scholarly journals Mechanical and Dynamic Behavior of an Elastic Rubber Layer with Recycled Styrene-Butadiene Rubber Granules

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3022
Author(s):  
Seongdo Kim ◽  
Hyun-Oh Shin ◽  
Doo-Yeol Yoo
Keyword(s):  
Tensile Properties ◽  
Curing Temperature ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Test Results ◽  
Elongation At Break ◽  
Curing Conditions ◽  
Rubber Layer ◽  
Elastic Rubber ◽  
Styrene Butadiene

This study evaluates the tensile properties, including the tensile strength and elongation at break, and dynamic behavior, including shock absorption and vertical deformation, of an elastic rubber layer in synthetic sports surfaces produced using waste tire chips containing styrene-butadiene rubber (SBR). The primary variables of the investigation were the number of compactions, resin–rubber granule ratio, and curing conditions, such as aging, the temperature, and the relative humidity. The test results showed an increase in the tensile strength of the elastic rubber layer with recycled SBR as the number of compactions, resin–rubber granule ratio, curing period, and temperature increased, while the elongation at break was affected by the curing temperature and period. Shock absorption and vertical deformation decreased with an increasing resin–rubber granule ratio and number of compactions due to the increased hardness. However, these properties were not significantly affected by the curing conditions. Furthermore, the test results indicated that the curing temperature has a pronounced effect on the tensile properties of the elastic rubber layer, and maintaining the appropriate curing temperature—approximately 50 °C—is a possible solution for improving the relatively low tensile properties of the elastic rubber layer.

scholarly journals Effects of alkanolamide addition on cure characteristics, crosslink density and tensile properties of carbon-black-filled styrene-butadiene rubber compounds

2018 ◽  
Vol 197 ◽  
pp. 12006 ◽  
Author(s):  
Indra Surya ◽  
Hanafi Ismail
Keyword(s):  
Tensile Strength ◽  
Carbon Black ◽  
Tensile Properties ◽  
Crosslink Density ◽  
Density Measurement ◽  
Tensile Modulus ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Cure Characteristics ◽  
Styrene Butadiene

By using a semi-efficient sulphur vulcanisation system, the effects of alkanolamide (ALK) addition on cure characteristics, crosslink density and tensile properties of carbon black (CB)-filled styrene-butadiene rubber (SBR) compounds were investigated. The ALK was prepared from Refined Bleached Deodorized Palm Stearin and diethanolamine and added into the CB-filled SBR compounds. The ALK loadings were 1.0, 3.0, 5.0 and 7.0 phr. It was found that ALK decreased the scorch and cure times of the CB-filled SBR compounds. ALK also improved the tensile modulus and tensile strength; especially up to a 5.0 phr of loading. The crosslink density measurement proved that the 5.0 phr of ALK exhibited the highest degree of crosslink density which caused the highest in tensile modulus and tensile strength. Due to its plasticity effect, ALK increased the elongation at break of the CB-filled SBR vulcanisates.

Using heat-treated starch to modify the surface of biochar and improve the tensile properties of biochar-filled styrene–butadiene rubber composites

2018 ◽  
Vol 51 (1) ◽  
pp. 26-35
Author(s):  
Steven C Peterson ◽  
Sanghoon Kim
Keyword(s):  
Tensile Properties ◽  
Styrene Butadiene Rubber ◽  
Filler Materials ◽  
Butadiene Rubber ◽  
Rubber Composites ◽  
Heat Treated ◽  
Matrix Interactions ◽  
Renewable Material ◽  
Styrene Butadiene ◽  
Properties Of Composites

Heat-treated starch (HTS) is a renewable material that can be used to modify the surface chemistry of small particles. In this work, HTS was used to coat hydrophilic biochar particles in order to make them more hydrophobic. Then, when added as filler to hydrophobic styrene–butadiene rubber (SBR), the coated biochar dispersed more easily and had enhanced filler–matrix interactions, which were reflected in the tensile properties of the final composites. Biochar particles modified with 5% (weight) HTS showed increases of 59% in the ultimate tensile strength, 49% in elongation percentage, and 79% in fracture toughness of SBR composites compared to unmodified biochar particles. This shows that HTS can be used to improve the tensile properties of composites filled with biochar and potentially other hydrophilic filler materials.

