scholarly journals Performance Evaluation of Styrene-Butadiene-Styrene-Modified Stone Mastic Asphalt with Basalt Fiber Using Different Compaction Methods

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 1006 ◽  
Author(s):  
Wensheng Wang ◽  
Yongchun Cheng ◽  
Peilei Zhou ◽  
Guojin Tan ◽  
Haitao Wang ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Asphalt Binder ◽  
Basalt Fiber ◽  
Pavement Performance ◽  
Volumetric Properties ◽  
Mastic Asphalt ◽  
Stone Mastic Asphalt ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Butadiene Styrene

Superpave gyratory compaction (SGC) and Marshall compaction methods are essentially designed according to volumetric properties. In spite of the similarity, the optimum asphalt contents (OAC) of the two methods are greatly affected by the laboratory compaction process, which would further influence their performance. This study aims to evaluate the performance of styrene-butadiene-styrene (SBS)-modified stone mastic asphalt (SMA) with basalt fiber by using SGC and Marshall compaction methods. Basalt fiber was proved to improve and strength the basic properties of SBS-asphalt according to test results of asphalt binder. The effects of SGC and Marshall compaction methods on OAC and volumetric properties, i.e., density, air voids (VA), voids in mineral aggregates (VMA), and voids filled with asphalt (VFA), were evaluated in detail. Finally, the pavement performance of asphalt mixture prepared by SGC and Marshall compaction methods were compared in order to analyze the high-temperature creep, low-temperature splitting, and moisture stability performance. Results showed that the OAC of SGC (~5.70%) was slightly lower than that of Marshall method (5.80%). Furthermore, the pavement performance of SGC specimens were improved to a certain extent compared with Marshall specimens, indicating that SGC has a better compaction effect and mechanical performance.

Compatibility and Storage Stability of Asphalt Binder Modified by Styrene-Butadiene-Styrene (SBS) Graft Copolymer

2021 ◽  
Vol 1036 ◽  
pp. 459-470
Author(s):  
Hong Gang Zhang ◽  
Qiang Huai Zhang ◽  
Xue Ting Wang ◽  
Hua Tan ◽  
Li Ning Gao ◽  
...  
Keyword(s):  
Triblock Copolymer ◽  
Storage Stability ◽  
Asphalt Binder ◽  
Solubility Parameters ◽  
Suitable Alternative ◽  
Modified Asphalt ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Sbs Modified Asphalt ◽  
Butadiene Styrene

A styrene-butadiene-styrene triblock copolymer (SBS) was grafted with an unsaturated polar monomer (monomer A) composed of maleic anhydride (MAH) and methoxy polyethylene (MPEG) via a ring-opening reaction after epoxidizing styrene-butadiene-styrene triblock copolymer (ESBS). The microscopic changes of SBS before and after grafting has been characterized with Fourier transform infrared spectrum (FT-IR), X-ray photoelectron spectroscopy (XPS) and gel permeation chromatography (GPC). The results revealed that the monomer A was successfully grafted on SBS backbone, and the maximum graft ratio (GR) was 20.32%. To verify the compatibility between SBS and asphalt, solubility parameters and surface free energy (SFE) of SBS, grafted SBS and asphalt were measured. It was found that the solubility parameter and SFE of grafted SBS were closer to asphalt compared with SBS. It also has been confirmed from storage stability that the temperature susceptibility of grafted SBS modified asphalt was reduced in compare with SBS modified asphalt binder. As consequence, the use of grafted copolymer can be considered a suitable alternative for modification of asphalt binder in pavement.

scholarly journals Study on Viscoelastic Properties of Asphalt Mixtures Incorporating SBS Polymer and Basalt Fiber under Freeze–Thaw Cycles

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1804
Author(s):  
Wensheng Wang ◽  
Guojin Tan ◽  
Chunyu Liang ◽  
Yong Wang ◽  
Yongchun Cheng
Keyword(s):  
Viscoelastic Properties ◽  
Asphalt Mixture ◽  
Basalt Fiber ◽  
Asphalt Mixtures ◽  
Freeze Thaw ◽  
Static Creep ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Static Creep Test ◽  
Butadiene Styrene

