scholarly journals Dose Dependence of Micro-Voids Distributions in Low-Temperature Neutron Irradiated Eurofer97 Steel

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 552 ◽  
Author(s):  
Roberto Coppola ◽  
Michael Klimenkov
Keyword(s):  
Electron Microscopy ◽  
Cross Sections ◽  
Damage Evolution ◽  
Small Angle Neutron Scattering ◽  
Transformation Method ◽  
Dose Dependence ◽  
Good Resistance ◽  
Mixed Spectrum ◽  
Microstructural Effects ◽  
Before And After

The microstructural effects of mixed spectrum neutron irradiation at 250 °C and 300 °C, for 2.7 dpa, 8.4 dpa, and 16.3 dpa doses, have been investigated in standard Eurofer97 (0.12 C, 9 Cr, 0.48 Mn, 0.2 V, 1.08 W, 0.14 Ta wt%) by means of small-angle neutron scattering (SANS) compared with un-irradiated Eurofer97. The observed SANS effects are attributed to the development of micro-voids, also detected by electron microscopy. The micro-voids distributions have been obtained by an improved transformation method of the SANS cross-sections providing consistent results both before and after subtraction of the un-irradiated reference. Mono-disperse micro-voids distributions are found, with average radii increasing with the dose, namely 4.4 Å for irradiation to 2.7 dpa at 300 °C, 6.6 Å for 8.4 dpa at 300 °C, and 12.9 Å for 16.4 dpa at 250 °C; the corresponding volume fractions are 0.001, 0.006, and 0.004, respectively. The differences in such distributions might reflect different damage evolution mechanisms for the different irradiation conditions, as also suggested by the comparison with a Eurofer97 sample irradiated under fast spectrum. A good resistance of Eurofer97 to micro-structural radiation damage, at least under these irradiation conditions, is suggested by the analysis of these experimental results.

Direct Observation of Heat Exchanger Deposits by Cross Sectioning

1967 ◽  
Vol 25 ◽  
pp. 364-365
Author(s):  
R. W. Anderson ◽  
D. L. Senecal
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Heat Exchanger ◽  
Direct Observation ◽  
Cross Sections ◽  
Preparation Method ◽  
Specimen Preparation ◽  
Flowing Water ◽  
Transmission Electron ◽  
Deposit Layer

A problem was presented to observe the packing densities of deposits of sub-micron corrosion product particles. The deposits were 5-100 mils thick and had formed on the inside surfaces of 3/8 inch diameter Zircaloy-2 heat exchanger tubes. The particles were iron oxides deposited from flowing water and consequently were only weakly bonded. Particular care was required during handling to preserve the original formations of the deposits. The specimen preparation method described below allowed direct observation of cross sections of the deposit layers by transmission electron microscopy.The specimens were short sections of the tubes (about 3 inches long) that were carefully cut from the systems. The insides of the tube sections were first coated with a thin layer of a fluid epoxy resin by dipping. This coating served to impregnate the deposit layer as well as to protect the layer if subsequent handling were required.

The Precipitation of Si in AlCuSi Thin Films

1973 ◽  
Vol 31 ◽  
pp. 34-35 ◽  
Author(s):  
R. M. Anderson
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Heat Treatment ◽  
Solid Solution ◽  
Integrated Circuit ◽  
Copper Film ◽  
Solution Concentration ◽  
X Ray ◽  
Silicon Thin Films ◽  
Before And After

Aluminum-copper-silicon thin films have been considered as an interconnection metallurgy for integrated circuit applications. Various schemes have been proposed to incorporate small percent-ages of silicon into films that typically contain two to five percent copper. We undertook a study of the total effect of silicon on the aluminum copper film as revealed by transmission electron microscopy, scanning electron microscopy, x-ray diffraction and ion microprobe techniques as a function of the various deposition methods.X-ray investigations noted a change in solid solution concentration as a function of Si content before and after heat-treatment. The amount of solid solution in the Al increased with heat-treatment for films with ≥2% silicon and decreased for films <2% silicon.

