scholarly journals Amorphous Steel Coatings Deposited by Cold-Gas Spraying

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 678 ◽  
Author(s):  
Mario Tului ◽  
Cecilia Bartuli ◽  
Alessia Bezzon ◽  
Angelo Luigi Marino ◽  
Francesco Marra ◽  
...  
Keyword(s):  
Microstructural Characterization ◽  
Shear Instability ◽  
High Particle ◽  
Transmission Electron ◽  
Plastic Deformation Process ◽  
Heat Treated ◽  
Backscattered Electron ◽  
Higher Temperature ◽  
Amorphous Steel ◽  
Cold Gas

Cold-gas spray (CGS) deposition of amorphous steel coatings starting from a commercial feedstock powder containing boron, tungsten, and silicon was investigated. Microstructural characterization, carried out by X-ray diffraction (XRD), transmission electron microscopy, and backscattered electron diffraction (EBSD) analysis, confirmed the amorphous nature of deposited coatings. The amorphization phenomenon is related to high-strain/strain-rate deformation with shear instability caused by very high particle kinetic energy, with a mechanism that resembles the severe plastic deformation process. The CGS coatings were heat-treated at temperatures ranging from 650 to 850 °C to induce partial recrystallization. The effect of nanocrystal nucleation and growth on the hardness of the coatings was investigated, and the hardness of heat-treated samples was found to increase with respect to as-sprayed coatings, outperforming conventional high-velocity oxy-fuel (HVOF) deposits. Hardness was found to decrease after prolonged (<90 min) or higher temperature (>750 °C) exposures.

scholarly journals Effect of heat treatments on superconducting properties and connectivity in K-doped BaFe2As2

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Chiara Tarantini ◽  
Chongin Pak ◽  
Yi-Feng Su ◽  
Eric E. Hellstrom ◽  
David C. Larbalestier ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Specific Heat ◽  
High Purity ◽  
Heat Treatments ◽  
Treatment Temperature ◽  
Vortex Pinning ◽  
Distribution Analysis ◽  
Transmission Electron ◽  
Heat Treated ◽  
Higher Temperature

AbstractFe-based superconductors and in particular K-doped BaFe2As2 (K-Ba122) are materials of interest for possible future high-field applications. However the critical current density (Jc) in polycrystalline Ba122 is still quite low and connectivity issues are suspected to be responsible. In this work we investigated the properties of high-purity, carefully processed, K-Ba122 samples synthesized with two separate heat treatments at various temperatures between 600 and 825 °C. We performed specific heat characterization and Tc-distribution analysis up to 16 T and we compared them with magnetic Tc and Jc characterizations, and transmission-electron-microscopy (TEM) microstructures. We found no direct correlation between the magnetic Tc and Jc, whereas the specific heat Tc-distributions did provide valuable insights. In fact the best Jc-performing sample, heat treated first at 750 °C and then at 600 °C, has the peak of the Tc-distributions at the highest temperatures and the least field sensitivity, thus maximizing Hc2. We also observed that the magnetic Tc onset was always significantly lower than the specific heat Tc: although we partially ascribe the lower magnetization Tc to the small grain size (< λ, the penetration depth) of the K-Ba122 phase, this behaviour also implies the presence of some grain-boundary barriers to current flow. Comparing the Tc-distribution with Jc, our systematic synthesis study reveals that increasing the first heat treatment above 750 °C or the second one above 600 °C significantly compromises the connectivity and suppresses the vortex pinning properties. We conclude that high-purity precursors and clean processing are not yet enough to overcome all Jc limitations. However, our study suggests that a higher temperature Tc-distribution, a larger Hc2 and a better connectivity could be achieved by lowering the second heat treatment temperature below 600 °C thus enhancing, as a consequence, Jc.

