scholarly journals Chitosan/Phosphate Rock-Derived Natural Polymeric Composite to Sequester Divalent Copper Ions from Water

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 2028
Author(s):  
Rachid El Kaim Billah ◽  
Moonis Ali Khan ◽  
Saikh Mohammad Wabaidur ◽  
Byong-Hun Jeon ◽  
Amira AM ◽  
...  
Keyword(s):  
Phosphate Rock ◽  
Copper Ions ◽  
Polymeric Composite ◽  
Ternary Systems ◽  
Order Kinetic ◽  
Divalent Copper ◽  
Significant Drop ◽  
Bet Analysis ◽  
Adsorption Data ◽  
Order Kinetic Model

Herein, a chitosan (CH) and fluroapatite (TNP) based CH-TNP composite was synthesized by utilizing seafood waste and phosphate rock and was tested for divalent copper (Cu(II)) adsorptive removal from water. The XRD and FT-IR data affirmed the formation of a CH-TNP composite, while BET analysis showed that the surface area of the CH-TNP composite (35.5 m2/g) was twice that of CH (16.7 m2/g). Mechanistically, electrostatic, van der Waals, and co-ordinate interactions were primarily responsible for the binding of Cu(II) with the CH-TNP composite. The maximum Cu(II) uptake of both CH and CH-TNP composite was recorded in the pH range 3–4. Monolayer Cu(II) coverage over both CH and CH-TNP surfaces was confirmed by the fitting of adsorption data to a Langmuir isotherm model. The chemical nature of the adsorption process was confirmed by the fitting of a pseudo-second-order kinetic model to adsorption data. About 82% of Cu(II) from saturated CH-TNP was recovered by 0.5 M NaOH. A significant drop in Cu(II) uptake was observed after four consecutive regeneration cycles. The co-existing ions (in binary and ternary systems) significantly reduced the Cu(II) removal efficacy of CH-TNP.

REMOVAL OF STRONTIUM (II) FROM AQUEOUS SOLUTION USING FUNCTIONALIZED CARBON NANOTUBES

2012 ◽  
Vol 11 (02) ◽  
pp. 1250019 ◽  
Author(s):  
RAJESH KUMAR ◽  
S. K. JAIN
Keyword(s):  
Carbon Nanotubes ◽  
Polluted Water ◽  
Order Kinetic ◽  
Environmental Application ◽  
Functionalized Carbon Nanotubes ◽  
Multi Wall Carbon Nanotubes ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir

This study was carried out to evaluate the environmental application of functionalized carbon nanotubes through the experimental removal of strontium (II) from water. The aim was to find the optimal condition for the removal of strontium from water under different conditions such as initial concentration of strontium, contact time and neutral pH. The functionalized multi wall carbon nanotubes (f-MWCNT) were characterized by FT-IR and scanning electron microscopy (SEM). The adsorption isotherms were correlated to Freundlich and Langmuir models and it was found that the adsorption data could be fitted better by Langmuir model than Freundlich one. The kinetic data shows that the adsorption describes well with the pseudo-second order kinetic model. Functionalized MWCNT can be used as good adsorbent for the removal of the strontium ions from polluted water according to results.

scholarly journals Karekterisasi, Kinetika, dan Isoterm Adsorpsi Limbah Ampas Kelapa sebagai Adsorben Ion Cu(II)

SAINTIFIK ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 104-115
Author(s):  
Agusriyadin Agusriyadin
Keyword(s):  
Adsorption Capacity ◽  
Ph Effect ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Langmuir Adsorption ◽  
Adsorbent Surface ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Penelitian ini bertujuan untuk menguji kemampuan AK dan AKPM dalam mengadsorpsi ion Cu (II), pengaruh parameter adsorpsi dan mekanisme adsorpsi. AK dan AKP Madsorben dibuat dari residu ampas kelapa. Adsorben dikarakterisasi dengan FTIR, SEM dan EDS. Pengaruh parameter adsorpsi seperti pH awal, dosis adsorben, waktu kontak dan konsentrasi ion Cu (II) awal diperiksa untuk menentukan kondisi optimum serapan tembaga (II). Ion Cu (II) yang teradsorpsi diukur berdasarkan pada konsentrasi Ion Cu (II) sebelum dan sesudah adsorpsi menggunakan metode AAS. Hasil karakterisasi menunjukkan bahwa struktur pori dan gugus fungsi tersedia pada permukaan adsorben. Menurut percobaan efek pH, kapasitas adsorpsi maksimum dicapai pada pH 7. Waktu kontak optimal dan konsentrasi tembaga awal (II) ditemukan masing-masing pada 120 menit dan 100 mg L-1. Data eksperimental sesuai dengan model kinetik orde dua orde dua, dan Langmuir isoterm adsorpsi yang diperoleh paling sesuai dengan data adsorpsi. Kapasitas adsorpsi maksimum adsorben ditemukan menjadi 4,73 dan 6,46 mg g-1 pada kondisi optimal. The results of characterization showed that the pore structure and the functional groups were available on adsorbent surface. According to the pH effect experiments, the maximum adsorption capacity was achieved at pH 7. Optimum contact time and initial copper(II) concentration were found at 120 min and 100 mg L-1, respectively. The experimental data were comply with the pseudo-second-order kinetic model, and Langmuir adsorption isotherm obtained best fitted the adsorption data. The maximum adsorption capacity of the adsorbents was found to be 4.73 and 6.46 mg g-1 at optimum conditions.