Complex Vesicles, Microtubules, and Cytoplasmic Filaments in the Endothelial Cells of Normal Dog Aorta

1968 ◽  
Vol 26 ◽  
pp. 172-173
Author(s):  
C. N. Sun ◽  
J. J. Ghidoni
Keyword(s):  
Electron Microscopy ◽  
Endothelial Cells ◽  
Cross Sections ◽  
Functional Significance ◽  
Tubular Structures ◽  
Aldehyde Fixation ◽  
Cytoplasmic Filaments

Endothelial cells in longitudinal and cross sections of aortas from 3 randomly selected “normal” mongrel dogs were studied by electron microscopy. Segments of aorta were distended with cold cacodylate buffered 5% glutaraldehyde for 10 minutes prior to being cut into small, well oriented tissue blocks. After an additional 1-1/2 hour period in glutaraldehyde, the tissue blocks were well rinsed in buffer and post-fixed in OsO4. After dehydration they were embedded in a mixture of Maraglas, D.E.R. 732, and DDSA.Aldehyde fixation preserves the filamentous and tubular structures (300 Å and less) for adequate demonstration and study. The functional significance of filaments and microtubules has been recently discussed by Buckley and Porter; the precise roles of these cytoplasmic components remains problematic. Endothelial cells in canine aortas contained an abundance of both types of structures.

The Response of Testis Cells to Low Dose X-Irradiation

1981 ◽  
Vol 39 ◽  
pp. 542-543
Author(s):  
D. E. Philpott ◽  
W. Sapp ◽  
C. Williams ◽  
Joann Stevenson ◽  
S. Black
Keyword(s):  
Electron Microscopy ◽  
Stem Cell ◽  
Light Microscopy ◽  
Dose Level ◽  
Cross Sections ◽  
Low Dose ◽  
Light And Electron Microscopy ◽  
Cellular Responses ◽  
Post Irradiation ◽  
X Irradiation

The response of spermatogonial cells to X-irradiation is well documented. It has been shown that there is a radiation resistent stem cell (As) which, after irradiation, replenishes the seminiferous epithelium. Most investigations in this area have dealt with radiation dosages of 100R or more. This study was undertaken to observe cellular responses at doses less than 100R of X-irradiation utilizing a system in which the tissue can be used for light and electron microscopy.Brown B6D2F1 mice aged 16 weeks were exposed to X-irradiation (225KeV; 15mA; filter 0.35 Cu; 50-60 R/min). Four mice were irradiated at each dose level between 1 and 100 rads. Testes were removed 3 days post-irradiation, fixed, and embedded. Sections were cut at 2 microns for light microscopy. After staining, surviving spermatogonia were identified and counted in tubule cross sections. The surviving fraction of spermatogonia compared to control, S/S0, was plotted against dose to give the curve shown in Fig. 1.

Absolute inner-shell cross section determination for EELS analysis

1988 ◽  
Vol 46 ◽  
pp. 534-535
Author(s):  
P.A. Crozier
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Absolute Cross Section ◽  
Specimen Thickness ◽  
Mass Thickness ◽  
Scattering Cross ◽  
Before And After ◽  
Estimated Error ◽  
Scattering Cross Sections ◽  
Electron Microscopist

Absolute inelastic scattering cross sections or mean free paths are often used in EELS analysis for determining elemental concentrations and specimen thickness. In most instances, theoretical values must be used because there have been few attempts to determine experimental scattering cross sections from solids under the conditions of interest to electron microscopist. In addition to providing data for spectral quantitation, absolute cross section measurements yields useful information on many of the approximations which are frequently involved in EELS analysis procedures. In this paper, experimental cross sections are presented for some inner-shell edges of Al, Cu, Ag and Au.Uniform thin films of the previously mentioned materials were prepared by vacuum evaporation onto microscope cover slips. The cover slips were weighed before and after evaporation to determine the mass thickness of the films. The estimated error in this method of determining mass thickness was ±7 x 107g/cm2. The films were floated off in water and mounted on Cu grids.

Low-temperature annealing of YBa2Cu3O7-x

1992 ◽  
Vol 50 (1) ◽  
pp. 88-89
Author(s):  
R.L. Sabatini ◽  
Yimei Zhu ◽  
Masaki Suenaga ◽  
A.R. Moodenbaugh
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Temperature ◽  
Oxygen Diffusion ◽  
Diffusion Rate ◽  
Oxygen Depletion ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Microstructural Effects ◽  
Oxygen Diffusion Rate

Low temperature annealing (<400°C) of YBa2Cu3O7x in a ozone containing oxygen atmosphere is sometimes carried out to oxygenate oxygen deficient thin films. Also, this technique can be used to fully oxygenate thinned TEM specimens when oxygen depletion in thin regions is suspected. However, the effects on the microstructure nor the extent of oxygenation of specimens has not been documented for specimens exposed to an ozone atmosphere. A particular concern is the fact that the ozone gas is so reactive and the oxygen diffusion rate at these temperatures is so slow that it may damage the specimen by an over-reaction. Thus we report here the results of an investigation on the microstructural effects of exposing a thinned YBa2Cu3O7-x specimen in an ozone atmosphere using transmission electron microscopy and energy loss spectroscopy techniques.

