ◽  
Jumril Yunas ◽  
Norhayati Soin ◽  
Burhanuddin Yeop Majlis
Keyword(s):  
Pressure Sensor ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Low Pressure ◽  
Sensor Applications ◽  
Deformable Structure ◽  
Response To Change ◽  
Electrical Wiring ◽  
Implantable Sensor

The LC-MEMS pressure sensor is an attractive option for an implantable sensor. It senses pressure wirelessly through an LC resonator, eliminating the requirement for electrical wiring or a battery system. However, the sensitivity of LC-MEMS pressure sensors is still comparatively low, especially in biomedical applications, which require a highly-sensitive sensor to measure low-pressure variations. This study presents the microfabrication of an LC wireless MEMS pressure sensor that utilizes a PMMA-Graphene (PMMA/Gr) membrane supported on a silicon trench as the deformable structure. The (PMMA/Gr) membrane was employed to increase the sensor’s sensitivity due to its very low elastic modulus making it easy to deform under extremely low pressure. The overall size of the fabricated sensor was limited to 8 mm × 8 mm. The experimental results showed that the capacitance value changed from 1.64 pF to 12.32 pF when the applied pressure varied from 0 to 5 psi. This capacitance variation caused the frequency response to change from 28.74 MHz to 78.76 MHz. The sensor sensitivity was recorded with a value of 193.45 kHz/mmHg and a quality factor of 21. This study concludes that the (PMMA/Gr) membrane-based LC-MEMS pressure sensor has been successfully designed and fabricated and shows good potential in biomedical sensor applications.

scholarly journals Highly-Sensitive Textile Pressure Sensors Enabled by Suspended-Type All Carbon Nanotube Fiber Transistor Architecture

Micromachines ◽  
2020 ◽  
Vol 11 (12) ◽  
pp. 1103
Author(s):  
Jae Sang Heo ◽  
Keon Woo Lee ◽  
Jun Ho Lee ◽  
Seung Beom Shin ◽  
Jeong Wan Jo ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Pressure Sensor ◽  
Pressure Range ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Low Pressure ◽  
Electronic Textiles ◽  
Carbon Nanotube Fiber ◽  
Cnt Fiber ◽  
Walled Carbon Nanotubes

Among various wearable health-monitoring electronics, electronic textiles (e-textiles) have been considered as an appropriate alternative for a convenient self-diagnosis approach. However, for the realization of the wearable e-textiles capable of detecting subtle human physiological signals, the low-sensing performances still remain as a challenge. In this study, a fiber transistor-type ultra-sensitive pressure sensor (FTPS) with a new architecture that is thread-like suspended dry-spun carbon nanotube (CNT) fiber source (S)/drain (D) electrodes is proposed as the first proof of concept for the detection of very low-pressure stimuli. As a result, the pressure sensor shows an ultra-high sensitivity of ~3050 Pa−1 and a response/recovery time of 258/114 ms in the very low-pressure range of <300 Pa as the fiber transistor was operated in the linear region (VDS = −0.1 V). Also, it was observed that the pressure-sensing characteristics are highly dependent on the contact pressure between the top CNT fiber S/D electrodes and the single-walled carbon nanotubes (SWCNTs) channel layer due to the air-gap made by the suspended S/D electrode fibers on the channel layers of fiber transistors. Furthermore, due to their remarkable sensitivity in the low-pressure range, an acoustic wave that has a very tiny pressure could be detected using the FTPS.

scholarly journals Modeling of a square-shape ZnO, ZnS and AlN membrane for mems capacitive pressure-sensor applications

2020 ◽  
Vol 11 ◽  
pp. 14
Author(s):  
Ahmad Dagamseh ◽  
Qais Al-Bataineh ◽  
Zaid Al-Bataineh ◽  
Nermeen S. Daoud ◽  
Ahmad Alsaad ◽  
...  
Keyword(s):  
Thermal Stress ◽  
Pressure Sensor ◽  
Membrane Structure ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Membrane Thickness ◽  
Capacitive Pressure Sensor ◽  
The Finite Element Method ◽  
Sensor Applications ◽  
Opposite Behavior