scholarly journals Preparation of bio-absorbents by modifying licorice residue via chemical methods and removal of copper ions from wastewater

2021 ◽  
Author(s):  
Xiaochun Yin ◽  
Nadi Zhang ◽  
Meixia Du ◽  
Hai Zhu ◽  
Ting Ke
Keyword(s):  
Adsorption Capacity ◽  
Copper Ions ◽  
Order Kinetic ◽  
Solution Ph ◽  
Chemical Methods ◽  
Simple Strategy ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Surface Active ◽  
Adsorption Desorption

Abstract In this paper, a series of bio-adsorbents (LR-NaOH, LR-Na2CO3 and LR-CA) were successfully prepared by modifying Licorice Residue with NaOH, Na2CO3 and citric acid, which were used as the adsorbents to remove Cu2+ from wastewater. The morphology and structure of bio-adsorbents were characterized by Fourier Transform Infrared, SEM, TG and XRD. Using static adsorption experiments, the effects of the adsorbent dosage, the solution pH, the adsorption time, and the initial Cu2+ concentration on the adsorption performance of the adsorbents were investigated. The results showed that the adsorption process of Cu2+ by the bio-adsorbents can be described by pseudo-second order kinetic model and the Langmuir model. The surface structure of the LR-NaOH, LR-Na2CO3 and LR-CA changed obviously, and the surface-active groups increased. The adsorption capacity of raw LR was 21.56 mg/g, LR-NaOH, LR- Na2CO3 significantly enhanced this value up to 43.65 mg/g, 43.55 mg/g, respectively. After four adsorption-desorption processes, the adsorption capacity of LR-NaOH also maintained about 73%. Therefore, LR-NaOH would be a promising adsorbent for removing Cu2+ from wastewater, and the simple strategy towards preparation of adsorbent from the waste residue can be as a potential approach using in the water treatment.

scholarly journals Decolourization of malachite green dye by mentha plant biochar (MPB): a combined action of adsorption and electrochemical reduction processes

2018 ◽  
Vol 77 (6) ◽  
pp. 1734-1743 ◽  
Author(s):  
Abhay Prakash Rawat ◽  
D. P. Singh
Keyword(s):  
Malachite Green ◽  
Electron Transfer Reaction ◽  
Order Kinetic ◽  
Voltammetric Analysis ◽  
Malachite Green Dye ◽  
Type Iv ◽  
Bet Analysis ◽  
Order Kinetic Model ◽  
Combined Action ◽  
Adsorption Desorption

Abstract Adsorption behavior of mentha (mint) plant biochar (MPB) in removal of malachite green (MG) dye from aqueous solution was analyzed as a function of different pH (4.0–10.0), initial dye concentration (20–100 mg/L), contact time (0–45 min) and dose of adsorbent (0.05–0.3 g/100 mL). The zeta potential of the MPB particles was found to be −37.9 mV, indicating a negatively charged sorption surface of MPB particles. MPB was found to be more effective in removal of MG dye at pH 6.0 due to combined action of physico-chemisorption and a reductive electron transfer reaction. Results on the Brunauer–Emmett–Teller (BET) analysis of the N2 adsorption–desorption isotherm of MPB as adsorbent showed sigmoidal shape similar to the type IV isotherm and mesoporous nature. The cyclic voltammetric analysis of MG dye showed a reversible, coupled redox reaction at the interface of dye molecules and MPB particles. The maximum monolayer adsorption capacity (qmax) of MPB was found to be 322.58 mg g−1. The separation factor (RL) value was between 0 and 1, indicating a favourable adsorption of MG dye onto MPB. The results fitted well to a pseudo-second-order kinetic model. Further results from desorption experiments showed recovery of MG dye by about 50% in the presence of 1 N HCl.