SEM analysis of fish scale cross sections: A technique study

1992 ◽  
Vol 50 (1) ◽  
pp. 744-745
Author(s):  
M.E. Lee ◽  
A. Moller ◽  
P.S.O. Fouche ◽  
I.G Gaigher
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Cross Sections ◽  
Soft Tissues ◽  
Close Association ◽  
Sem Analysis ◽  
Fish Scale ◽  
Fish Scales ◽  
Micro Structures ◽  
Scanning Electron

Scanning electron microscopy of fish scales has facilitated the application of micro-structures to systematics. Electron microscopy studies have added more information on the structure of the scale and the associated cells, many problems still remain unsolved, because of our incomplete knowledge of the process of calcification. One of the main purposes of these studies has been to study the histology, histochemistry, and ultrastructure of both calcified and decalcified scales, and associated cells, and to obtain more information on the mechanism of calcification in the scales. The study of a calcified scale with the electron microscope is complicated by the difficulty in sectioning this material because of the close association of very hard tissue with very soft tissues. Sections often shatter and blemishes are difficult to avoid. Therefore the aim of this study is firstly to develop techniques for the preparation of cross sections of fish scales for scanning electron microscopy and secondly the application of these techniques for the determination of the structures and calcification of fish scales.

Video Graphics and High-Voltage Electron Microscopy For Analysis of Microtubule Distributions In Fixed Cells

1990 ◽  
Vol 48 (1) ◽  
pp. 524-525
Author(s):  
Richard Mcintosh ◽  
David Mastronarde ◽  
Kent McDonald ◽  
Rubai Ding
Keyword(s):  
Electron Microscopy ◽  
Cross Sections ◽  
Cell Shape ◽  
Video Camera ◽  
Computer Memory ◽  
High Voltage Electron Microscopy ◽  
Thin Sections ◽  
Voltage Electron ◽  
Morphogenetic Event ◽  
Set Of Points

Microtubules (MTs) are cytoplasmic polymers whose dynamics have an influence on cell shape and motility. MTs influence cell behavior both through their growth and disassembly and through the binding of enzymes to their surfaces. In either case, the positions of the MTs change over time as cells grow and develop. We are working on methods to determine where MTs are at different times during either the cell cycle or a morphogenetic event, using thin and thick sections for electron microscopy and computer graphics to model MT distributions.One approach is to track MTs through serial thin sections cut transverse to the MT axis. This work uses a video camera to digitize electron micrographs of cross sections through a MT system and create image files in computer memory. These are aligned and corrected for relative distortions by using the positions of 8 - 10 MTs on adjacent sections to define a general linear transformation that will align and warp adjacent images to an optimum fit. Two hundred MT images are then used to calculate an “average MT”, and this is cross-correlated with each micrograph in the serial set to locate points likely to correspond to MT centers. This set of points is refined through a discriminate analysis that explores each cross correlogram in the neighborhood of every point with a high correlation score.

Scattering of Electrons at High - Pressure and Restoration of Image Contrast in High Pressure Scanning Electron Microscopy

1990 ◽  
Vol 48 (1) ◽  
pp. 384-385
Author(s):  
J. S. Shah ◽  
R. Durkin ◽  
A. N. Farley
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Pressure ◽  
Cross Sections ◽  
Single Scattering ◽  
Image Contrast ◽  
Experimental Scheme ◽  
Medium Resolution ◽  
Scattering Approximation ◽  
Scanning Electron

It is now possible to perform High Pressure Scanning Electron Microscopy (HPSEM) in the range 10 to 2000 Pa. Here the effect of scattering on resolution has been evaluated by calculating the profile of the beam in high pressure and assessing its effect on the image contrast . An experimental scheme is presented to show that the effect of the primary beam ionization is to reduce image contrast but this effect can be eliminated by a novel use of specimen current detection in the presence of an electric field. The mechanism of image enhancement is discussed in terms of collection of additional carriers generated by the emissive components.High Pressure SEM (HPSEM) instrumentation is establishing itself as commercially viable. There are now a number of manufacturers, such as JEOL, ABT, ESCAN, DEBEN RESEARCH, selling microscopes and accessories for HPSEM. This is because high pressure techniques have begun to yield high quality micrographs at medium resolution.To study the effect of scattering on the incident electron beam, its profile - in a high pressure environment - was evaluated by calculating the elastic and inelastic scattering cross sections for nitrogen in the energy range 5-25 keV. To assess the effect of the scattered beam on the image contrast, the modification of a sharp step contrast function due to scattering was calculated by single scattering approximation and experimentally confirmed for a 20kV accelerated beam.

Sign in / Sign up

Export Citation Format

Share Document