Influence of Novel Electron Beam Modified Surface Treated Dual Phase Filler on Rheometric and Mechanical Properties of Styrene Butadiene Rubber Vulcanizates

2003 ◽  
Vol 76 (2) ◽  
pp. 299-317 ◽  
Author(s):  
A. M. Shanmugharaj ◽  
Anil K. Bhowmick
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Styrene Butadiene Rubber ◽  
Dual Phase ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Polymer Filler ◽  
Modified Surface ◽  
Styrene Butadiene

Abstract Rheometric and mechanical properties, hysteresis and swelling behavior of the Styrene-Butadiene Rubber vulcanizates (SBR) filled with unmodified and novel electron beam modified surface treated dual phase fillers were investigated. Scorch time increases for these modified filler loaded vulcanizates due to introduction of quinone type oxygen on the surface. Electron beam modification of dual phase filler in the absence of trimethylol propanetriacrylate (TMPTA) or triethoxysilylpropyltetrasulphide (Si-69) significantly improves the modulus of the SBR vulcanizates, whereas the values of tensile strength and elongation at break drop. However, presence of TMPTA or silane slightly increases the modulus with significant improvement in tensile strength. This effect is more pronounced at higher loading of these modified fillers in SBR vulcanizates. These variations in modulus and tensile strength are explained by the equilibrium swelling data, Kraus plot and a new mathematical model interpreting the polymer-filler interaction. Hysteresis loss ratio of SBR vulcanizates loaded with irradiated fillers in absence and presence of TMPTA or silane increases due to highly aggregated structure of the filler.

Effect of Epoxidized Palm Oil Loading on the Swelling and Mechanical Properties of SBR Vulcanizates

2013 ◽  
Vol 812 ◽  
pp. 236-240
Author(s):  
Mohd Zaki Nurul Ayunie ◽  
Ahmad Zafir Romli ◽  
M.A. Wahab ◽  
Mohd Hanafiah Abidin
Keyword(s):  
Tensile Strength ◽  
Carbon Black ◽  
Palm Oil ◽  
Crosslink Density ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Epoxidized Palm Oil ◽  
Opposite Trend ◽  
Styrene Butadiene

The effects of epoxidized palm oil (EPO) content in carbon black filled styrene butadiene rubber (SBR) on tensile strength, elongation at break and crosslink density were investigated. Five different loadings of EPO in parts per hundred rubbers (phr) were used to test the tensile strength of the carbon black filled SBR which showed a decreasing trend as the content of EPO in the vulcanizates increased. In contrast, elongation at break showed the opposite trend where the elongation at break increased as the content of the EPO increased. The SBR vulcanizates with the highest content of EPO gave the highest value of elongation at break which is 2393.56%. In the case of swelling index, it was found to increase as the amount of EPO increased.

scholarly journals Influence of trans-polyoctylene rubber content on styrene-butadiene rubber properties

2020 ◽  
Vol 13 (1) ◽  
pp. 1-5
Author(s):  
Patrik Macúrik ◽  
Rafal Anyszka ◽  
Ivan Hudec ◽  
Terézia Malčeková ◽  
Ján Kruželák
Keyword(s):  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Curing Time ◽  
Cross Link ◽  
Rubber Content ◽  
Elongation At Break ◽  
Rubber Compounds ◽  
Link Density ◽  
Cross Link Density ◽  
Styrene Butadiene

AbstractThe study was focused on the investigation of trans-polyoctylene (TOR) influence on cross-linking as well as mechanical and rheological properties of rubber compounds based on styrene-butadiene rubber (SBR). SBR was compounded with different proportions of TOR in the concentration range from 0 to 30 phr. Integration of TOR into rubber leads to the prolongation of the optimum curing time and scorch time and thus the decrease of the curing rate. Higher content of TOR led to less viscous rubber due to the plasticizing effect. Cross-link density of vulcanizates was reduced, which correlates with higher elongation at break. Tensile strength and hardness of vulcanizates increased with the increasing TOR content, probably due to the increasing amount of the crystalline phase.

scholarly journals Mechanical Properties of Water Purification Industry Used Natural Rubber/Styrene-Butadiene Rubber Blends that Prepared Via Different Sulfur Curing Systems

2020 ◽  
Author(s):  
Wenfa Dong ◽  
Ruogu Tang
Keyword(s):  
Mechanical Properties ◽  
Relative Volume ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Water Industry ◽  
High Modulus ◽  
Elongation At Break ◽  
Tear Strength ◽  
Rubber Blends ◽  
Styrene Butadiene

<div>The water industry used NR was selected for blending with SBR. A series of NR/SBR vulcanizates were prepared through three different vulcanization systems, conventional vulcanization (CV), effective vulcanization (EV) and semi-effective vulcanization (SEV) respectively, basing on each formulation and optimum curing time. We examined the mechanical properties of NR/SBR vulcanizates including tensile strength, tear strength, elongation at break, modulus, Shore A hardnessand and relative volume abrasion. The results indicated that NR/SBR vulcanizates prepared in different systems differed in mechanical properties. Vulcanizates prepared via CV showed higher tensile and tear strength; vulcanizates prepared via EV had high modulus and hardness, and vulcanizates prepared via SEV performed high abrasion resistance. </div>

scholarly journals Investigation on tensile properties of epoxy/graphene nano-platelets/carboxylated nitrile butadiene rubber ternary nanocomposites using response surface methodology