This study aims to study the viscoelastic properties of asphalt mixtures incorporating styrene–butadiene–styrene (SBS) polymer and basalt fiber under freeze–thaw (F-T) cycles by using the static creep test. Asphalt mixture samples incorporating styrene–butadiene–styrene (SBS) polymer and basalt fiber were manufactured following the Superpave gyratory compaction (SGC) method and coring as well as sawing. After 0 to 21 F-T cycles processing, a uniaxial compression static creep test for the asphalt mixture specimens was performed to evaluate the influence of F-T cycles. The results indicated that the F-T cycles caused a larger creep deformation in the asphalt mixtures, which led to a decrease in the rut resistance of the asphalt mixtures incorporating SBS polymer and basalt fiber. Besides, the resistance to deformation decreased significantly in the early stage of F-T cycles. On the other hand, the viscoelastic parameters were analyzed to discuss the variation of viscoelastic characteristics. The relaxation time increased with F-T cycles, which will not be conducive to internal stress dissipation. Compared with lignin fiber, basalt fiber can improve the resistance to high-temperature deformation and the low-temperature crack resistance of asphalt mixtures under F-T cycles.

Influence of compaction temperature on rubberized asphalt mixes and binders

2008 ◽  
Vol 35 (9) ◽  
pp. 908-917 ◽  
Author(s):  
Soon-Jae Lee ◽  
Serji N. Amirkhanian ◽  
Khaldoun Shatanawi ◽  
Carl Thodesen
Keyword(s):  
Asphalt Binder ◽  
Asphalt Binders ◽  
Volumetric Properties ◽  
Asphalt Mixes ◽  
Compaction Temperature ◽  
Wide Range ◽  
Air Void ◽  
Styrene Butadiene ◽  
Main Factor ◽  
Butadiene Styrene

This research investigates the influence of compaction temperature on rubberized asphalt mixes and binders. For this, four Superpave mix designs for four asphalt binders (control, 3% styrene–butadiene–styrene (SBS)-modified, 10% rubber-modified, and 15% rubber-modified) were carried out. A total of 160 specimens were manufactured at four compaction temperatures of 116, 135, 154, and 173 °C. The binders were artificially short-term aged for 2 h at the mixture compaction temperatures prior to the binder tests. The results from this study showed that: (i) the control and SBS-modified mixtures could have almost the same air–void contents at a wide range of compaction temperatures; (ii) the compaction temperatures significantly affected the volumetric properties of the rubberized mixes; (iii) the aging difference of asphalt binder in the mixture depending on the compaction temperature is not considered to be a main factor affecting the volumetric properties of the mixtures.

scholarly journals Study on Styrene-Butadiene-Styrene Modified Asphalt Binders Relaxation at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2888
Author(s):  
Sylwia Dziadosz ◽  
Mieczysław Słowik ◽  
Filip Niwczyk ◽  
Marcin Bilski
Keyword(s):  
Low Temperature ◽  
Force Measurement ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Short Term ◽  
Modified Bitumen ◽  
Modified Asphalt ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Butadiene Styrene

The paper presents the results of laboratory investigation on asphalt binders relaxation at low temperature, carried out in a ductilometer using the tensile test with continuous force measurement. Polymer modified asphalt binder samples consisting of a 50/70 penetration grade bitumen mixed with a concentrate of styrene-butadiene-styrene (SBS) modified bitumen—a 160/220 penetration grade bitumen modified with a SBS copolymer in the amount of 9%—were tested. Therefore, polymer modified binders containing 3%, 4.5%, 6% and 7.5% SBS, respectively, were obtained and investigated. Tensile tests were performed at −16 °C on samples before aging and subjected to short-term aging (RTFOT). Test results in the form of relaxation curves have been mathematically described using a modified generalized Maxwell model. Based on the acquired results, it was shown that the increase of the SBS copolymer content in asphalt binder precipitates the relaxation process, while aging slows down this phenomenon. It has also been proven that with increased content of SBS elastomer in asphalt binder, the effect of short-term aging on binder’s stress relaxation ability at low temperatures is reduced.