Direct Observation of Crystalline Ordering In Naturally Graphitized Carbon Produced by Low Grade Metamorphism

1977 ◽  
Vol 35 ◽  
pp. 162-163
Author(s):  
Thomas R. McKee ◽  
Peter R. Buseck
Keyword(s):  
Crystallite Size ◽  
Sedimentary Rocks ◽  
Carbonaceous Material ◽  
Low Grade ◽  
X Ray ◽  
Graphitized Carbon ◽  
Transmission Electron ◽  
Heat Treated ◽  
Commercial Carbon ◽  
Metamorphic Zone

Sediments commonly contain organic material which appears as refractory carbonaceous material in metamorphosed sedimentary rocks. Grew and others have shown that relative carbon content, crystallite size, X-ray crystallinity and development of well-ordered graphite crystal structure of the carbonaceous material increases with increasing metamorphic grade. The graphitization process is irreversible and appears to be continous from the amorphous to the completely graphitized stage. The most dramatic chemical and crystallographic changes take place within the chlorite metamorphic zone.The detailed X-ray investigation of crystallite size and crystalline ordering is complex and can best be investigated by other means such as high resolution transmission electron microscopy (HRTEM). The natural graphitization series is similar to that for heat-treated commercial carbon blacks, which have been successfully studied by HRTEM (Ban and others).

Nucleation of Disorder in Fe3Al Alloys

1967 ◽  
Vol 25 ◽  
pp. 312-313
Author(s):  
P. R. Swann ◽  
W. R. Duff ◽  
R. M. Fisher
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Annealing Temperature ◽  
Antiphase Domain ◽  
Effect Of Temperature ◽  
Domain Structures ◽  
Transmission Electron ◽  
Domain Boundaries ◽  
Higher Temperature ◽  
The One

Recently we have investigated the phase equilibria and antiphase domain structures of Fe-Al alloys containing from 18 to 50 at.% Al by transmission electron microscopy and Mössbauer techniques. This study has revealed that none of the published phase diagrams are correct, although the one proposed by Rimlinger agrees most closely with our results to be published separately. In this paper observations by transmission electron microscopy relating to the nucleation of disorder in Fe-24% Al will be described. Figure 1 shows the structure after heating this alloy to 776.6°C and quenching. The white areas are B2 micro-domains corresponding to regions of disorder which form at the annealing temperature and re-order during the quench. By examining specimens heated in a temperature gradient of 2°C/cm it is possible to determine the effect of temperature on the disordering reaction very precisely. It was found that disorder begins at existing antiphase domain boundaries but that at a slightly higher temperature (1°C) it also occurs by homogeneous nucleation within the domains. A small (∼ .01°C) further increase in temperature caused these micro-domains to completely fill the specimen.

Development of 200 kV Scanning-Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 410-411
Author(s):  
H. Koike ◽  
S. Sakurai ◽  
K. Ueno ◽  
M. Watanabe
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Scanning Transmission Electron Microscope ◽  
The Other ◽  
Morphological Observation ◽  
Magnetic Domains ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Backscattered Electron ◽  
Increasing Demand

In recent years, there has been increasing demand for higher voltage SEMs, in the field of surface observation, especially that of magnetic domains, dislocations, and electron channeling patterns by backscattered electron microscopy. On the other hand, the resolution of the CTEM has now reached 1 ∼ 2Å, and several reports have recently been made on the observation of atom images, indicating that the ultimate goal of morphological observation has beem nearly achieved.

Thickness and composition determinations from T.E.M. specimens using both x-ray and backscattered electron data

1984 ◽  
Vol 42 ◽  
pp. 576-577
Author(s):  
M.D. Ball ◽  
H. Lagace ◽  
M.C. Thornton
Keyword(s):  
Electron Microscope ◽  
Atomic Number ◽  
Transmission Electron Microscope ◽  
Convenient Method ◽  
Flow Chart ◽  
X Ray ◽  
Intensity Measurements ◽  
Transmission Electron ◽  
Electron Intensity ◽  
Backscattered Electron

The backscattered electron coefficient η for transmission electron microscope specimens depends on both the atomic number Z and the thickness t. Hence for specimens of known atomic number, the thickness can be determined from backscattered electron coefficient measurements. This work describes a simple and convenient method of estimating the thickness and the corrected composition of areas of uncertain atomic number by combining x-ray microanalysis and backscattered electron intensity measurements.The method is best described in terms of the flow chart shown In Figure 1. Having selected a feature of interest, x-ray microanalysis data is recorded and used to estimate the composition. At this stage thickness corrections for absorption and fluorescence are not performed.