scholarly journals The Presence of Cu Facilitates Adsorption of Tetracycline (TC) onto Water Hyacinth Roots

2018 ◽  
Vol 15 (9) ◽  
pp. 1982 ◽  
Author(s):  
Xin Lu ◽  
Beibei Tang ◽  
Qi Zhang ◽  
Lizhu Liu ◽  
Ruqin Fan ◽  
...  
Keyword(s):  
Water Hyacinth ◽  
Freundlich Isotherm ◽  
Root Surface ◽  
Interactive Effects ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ph Range

Batch experiments were conducted to investigate the adsorption characteristics of tetracycline (TC), and the interactive effects of copper (Cu) on the adsorption of TC onto water hyacinth roots. TC removal efficiency by water hyacinth roots was ranging from 58.9% to 84.6%, for virgin TC, 1:1 TC-Cu and 1:2 TC-Cu. The Freundlich isotherm model and the pseudo-second-order kinetic model fitted the adsorption data well. Thermodynamics parameters ΔG0 for TC were more negative in the TC plus Cu than the TC-only treatments, indicating the spontaneity of TC adsorption increased with increasing of Cu concentrations. An elevated temperature was associated with increasing adsorption of TC by water hyacinth roots. The additions of Cu(II) significantly increased TC adsorption onto water hyacinth roots within the pH range 4 to 6, because copper formed a strong metal bridge between root surface and TC molecule, facilitating the adsorption of TC by roots. However, Cu(II) hindered TC adsorption onto water hyacinth roots on the whole at pH range from 6–10, since the stronger electrostatic repulsion and formation of CuOH+ and Cu(OH)2. Therefore, the interaction between Cu(II) and TC under different environmental conditions should be taken into account to understand the environmental behavior, fate, and ecotoxicity of TC.

Adsorption Removal of Copper and Nickel Ions from Wastewater by Ammonia Modified Cotton Stalks

2014 ◽  
Vol 955-959 ◽  
pp. 2440-2443 ◽  
Author(s):  
Jing Li ◽  
Dong Mei Jia ◽  
Chang Hai Li ◽  
Bao Qing Yu
Keyword(s):  
Copper Ions ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Nickel Ions ◽  
Adsorption Removal ◽  
Cotton Stalks ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Adsorbent Dose

The ammonia modified cotton stalks (CS) were utilized to adsorb the Ni2+and Cu2+ions from wastewaters, and the effect parameters (i.e. pH, contact time, adsorbent dose, and temperature) were also investigated by batch adsorption experiments. The maximum uptake was attained, i.e., 99.4% and 98.8%, respectively, for nickel and copper ions, under the optimum conditions (adsorbent dose: 10 g/L; pH: 6.0 (Ni2+), 5.0 (Cu2+); t: 75min; T: 20 °C) when the initial concentration of heavy metal ions was 20 mg/L. The adsorption process of nickel and copper ions on ammonia modified CS was well described by the pseudo-second-order kinetic model.

scholarly journals Pine cones powder for the adsorptive removal of copper ions from water

2021 ◽  
pp. 1-1
Author(s):  
Redouane Ouafi ◽  
Anass Omor ◽  
Younes Gaga ◽  
Mohamed Akhazzane ◽  
Mustapha Taleb ◽  
...  
Keyword(s):  
Particle Size ◽  
Copper Ions ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Order Kinetic Model ◽  
Endothermic Process ◽  
Environmentally Friendly Process ◽  
Pine Cones

This research investigates the adsorption potential of pine cones powder (PCP) for the removal of copper ions (Cu(II)) from aqueous solutions. The process of adsorption was reasonably fast to be completed within a time of 60 min. The pseudo-second order kinetic model describes properly the Cu(II) adsorption by PCP. The adsorbent was characterised by various instrumental techniques and batch experiments were conducted to investigate the effect of PCP dose, solution pH, particle size and initial Cu(II) concentration on adsorption efficiency. Optimum Cu(II) removal occurred at a slightly acidic pH, with a particle size less than 100 ?m. The effective PCP dose was estimated to be 36 g.L-1. The increase in the initial concentration of Cu (II) was accompanied by a reduction in the rate of its reduction by almost half. The Langmuir model was the best fitting isotherm with a maximum adsorption capacity of 9.08 mg.g-1. The thermodynamic parameters values showed that the Cu(II) adsorption was a spontaneous and endothermic process. The results of this research suggest that Cu(II) could be removed through an environmentally friendly process using PCP as low-cost natural wastes.