scholarly journals Evaluation of rheological performance of a local modified bitumen by Styrene Butadiene Styrene polymer used in wearing course

2021 ◽  
Vol 15 (58) ◽  
pp. 65-76
Author(s):  
Kebaili Kebaili ◽  
Mohammed Boucherba ◽  
Mohamed Djouhri ◽  
Mustapha Kebaili
Keyword(s):  
Mechanical Performance ◽  
Road Construction ◽  
Modified Bitumen ◽  
Modification System ◽  
Styrene Butadiene Styrene ◽  
Bituminous Pavements ◽  
Styrene Butadiene ◽  
Objective Being ◽  
Bitumen Modification ◽  
Butadiene Styrene

In road construction, bitumen is the binder that gathered the different aggregates of road pavements. Bitumen, as a viscoelastic material, influences considerably the rheological behavior of bitumen concrete. The bitumen used in Algeria, showed its limits face to the traffic, which is increasing continuously. This research aims to valorize SBS polymer in wearing course by modifying a pure 35/50 bitumen. The present paper aims to study the polymer derived from styrene and butadiene (SBS) from the company Kraton Polymers International Ltd in the modification of a bitumen to improve its mechanical characteristics.To this end, the incorporation of SBS polymer was carried out according to two contents: 5.0 and 7.5% (by weight of asphalt), the objective being to evaluate the influence of this type of polymer on the rheological properties of the bitumen ordinary road including viscosity and modulus.The results reveal that the bitumen modified with 7.5% of SBS has better mechanical performance on the rigidity and the elasticity compared to the conventional bitumen. Recommendations have been made to implement a bitumen modification system to improve its quality and therefore the durability of bituminous pavements in the south of Algeria.

scholarly journals Evaluation of Moisture Susceptibility for Modified Open Graded Friction Course Mixes Used Styrene Butadiene Styrene

2019 ◽  
Vol 22 (2) ◽  
pp. 94-101
Author(s):  
Miran Bahyam Ahmed ◽  
Alaa Hussein Abed ◽  
Yasir Mawla Hammood Al-Badran
Keyword(s):  
Tensile Strength ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Moisture Susceptibility ◽  
Air Voids ◽  
Indirect Tensile ◽  
Asphalt Content ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Butadiene Styrene

Open-graded-fraction-course (OGFC), is a hot asphalt mixture usually utilized as a private purpose wearing course, because of open graded asphalt mixture and aggregates skeleton (stone-on-stone) contact, it contain a relatively high air voids’ percentage, after compaction which are permeable to water. In this research one type of gradation was used (12.5 mm) NMAS, to preparing the OGFC asphalt mixtures, penetration grade 40/50, crushed aggregate, asphalt content prepared with 4 % and up to 6 % by weight of mixture with 0.5 % increments. Optimum asphalt content (OAC) was selected based on these criteria, air voids content, asphalt draindown, permeability, and abrasion resistance (aged and un-aged) condition. The mix performance had been investigated by indirect tensile strength and moisture susceptibility (sensitivity) measured according to the (AASHTO T283-14). Results illustrate that the increasing of asphalt binder content leads to a decrease of the air voids content, abrasion loss and permeability values, while draindown increase, conversely, the indirect tensile strength (ITS) had been significantly increased for both conditions and this is a gaod suggestion to resistance alongside moisture susceptibility. It can be decided that the increasing of asphalt  binder percent in OGFC asphalt mixture, leads to an increase in the thickness of binder coating around the aggregates. On the other hand, the influence of modifier that prepared with 4% styrene-butadiene-styrene (SBS) on OGFC asphalt mixture tends to improve the mix properties and exhibit higher (TSR) as compared with original asphalt by (31, 27.7 and 24.4) % at asphalt percent (4.8, 5.3 and 5.8) %, respectively. The SBS improved the adhesion between aggregate and asphalt which leads to reduce stripping of HMA, horizontal deformation, and increased the tensile stiffness modulus value.

Sign in / Sign up

Export Citation Format

Share Document