In this paper, mathematical modeling and simulation of a MEMS-based clamped square-shape membrane for capacitive pressure sensors have been performed. Three types of membrane materials were investigated (i.e. Zinc Oxide (ZnO), Zinc Sulfide (ZnS) and Aluminum Nitride (AlN)). Various performance parameters such as capacitance changes, deflection, nonlinearity, the sensitivity of the membrane structure for different materials and film-thicknesses have been considered using the Finite Element Method (FEM) and analytically determined using the FORTRAN environment. The simulation model outperforms in terms of the effective capacitance value. The results show that the membrane deflection is linearly related to the applied pressure. The ZnS membrane provides a capacitance of 0.023 pico-Farad at 25 kPa with a 42.5% relative capacitance changes to reference capacitance. Additionally, the results show that for ZnO and AlN membranes the deflection with no thermal stress is higher than that with thermal stress. However, an opposite behavior for the ZnS membrane structure has been observed. The mechanical and capacitance sensitivities are affected by the membrane thickness as the capacitance changes are inversely proportional to the membrane thickness. Such results open possibilities to utilize various materials for pressure sensor applications by means of the capacitance-based detection technique.

scholarly journals Flexible Wireless Passive LC Pressure Sensor with Design Methodology and Cost-Effective Preparation

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 976
Author(s):  
Zhuqi Sun ◽  
Haoyu Fang ◽  
Baochun Xu ◽  
Lina Yang ◽  
Haoran Niu ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
Electronic Device ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Capacitive Pressure Sensor ◽  
Intimate Contact ◽  
Physical Motion ◽  
Readout Device ◽  
Wearable Electronic Device

Continuous monitoring of physical motion, which can be successfully achieved via a wireless flexible wearable electronic device, is essential for people to ensure the appropriate level of exercise. Currently, most of the flexible LC pressure sensors have low sensitivity because of the high Young’s modulus of the dielectric properties (such as PDMS) and the inflexible polymer films (as the substrate of the sensors), which don’t have excellent stretchability to conform to arbitrarily curved and moving surfaces such as joints. In the LC sensing system, the metal rings, as the traditional readout device, are difficult to meet the needs of the portable readout device for the integrated and planar readout antenna. In order to improve the pressure sensitivity of the sensor, the Ecoflex microcolumn used as the dielectric of the capacitive pressure sensor was prepared by using a metal mold copying method. The Ecoflex elastomer substrates enhanced the levels of conformability, which offered improved capabilities to establish intimate contact with the curved and moving surfaces of the skin. The pressure was applied to the sensor by weights, and the resonance frequency curves of the sensor under different pressures were obtained by the readout device connected to the vector network analyzer. The experimental results show that resonant frequency decreases linearly with the increase of applied pressure in a range of 0–23,760 Pa with a high sensitivity of −2.2 MHz/KPa. We designed a coplanar waveguide-fed monopole antenna used to read the information of the LC sensor, which has the potential to be integrated with RF signal processing circuits as a portable readout device and a higher vertical readout distance (up to 4 cm) than the copper ring. The flexible LC pressure sensor can be attached to the skin conformally and is sensitive to limb bending and facial muscle movements. Therefore, it has the potential to be integrated as a body sensor network that can be used to monitor physical motion.

Development of circuit solution and design of capacitive pressure sensor array for applied robotics

2020 ◽  
Vol 8 (4) ◽  
pp. 296-307
Author(s):  
Konstantin Krestovnikov ◽  
Aleksei Erashov ◽  
Аleksandr Bykov
Keyword(s):  
Pressure Sensor ◽  
Output Signal ◽  
Sensor Array ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Fine Tuning ◽  
Capacitive Pressure Sensor ◽  
Cell Parameters ◽  
Linear Pattern ◽  
Sensor Structure

This paper presents development of pressure sensor array with capacitance-type unit sensors, with scalable number of cells. Different assemblies of unit pressure sensors and their arrays were considered, their characteristics and fabrication methods were investigated. The structure of primary pressure transducer (PPT) array was presented; its operating principle of array was illustrated, calculated reference ratios were derived. The interface circuit, allowing to transform the changes in the primary transducer capacitance into voltage level variations, was proposed. A prototype sensor was implemented; the dependency of output signal power from the applied force was empirically obtained. In the range under 30 N it exhibited a linear pattern. The sensitivity of the array cells to the applied pressure is in the range 134.56..160.35. The measured drift of the output signals from the array cells after 10,000 loading cycles was 1.39%. For developed prototype of the pressure sensor array, based on the experimental data, the average signal-to-noise ratio over the cells was calculated, and equaled 63.47 dB. The proposed prototype was fabricated of easily available materials. It is relatively inexpensive and requires no fine-tuning of each individual cell. Capacitance-type operation type, compared to piezoresistive one, ensures greater stability of the output signal. The scalability and adjustability of cell parameters are achieved with layered sensor structure. The pressure sensor array, presented in this paper, can be utilized in various robotic systems.

