scholarly journals Processing–Microstructure Relation of Deformed and Partitioned (D&P) Steels

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 695 ◽  
Author(s):  
Li Liu ◽  
Binbin He ◽  
Mingxin Huang
Keyword(s):  
Dislocation Density ◽  
Electron Backscatter Diffraction ◽  
Tensile Tests ◽  
Warm Rolling ◽  
High Yield ◽  
Uniaxial Tensile ◽  
X Ray Diffraction ◽  
Bake Hardening ◽  
X Ray ◽  
Backscatter Diffraction

An ultrastrong and ductile deformed and partitioned (D&P) steel developed by dislocation engineering has been reported recently. However, the microstructure evolution during the D&P processes has not yet been fully understood. The present paper aims to elucidate the process–microstructure relation in D&P process. Specifically, the evolution of phase fraction and microstructure during the corresponding D&P process are captured by means of X-ray diffraction (XRD) and electron backscatter diffraction (EBSD). Subsequently, the effect of partitioning temperature on dislocation density and mechanical properties of D&P steel is investigated with the assistance of uniaxial tensile tests and synchrotron X-ray diffraction. It is found that a heterogeneous microstructure is firstly realized by hot rolling. The warm rolling is crucial in introducing dislocations, while deformation-induced martensite is mainly formed during cold rolling. The dislocation density of the D&P steel gradually decreases with the increase of partitioning temperature, while the high yield strength is maintained owing to the bake hardening. The ductility is firstly enhanced while then deteriorated by increasing partitioning temperature due to the strong interaction between dislocation and interstitial atoms at higher partitioning temperatures.

Comparison of electron backscatter and X-ray diffraction techniques for measuring dislocation density in Zircaloy-2

2019 ◽  
Vol 52 (2) ◽  
pp. 415-427 ◽  
Author(s):  
T. Skippon ◽  
L. Balogh ◽  
M. R. Daymond
Keyword(s):  
Dislocation Density ◽  
Electron Backscatter Diffraction ◽  
Profile Analysis ◽  
Line Profile Analysis ◽  
X Ray Diffraction ◽  
Density Measurements ◽  
X Ray ◽  
Ebsd Data ◽  
Electron Backscatter ◽  
Backscatter Diffraction

Two methods for measuring dislocation density were applied to a series of plastically deformed tensile samples of Zircaloy-2. Samples subjected to plastic strains ranging from 4 to 17% along a variety of loading paths were characterized using both electron backscatter diffraction (EBSD) and synchrotron X-ray line profile analysis (LPA). It was found that the EBSD-based method gave results which were similar in magnitude to those obtained by LPA and followed a similar trend with increasing plastic strain. The effects of microscope parameters and post-processing of the EBSD data on dislocation density measurements are also discussed. The typical method for estimating uncertainty in dislocation density measured via EBSD was shown to be overly conservative, and a more realistic method of determining uncertainty is presented as an alternative.

scholarly journals Stable and Metastable Phase Equilibria Involving the Cu6Sn5 Intermetallic

2021 ◽  
Author(s):  
A. Leineweber ◽  
M. Löffler ◽  
S. Martin
Keyword(s):  
Phase Equilibria ◽  
Electron Backscatter Diffraction ◽  
Metastable Phase ◽  
Stable Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Ordered Phases ◽  
Backscatter Diffraction ◽  
Kinetics Of

Abstract Cu6Sn5 intermetallic occurs in the form of differently ordered phases η, η′ and η′′. In solder joints, this intermetallic can undergo changes in composition and the state of order without or while interacting with excess Cu and excess Sn in the system, potentially giving rise to detrimental changes in the mechanical properties of the solder. In order to study such processes in fundamental detail and to get more detailed information about the metastable and stable phase equilibria, model alloys consisting of Cu3Sn + Cu6Sn5 as well as Cu6Sn5 + Sn-rich melt were heat treated. Powder x-ray diffraction and scanning electron microscopy supplemented by electron backscatter diffraction were used to investigate the structural and microstructural changes. It was shown that Sn-poor η can increase its Sn content by Cu3Sn precipitation at grain boundaries or by uptake of Sn from the Sn-rich melt. From the kinetics of the former process at 513 K and the grain size of the η phase, we obtained an interdiffusion coefficient in η of (3 ± 1) × 10−16 m2 s−1. Comparison of this value with literature data implies that this value reflects pure volume (inter)diffusion, while Cu6Sn5 growth at low temperature is typically strongly influenced by grain-boundary diffusion. These investigations also confirm that η′′ forming below a composition-dependent transus temperature gradually enriches in Sn content, confirming that Sn-poor η′′ is metastable against decomposition into Cu3Sn and more Sn-rich η or (at lower temperatures) η′. Graphic Abstract

Mitrofanovite, Pt3Te4, a new mineral from the East Chuarvy deposit, Fedorovo–Pana intrusion, Kola Peninsula, Russia