Adsorption of Cu(II), Ni(II) and Zn(II) ions by nano kaolinite: Thermodynamics and kinetics studies

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Adsorption Process ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

An easy route for preparation emulsion of kaolinite (Al2Si2O5.4H2O) from Sweileh sand deposits, west Amman, Jordan by hydrochloric acid under continuous stirring for 4 h at room temperature was performed and nano kaolinite powder was used as an adsorbent for the removal of Cu(II), Zn(II) and Ni(II) ions. Nano kaolinite was characterized by XRD, FT-IR and SEM techniques. Effect of pH, adsorbent dose, initial metal ion concentration, contact time and temperature on adsorption process was examined. The negative values of ΔGo and the positive value of ΔHo revealed that the adsorption process was spontaneous and endothermic. The Langmuir isotherm model fitted well to metal ions adsorption data and the adsorption capacity. The kinetic data provided the best correlation of the adsorption with pseudo-second order kinetic model. In view of promising efficiency, the nano kaolinite can be employed for heavy metal ions adsorption.

scholarly journals Removal of Cu(II) Ions byLeucaena Leucocephala(Subabul) Seed Pods from Aqueous Solutions

2010 ◽  
Vol 7 (s1) ◽  
pp. S377-S385 ◽  
Author(s):  
A. K. Patil ◽  
V. S. Shrivastava
Keyword(s):  
Leucaena Leucocephala ◽  
Contact Time ◽  
Unit Weight ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Isotherm Equations ◽  
Adsorbent Dose

In this method,Leucaena leucocephalaseed pods (LLSP) have been used for removal of Cu(II) ions from aqueous solution. Batch adsorption experiments were conducted to study the effect of process parameters like pH, contact time initial Cu(II) ions concentration and adsorbent dose. The maximum adsorption of Cu(II) ions onLeucaena leucocephalaseed pods was 94.17% at pH 5. The amount of metal adsorbed per unit weight of adsorbent increases with time and reach equilibrium after 30 minutes of shaking time for the different initial metal concentrations. The Freundlich and Langmuir isotherm equations were applied for the equilibrium adsorption data and the various isotherm parameters were evaluated. The obtained plots were linear as evident fromR2values close to unity. The data agreed very well with the pseudo second-order kinetic model.

scholarly journals Cationic and Anionic Dye Adsorption on a Natural Clayey Composite

2021 ◽  
Vol 11 (11) ◽  
pp. 5127
Author(s):  
Carmen Omaira Márquez ◽  
Víctor Julio García ◽  
Jefferson Raúl Guaypatin ◽  
Francisco Fernández-Martínez ◽  
Anita Cecilia Ríos
Keyword(s):  
Dye Adsorption ◽  
Industrial Effluents ◽  
Order Kinetic ◽  
Red Clay ◽  
Adsorption Mechanisms ◽  
Anionic Dye ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Model Fits

One of the main challenges for environmental sciences today is the effective treatment of dye-laden industrial effluents. This work aimed to study the potential of an untreated (natural occurring clayey composite) red clay (RC) for the adsorption of a cationic dye Basic Navy Blue 2RN (CNB) and anionic dye Drimaren Yellow CL-2R (ADY). We evaluated the effect of pH, dye concentration, and adsorbent concentration on the removal effectiveness to study the absorption process. Also, we studied the adsorption process by analyzing the feasibility of several known adsorption isotherms and kinetic models. The results show that at a pH of less than 4, the CNB and ADY removal percentages were 97% and 96%, respectively. At a pH greater than 8, the CNB and ADY removals were 75% and 25%, respectively. The CNB adsorption happened by chemisorption of a monolayer on iron-containing particles (IPs). In congtrast, the ADY adsorption occurred by monolayer physisorption on kaolinite particles (KPs) and Na, K-rich Laumontite particles (LPs). The Langmuir isotherm model fits very well with CNB experimental data. The Temkin model shows the best fit between the isotherm function and the ADY dye-adsorption data. The pseudo-second-order kinetic model fits the CNB and ADY dye-adsorption data on RC particles. The heterogeneous composition of naturally occurring clay favors different adsorption mechanisms and opens an avenue for the separation process’s engineering.

Sign in / Sign up

Export Citation Format

Share Document