CMOS-MEMS Based Current Mirror MOSFET Embedded Pressure Sensor for Healthcare and Biomedical Applications

2013 ◽  
Vol 647 ◽  
pp. 315-320 ◽  
Author(s):  
Pradeep Kumar Rathore ◽  
Brishbhan Singh Panwar
Keyword(s):  
Pressure Sensor ◽  
Biomedical Applications ◽  
Circuit Simulation ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Cmos Technology ◽  
Current Mirror ◽  
Sensing Element ◽  
Pressure Sensing ◽  
Cmos Mems

This paper reports on the design and optimization of current mirror MOSFET embedded pressure sensor. A current mirror circuit with an output current of 1 mA integrated with a pressure sensing n-channel MOSFET has been designed using standard 5 µm CMOS technology. The channel region of the pressure sensing MOSFET forms the flexible diaphragm as well as the strain sensing element. The piezoresistive effect in MOSFET has been exploited for the calculation of strain induced carrier mobility variation. The output transistor of the current mirror forms the active pressure sensing MOSFET which produces a change in its drain current as a result of altered channel mobility under externally applied pressure. COMSOL Multiphysics is utilized for the simulation of pressure sensing structure and Tspice is employed to evaluate the characteristics of the current mirror pressure sensing circuit. Simulation results show that the pressure sensor has a sensitivity of 10.01 mV/MPa. The sensing structure has been optimized through simulation for enhancing the sensor sensitivity to 276.65 mV/MPa. These CMOS-MEMS based pressure sensors integrated with signal processing circuitry on the same chip can be used for healthcare and biomedical applications.

scholarly journals Alcohol-based highly conductive polymer for conformal nanocoatings on hydrophobic surfaces toward a highly sensitive and stable pressure sensor

2020 ◽  
Vol 12 (1) ◽  
Author(s):  
Jung Joon Lee ◽  
Srinivas Gandla ◽  
Byeongjae Lim ◽  
Sunju Kang ◽  
Sunyoung Kim ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
Mechanical Stability ◽  
Exchange Process ◽  
Conductive Polymer ◽  
High Sensitivity ◽  
Fast Response ◽  
Pdms Surface ◽  
Practical Applications ◽  
Sensor Applications ◽  
Water Based

Abstract Conformal and ultrathin coating of highly conductive PEDOT:PSS on hydrophobic uneven surfaces is essential for resistive-based pressure sensor applications. For this purpose, a water-based poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) solution was successfully exchanged to an organic solvent-based PEDOT:PSS solution without any aggregation or reduction in conductivity using the ultrafiltration method. Among various solvents, the ethanol (EtOH) solvent-exchanged PEDOT:PSS solution exhibited a contact angle of 34.67°, which is much lower than the value of 96.94° for the water-based PEDOT:PSS solution. The optimized EtOH-based PEDOT:PSS solution exhibited conformal and uniform coating, with ultrathin nanocoated films obtained on a hydrophobic pyramid polydimethylsiloxane (PDMS) surface. The fabricated pressure sensor showed high performances, such as high sensitivity (−21 kPa−1 in the low pressure regime up to 100 Pa), mechanical stability (over 10,000 cycles without any failure or cracks) and a fast response time (90 ms). Finally, the proposed pressure sensor was successfully demonstrated as a human blood pulse rate sensor and a spatial pressure sensor array for practical applications. The solvent exchange process using ultrafiltration for these applications can be utilized as a universal technique for improving the coating property (wettability) of conducting polymers as well as various other materials.

Micromachined Pressure Sensors on Optical Fiber Tip

2009 ◽  
Vol 74 ◽  
pp. 149-152
Author(s):  
X.M. Zhang ◽  
M. Yu ◽  
Silas Nesson ◽  
H. Bae ◽  
A. Christian ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Pressure Sensor ◽  
Linear Response ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Outer Diameter ◽  
Sensor Element ◽  
Batch Fabrication ◽  
In Vitro Measurements

This paper reports the development of a miniature pressure sensor on the optical fiber tip for in vitro measurements of rodent intradiscal pressure. The sensor element is biocompatible and can be fabricated by simple, batch-fabrication methods in a non-cleanroom environment with good device-to-device uniformity. The fabricated sensor element has an outer diameter of only 366 μm, which is small enough to be inserted into the rodent discs without disrupting the structure or altering the intradiscal pressures. In the calibration, the sensor element exhibits a linear response to the applied pressure over the range of 0 - 70 kPa, with a sensitivity of 0.0206 μm/kPa and a resolution of 0.17 kPa.