2018 ◽  
Vol 83 (4) ◽  
pp. 523-530 ◽  
Author(s):  
Victor V. Subbotin ◽  
Anna Vymazalová ◽  
František Laufek ◽  
Yevgeny E. Savchenko ◽  
Chris J. Stanley ◽  
...  
Keyword(s):  
Kola Peninsula ◽  
Electron Backscatter Diffraction ◽  
New Mineral ◽  
Synthetic Analogue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structural Identity ◽  
Polarised Light ◽  
Fe Alloys ◽  
Backscatter Diffraction

AbstractMitrofanovite, Pt3Te4, is a new telluride discovered in low-sulfide disseminated ore in the East Chuarvy deposit, Fedorovo–Pana intrusion, Kola Peninsula, Russia. It forms anhedral grains (up to ~20 μm × 50 μm) commonly in intergrowths with moncheite in aggregates with lukkulaisvaaraite, kotulskite, vysotskite, braggite, keithconnite, rustenburgite and Pt–Fe alloys hosted by a chalcopyrite–pentlandite–pyrrhotite matrix. Associated silicates are: orthopyroxene, augite, olivine, amphiboles and plagioclase. Mitrofanovite is brittle; it has a metallic lustre and a grey streak. Mitrofanovite has a good cleavage, along {001}. In plane-polarised light, mitrofanovite is bright white with medium to strong bireflectance, slight pleochroism, and strong anisotropy on non-basal sections with greyish brown rotation tints; it exhibits no internal reflections. Reflectance values for the synthetic analogue of mitrofanovite in air (Ro, Re’ in %) are: 58.4, 54.6 at 470 nm; 62.7, 58.0 at 546 nm; 63.4, 59.1 at 589 nm; and 63.6, 59.5 at 650 nm. Fifteen electron-microprobe analyses of mitrofanovite gave an average composition: Pt 52.08, Pd 0.19, Te 47.08 and Bi 0.91, total 100.27 wt.%, corresponding to the formula (Pt2.91Pd0.02)Σ2.93(Te4.02Bi0.05)Σ4.07 based on 7 atoms; the average of eleven analyses on synthetic analogue is: Pt 52.57 and Te 47.45, total 100.02 wt.%, corresponding to Pt2.94Te4.06. The density, calculated on the basis of the formula, is 11.18 g/cm3. The mineral is trigonal, space group R$\overline 3 $m, with a = 3.9874(1), c = 35.361(1) Å, V = 486.91(2) Å3 and Z = 3. The crystal structure was solved and refined from the powder X-ray-diffraction data of synthetic Pt3Te4. Mitrofanovite is structurally and chemically related to moncheite (PtTe2). The strongest lines in the powder X-ray diffraction pattern of synthetic mitrofanovite [d in Å (I) (hkl)] are: 11.790(23)(003), 5.891(100)(006), 2.851(26)(107), 2.137(16)(1013), 2.039(18)(0114), 1.574(24)(0120), 1.3098(21)(0027). The structural identity of natural mitrofanovite with synthetic Pt3Te4 was confirmed by electron backscatter diffraction measurements on the natural sample. The mineral name is chosen to honour Felix P. Mitrofanov, a Russian geologist who was among the first to discover platinum-group element mineralisation in the Fedorova–Pana complex.

Temperature-Dependent Mechanical Stability of Retained Austenite in Thermomechanically Processed 3Mn Steel

2021 ◽  
Vol 1016 ◽  
pp. 762-767
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański
Keyword(s):  
Retained Austenite ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Tensile Tests ◽  
Trip Effect ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
Static Tensile ◽  
The Stability ◽  
Backscatter Diffraction

The temperature-dependent mechanical stability of retained austenite in medium-Mn transformation induced plasticity 0.17C-3.3Mn-1.6Al-1.7Al-0.22Si-0.23Mo thermomechanically processed steel was investigated using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and X-ray diffraction (XRD) methods. Specimens were deformed up to rupture in static tensile tests in a temperature range 20–200°C. It was found that deformation temperature affects significantly the intensity of TRIP effect. In case of specimens deformed at temperatures higher than 60°C, a gradual temperature-related decrease in the stability of γ phase was noted. It indicates a progressive decrease of the significance of the TRIP effect and at the same time the growing importance of the thermally activated processes affecting a thermal stability of retained austenite.

Deformation Structures in a Duplex Stainless Steel

2018 ◽  
Vol 941 ◽  
pp. 176-181 ◽  
Author(s):  
Karin Yvell ◽  
Göran Engberg
Keyword(s):  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
True Strain ◽  
Strain Curve ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Deformation Structure ◽  
Pole Figures ◽  
Two Phases ◽  
Backscatter Diffraction