The effect of small additions of Cu on precipitation in Al-Mg-Si alloys

1990 ◽  
Vol 48 (2) ◽  
pp. 442-443
Author(s):  
M. Tamizifar ◽  
G. Cliff ◽  
R.W. Devenish ◽  
G.W. Lorimer
Keyword(s):  
Electron Microscopy ◽  
Analytical Electron Microscopy ◽  
Scanning Transmission Electron Microscope ◽  
Argon Atmosphere ◽  
Age Hardening ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Analytical Electron ◽  
Scanning Transmission

Small additions of copper, <1 wt%, have a pronounced effect on the ageing response of Al-Mg-Si alloys. The object of the present investigation was to study the effect of additions of copper up to 0.5 wt% on the ageing response of a series of Al-Mg-Si alloys and to use high resolution analytical electron microscopy to determine the composition of the age hardening precipitates.The composition of the alloys investigated is given in Table 1. The alloys were heat treated in an argon atmosphere for 30m, water quenched and immediately aged either at 180°C for 15 h or given a duplex treatment of 180°C for 15 h followed by 350°C for 2 h2. The double-ageing treatment was similar to that carried out by Dumolt et al. Analyses of the precipitation were carried out with a HB 501 Scanning Transmission Electron Microscope. X-ray peak integrals were converted into weight fractions using the ratio technique of Cliff and Lorimer.

Microstructural characterization of a cast RENi5-based alloy

1993 ◽  
Vol 51 ◽  
pp. 1176-1177
Author(s):  
G. M. Micha ◽  
L. Zhang
Keyword(s):  
Electron Microscopy ◽  
Rare Earth ◽  
Microstructural Characterization ◽  
Binary Compound ◽  
Nickel Metal ◽  
Cast Material ◽  
Nickel Metal Hydride ◽  
Transmission Electron ◽  
Cast Condition

RENi5 (RE: rare earth) based alloys have been extensively evaluated for use as an electrode material for nickel-metal hydride batteries. A variety of alloys have been developed from the prototype intermetallic compound LaNi5. The use of mischmetal as a source of rare earth combined with transition metal and Al substitutions for Ni has caused the evolution of the alloy from a binary compound to one containing eight or more elements. This study evaluated the microstructural features of a complex commercial RENi5 based alloy using scanning and transmission electron microscopy.The alloy was evaluated in the as-cast condition. Its chemistry in at. pct. determined by bulk techniques was 12.1 La, 3.2 Ce, 1.5 Pr, 4.9 Nd, 50.2 Ni, 10.4 Co, 5.3 Mn and 2.0 Al. The as-cast material was of low strength, very brittle and contained a multitude of internal cracks. TEM foils could only be prepared by first embedding pieces of the alloy in epoxy.

Carbon Film Deposition On Silicon Using Low Energy Ion Beams

1991 ◽  
Vol 223 ◽  
Author(s):  
Qin Fuguang ◽  
Yao Zhenyu ◽  
Ren Zhizhang ◽  
S.-T. Lee ◽  
I. Bello ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Ion Beam ◽  
Carbon Film ◽  
Carbon Films ◽  
Film Deposition ◽  
Ion Energy ◽  
Transmission Electron ◽  
Higher Temperature ◽  
Post Implantation ◽  
Beam Deposition