Highly responsive screen-printed asymmetric pressure sensor based on laser-induced graphene

2021 ◽  
Author(s):  
Jiang Zhao ◽  
Jiahao Gui ◽  
Jinsong Luo ◽  
Jing Gao ◽  
Caidong Zheng ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
Screen Printing ◽  
Large Scale ◽  
Low Cost ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Wearable Electronics ◽  
Integrated Sensor ◽  
Patterned Electrodes ◽  
Screen Printed

Abstract Graphene-based pressure sensors have received extensive attention in wearable devices. However, reliable, low-cost, and large-scale preparation of structurally stable graphene electrodes for flexible pressure sensors is still a challenge. Herein, for the first time, laser-induced graphene (LIG) powder are prepared into screen printing ink, and shape-controllable LIG patterned electrodes can be obtained on various substrates using a facile screen printing process, and a novel asymmetric pressure sensor composed of the resulting screen-printed LIG electrodes has been developed. Benefit from the 3D porous structure of LIG, the as-prepared flexible LIG screen-printed asymmetric pressure sensor has super sensing properties with a high sensitivity of 1.86 kPa−1, low detection limit of about 3.4 Pa, short response time, and long cycle durability. Such excellent sensing performances give our flexible asymmetric LIG screen-printed pressure sensor the ability to realize real-time detection of tiny body physiological movements (such as wrist pulse and pronunciation action). Besides, the integrated sensor array has a multi-touch function. This work could stimulate an appropriate approach to designing shape-controllable LIG screen-printed patterned electrodes on various flexible substrates to adapt the specific needs of fulfilling compatibility and modular integration for potential application prospects in wearable electronics.

Modeling and Simulation of the Thermal Drift Characteristics of the Piezoresistive Pressure Sensor

2010 ◽  
Vol 2010 (HITEC) ◽  
pp. 000373-000378
Author(s):  
R. Otmani ◽  
N. Benmoussa ◽  
K. Ghaffour
Keyword(s):  
Thermal Behavior ◽  
Modeling And Simulation ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Thermal Drift ◽  
Piezoresistive Pressure Sensor ◽  
Output Characteristics ◽  
Piezoresistive Pressure Sensors

Piezoresistive pressure sensors based on Silicon have a large thermal drift because of their high sensitivity to temperature (ten times more sensitive to temperature than metals). So the study of the thermal behavior of these sensors is essential to define the parameters that cause the drift of the output characteristics. In this study, we adopted the behavior of 2nd degree gauges depending on the temperature. Then we model the thermal behavior of the sensor and its characteristics.

scholarly journals Nano Carbon Black-Based High Performance Wearable Pressure Sensors

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 664 ◽  
Author(s):  
Junsong Hu ◽  
Junsheng Yu ◽  
Ying Li ◽  
Xiaoqing Liao ◽  
Xingwu Yan ◽  
...  
Keyword(s):  
Carbon Black ◽  
Pressure Sensor ◽  
High Performance ◽  
Large Scale ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Wearable Electronics ◽  
Atmospheric Pollutant ◽  
Piezoresistive Pressure Sensor ◽  
Nano Carbon

The reasonable design pattern of flexible pressure sensors with excellent performance and prominent features including high sensitivity and a relatively wide workable linear range has attracted significant attention owing to their potential application in the advanced wearable electronics and artificial intelligence fields. Herein, nano carbon black from kerosene soot, an atmospheric pollutant generated during the insufficient burning of hydrocarbon fuels, was utilized as the conductive material with a bottom interdigitated textile electrode screen printed using silver paste to construct a piezoresistive pressure sensor with prominent performance. Owing to the distinct loose porous structure, the lumpy surface roughness of the fabric electrodes, and the softness of polydimethylsiloxane, the piezoresistive pressure sensor exhibited superior detection performance, including high sensitivity (31.63 kPa−1 within the range of 0–2 kPa), a relatively large feasible range (0–15 kPa), a low detection limit (2.26 pa), and a rapid response time (15 ms). Thus, these sensors act as outstanding candidates for detecting the human physiological signal and large-scale limb movement, showing their broad range of application prospects in the advanced wearable electronics field.

Sign in / Sign up

Export Citation Format

Share Document