The evolution of the deformation structure with strain has been studied using electron backscatter diffraction (EBSD). Samples from interrupted uniaxial tensile tests and from a cyclic tension/compression test were investigated. The evolution of low angle boundaries (LABs) was studied using boundary maps and by measuring the LAB density. From calculations of local misorientations, smaller orientation changes in the substructure can be illustrated. The different orientations developed with strain within a grain, due to operation of different slip systems in different parts of the grain, were studied using a misorientation profile showing substantial orientation changes after a true strain of 0.24. The texture evolution with increasing strain was followed by using inverse pole figures (IPFs). The observed substructure development in the ferritic and austenitic phases could be successfully correlated with the stress-strain curve from a tensile test. LABs were first observed in the different phases when the strain hardening rate changed in appearance indicating that cross slip started to operate as a significant dislocation recovery mechanism. The evolution of the deformation structure is concluded to occur in a similar manner in the austenitic and ferritic phases but with different texture evolution for the two phases.

scholarly journals Effects of Annealing Temperature on Recrystallization Texture and Microstructure Uniformity of High Purity Tantalum

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 75 ◽  
Author(s):  
Jialin Zhu ◽  
Chao Deng ◽  
Yahui Liu ◽  
Nan Lin ◽  
Shifeng Liu
Keyword(s):  
Low Temperature ◽  
Electron Backscatter Diffraction ◽  
Stored Energy ◽  
X Ray Diffraction ◽  
Center Layer ◽  
X Ray ◽  
Texture Intensity ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Backscatter Diffraction

One hundred and thirty-five degree clock rolling significantly improves the texture homogeneity of tantalum sheets along the thickness, but a distinctly fragmented substructure is formed within {111} (<111>//normal direction (ND)) and {100} (<100>//ND) deformation grains, which is not suitable to obtain a uniform recrystallization microstructure. Thus, effects of different annealing temperatures on the microstructure and texture heterogeneity of tantalum sheets along the thickness were investigated by X-ray diffraction (XRD), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Results show that the texture distribution along θ-fiber and γ-fiber is irregular and many large grains with {111} orientation develop during annealing at high temperature. However, low-temperature annealing can not only weaken the texture intensity in the surface and the center layer but also introduce a more uniform grain size distribution. This result can be attributed to the subgrain-nucleation-dominated recrystallization mechanism induced by recovery at low temperature, and moreover, a considerable decline of recrystallization driving force resulting from the release of stored energy in the deformation matrix.

scholarly journals Effect of TiO2-Nanoparticles on Ni Electrodeposition on Copper Wire

Metals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 406
Author(s):  
Samiha Saad ◽  
Zakaria Boumerzoug ◽  
Anne Laure Helbert ◽  
François Brisset ◽  
Thierry Baudin
Keyword(s):  
Surface Morphology ◽  
Tio2 Nanoparticles ◽  
Vickers Microhardness ◽  
Electron Backscatter Diffraction ◽  
Copper Wire ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electron Backscatter ◽  
Electrodeposited Nickel ◽  
Backscatter Diffraction

The objective of this work is to study, on a copper wire, the effect of TiO2-nanoparticles on electrodeposited nickel. Both the microstructure and surface morphology (texture) of the coating were investigated. This deposit is obtained from baths of sulfated electroplating Watts. The Ni-TO2 composite coating is deposited at a temperature of 45 °C. The composite deposit is prepared by adding nanoparticles of TiO2 to the electrolyte. The characterization has been carried out by X-ray diffraction, scanning electron microscopy, microhardness measurements, and electron backscatter diffraction (EBSD). Vickers microhardness was used to characterize the mechanical properties of the electrodeposited nickel. The results showed the effects of the TiO2 on the composition, the surface morphology, and the hardness of the deposited layer. However, there was not an effect of TiO2 nanoparticles on texture.

X-ray diffraction contrast tomography: a novel technique for three-dimensional grain mapping of polycrystals. II. The combined case

2008 ◽  
Vol 41 (2) ◽  
pp. 310-318 ◽  
Author(s):  
Greg Johnson ◽  
Andrew King ◽  
Marcelo Goncalves Honnicke ◽  
J. Marrow ◽  
Wolfgang Ludwig
Keyword(s):  
Electron Backscatter Diffraction ◽  
Three Dimensional ◽  
Real Data ◽  
X Ray Diffraction ◽  
Data Set ◽  
Transmitted Beam ◽  
X Ray ◽  
Diffraction Contrast ◽  
Simultaneous Acquisition ◽  
Backscatter Diffraction

By simultaneous acquisition of the transmitted and the diffracted beams, the applicability of the previously introduced diffraction contrast tomography technique [Ludwig, Schmidt, Lauridsen & Poulsen (2008).J. Appl. Cryst.41, 302–309] can be extended to the case of undeformed polycrystalline samples containing more than 100 grains per cross section. The grains are still imaged using the occasionally occurring diffraction contribution to the X-ray attenuation coefficient, which can be observed as a reduction in the intensity of the transmitted beam when a grain fulfils the diffraction condition. Automating the segmentation of the extinction spot images is possible with the additional diffracted beam information, even in the presence of significant spot overlap. By pairing the corresponding direct (`extinction') and diffracted beam spots a robust sorting and indexing approach has been implemented. The analysis procedure is illustrated on a real data set and the result is validated by comparison with a two-dimensional grain map obtained by electron backscatter diffraction.

Sign in / Sign up

Export Citation Format

Share Document