2019 ◽  
Vol 9 ◽  
pp. 184798041985584 ◽  
Author(s):  
Mohammadhossein Saberian ◽  
Faramarz Ashenai Ghasemi ◽  
Ismail Ghasemi ◽  
Sajjad Daneshpayeh
Keyword(s):  
Tensile Strength ◽  
Response Surface Methodology ◽  
Tensile Properties ◽  
Response Surface ◽  
Tensile Modulus ◽  
Curing Temperature ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Low Concentration ◽  
Nitrile Butadiene Rubber

In this study, the response surface methodology was used to investigate the tensile properties of epoxy/graphene nano-platelets/carboxylated nitrile butadiene rubber ternary nanocomposites. Box–Benhken method was used to design experiments for four factors consisting of graphene nano-platelets (at 0, 0.75, and 1.5 wt%), carboxylated nitrile butadiene rubber (0, 5, and 10 wt%), hardener contents (80, 90, and 100 phr), and also different post curing temperature (130, 140, and 150°C). After the samples were prepared, a tensile test was performed to obtain the tensile strength, tensile modulus, and elongation at break of nanocomposites. Moreover, field-emission scanning electron microscopy was used to observe the state of graphene nano-platelets dispersion. The results obtained from the tensile tests showed that increasing the graphene nano-platelets, carboxylated nitrile butadiene rubber, and hardener contents and high post curing temperature reduced the tensile strength. The optimum value of tensile modulus was achieved at low concentration of carboxylated nitrile butadiene rubber and high contents of graphene nano-platelets, whereas maximum elongation at break occurred at high content of carboxylated nitrile butadiene rubber and low concentration of graphene nano-platelets and hardener. In addition, a second-order polynomial model was used to correlate the tensile properties of ternary nanocomposites to the desired factors. Finally, contour plots were used to determine optimum values of the desired factors. It was seen that the presence of 10 wt% of carboxylated nitrile butadiene rubber in the epoxy matrix increased the elongation at break by the considerable amount of ∼49%.

The Vulcanization of Styrene-Butadiene Rubber with 2-Pentadecyl-Benzoquinone Dioxime

1979 ◽  
Vol 52 (2) ◽  
pp. 353-360 ◽  
Author(s):  
N. D. Ghatge ◽  
N. N. Maldar
Keyword(s):  
Tensile Strength ◽  
Raw Material ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Red Lead ◽  
Styrene Butadiene ◽  
Resistance To Heat ◽  
Curing Systems ◽  
Sulfur Curing

Abstract The authors propose a new active vulcanizing agent 2-pentadecylbenzo-quinone dioxime, derivable from the indigenous raw material, cashewnutshell liquid. This vulcanizing agent, when oxidized by red lead, gives styrene-butadiene vulcanizates of improved tensile strength and elongation at break, compared to vulcanizates cured by p-benzoquinone dioxime, 2-methylbenzo-quinone dioxime or standard sulfur curing systems. The new vulcanizates have much greater resistance to heat aging than the corresponding sulfur vulcanisates.

Influence of Polymer Latex on the Interlayer Bonding Performance of Cement Concrete

2014 ◽  
Vol 1065-1069 ◽  
pp. 1780-1783 ◽  
Author(s):  
Tai Xiu Yang ◽  
Jing Zhu
Keyword(s):  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Test Results ◽  
Cement Concrete ◽  
Bonding Performance ◽  
Interface Agent ◽  
Bonding Properties ◽  
Interlayer Bonding ◽  
Styrene Butadiene ◽  
The Impact

Adding polymer into cement concrete is used to increase the interlayer bonding performance. The impact of polymer on the interlayer bonding performance was studied by shear strength and tensile strength test. The mix design of the interface agent was optimized through the tensile bending tests of different fiber and polymer dosage. The impact of casting methods and interface agent mix was studied through tests. The test results show that: adding organic fiber and polymer into cement concrete could significantly increase the interlayer bond strength. The interface agent of SBR (styrene-butadiene rubber) latex modified cement paste has better tensile bonding properties. When the ratio of cement to DB-1 latex is 3:2, it will effectively increase the interlayer bonding performance of cement concrete.

Sign in / Sign up

Export Citation Format

Share Document