ABSTRACTDirect ion beam deposition of carbon films on silicon in the ion energy range of 15–500eV and temperature range of 25–800°C has been studied using mass selected C+ ions under ultrahigh vacuum. The films were characterized with X-ray photoelectron spectroscopy, Raman spectroscopy, and transmission electron microscopy and diffraction analysis. Films deposited at room temperature consist mainly of amorphous carbon. Deposition at a higher temperature, or post-implantation annealing leads to formation of microcrystalline graphite. A deposition temperature above 800°C favors the formation of microcrystalline graphite with a preferred orientation in the (0001) direction. No evidence of diamond formation was observed in these films.

scholarly journals Effect of Heat Treatment on the As-Cast Microstructure and Hardness of NiSi3B2 Alloy

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 539
Author(s):  
Gonçalo M. Gorito ◽  
Aida B. Moreira ◽  
Pedro Lacerda ◽  
Manuel F. Vieira ◽  
Laura M. M. Ribeiro
Keyword(s):  
Heat Treatment ◽  
Elevated Temperatures ◽  
Casting Process ◽  
X Ray Diffraction ◽  
Heat Treated ◽  
Energy Dispersive Microanalysis ◽  
Eutectic Constituent ◽  
Backscattered Electron ◽  
Corrosion And Oxidation ◽  
Cast Microstructure

Cast Ni-Si-B alloys have the potential for high-temperature applications because of their high resistance to wear, impact, corrosion, and oxidation at elevated temperatures due to an appropriate balance of hard phases and austenite that ensures a good compromise between toughness and hardness. In this work, NiSi3B2 specimens, fabricated by the lost-wax casting process, were investigated. Given the complex multiphase cast microstructure, a differential scanning calorimeter (DSC-TGA) analysis was employed to characterize the reactions that occur during solidification and the resulting phases were characterized using scanning electron microscopy (SEM), with energy-dispersive microanalysis (EDS) and backscattered electron (BSE) image and X-ray diffraction (XRD). Due to the presence of hard phases, machining of the Ni-Si-B components can pose additional difficulties. Therefore, the conditions of the solution heat treatment, which might lead to the homogenization of the microstructure, consequently improving its machinability, were also investigated. The results of the heat-treated samples indicated that the dissolution of the eutectic constituent is accompanied by a significant decrease in the hardness (approximately 17%). It is important to emphasize that the solution heat treatments carried out reduced the hardness without affecting the percentage of borides, which will allow improving the machinability without adversely affecting the alloy performance in service.

Effect of copper incorporation on phase transformation behavior of electroless nickel–phosphorous coating and its effect on the tribological behavior

2020 ◽  
pp. 146442072098160
Author(s):  
Abhijit Biswas ◽  
Suman Kalyan Das ◽  
Prasanta Sahoo
Keyword(s):  
Heat Treatment ◽  
Phase Transformation ◽  
Tribological Behavior ◽  
Electroless Nickel ◽  
Two Phase ◽  
Microstructural Changes ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Higher Temperature ◽  
Effect Of Copper

The microstructural changes of electroless Ni–P–Cu coating at various heat-treatment conditions are investigated to understand its implications on the tribological behavior of the coating. Coatings are heat-treated at temperatures ranging between 200°C and 800 °C and for 1–4 h duration. Ni–P–Cu coatings exhibit two-phase transformations in the temperature range of 350–450 °C and the resulting microstructural changes are found to significantly affect their thermal stability and tribological attributes. Hardness of the coating doubles when heat-treated at 452 °C, due to the formation of harder Ni3P phase and crystalline NiCu. Better friction and wear performance are also noted upon heat treatment of the coating at the phase transformation regime, particularly at 400 °C. Wear mechanism is characterized by a mixed adhesive cum abrasive wear phenomena. Heat treatment at higher temperature (600 °C and above) and longer duration (4 h) results in grain coarsening phenomenon, which negatively influences the hardness and tribological characteristics of the coating. Besides, diffusion of iron from the ferrous substrate as well as greater oxide formation are noticed when the coating is heat-treated at higher temperatures and for longer durations (4 h).

Sign in / Sign up

Export Citation Format

Share Document