scholarly journals Promoting Interfacial Interactions with the Addition of Lignin in Poly(Lactic Acid) Hybrid Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 272
Author(s):  
Bindu Patanair ◽  
Allisson Saiter-Fourcin ◽  
Sabu Thomas ◽  
Martin George Thomas ◽  
Poornima Parathukkamparambil Pundarikashan ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Amorphous Phase ◽  
Lignin Content ◽  
Glassy State ◽  
Hybrid Nanocomposites ◽  
Poly Lactic Acid ◽  
Multiwalled Carbon ◽  
Cloisite 30B ◽  
Reduced Graphene ◽  
Rigid Amorphous

In this paper, the calorimetric response of the amorphous phase was examined in hybrid nanocomposites which were prepared thanks to a facile synthetic route, by adding reduced graphene oxide (rGO), Cloisite 30B (C30B), or multiwalled carbon nanotubes (MWCNT) to lignin-filled poly(lactic acid) (PLA). The dispersion of both lignin and nanofillers was successful, according to a field-emission scanning-electron microscopy (FESEM) analysis. Lignin alone essentially acted as a crystallization retardant for PLA, and the nanocomposites shared this feature, except when MWCNT was used as nanofiller. All systems exhibiting a curtailed crystallization also showed better thermal stability than neat PLA, as assessed from thermogravimetric measurements. As a consequence of favorable interactions between the PLA matrix, lignin, and the nanofillers, homogeneous dispersion or exfoliation was assumed in amorphous samples from the increase of the cooperative rearranging region (CRR) size, being even more remarkable when increasing the lignin content. The amorphous nanocomposites showed a signature of successful filler inclusion, since no rigid amorphous fraction (RAF) was reported at the filler/matrix interface. Finally, the nanocomposites were crystallized up to their maximum extent from the glassy state in nonisothermal conditions. Despite similar degrees of crystallinity and RAF, significant variations in the CRR size were observed among samples, revealing different levels of mobility constraining in the amorphous phase, probably linked to a filler-dimension dependence of space filling.

Raman spectroscopic study of conformational changes in the amorphous phase of poly(lactic acid) during deformation

Polymer ◽  
2004 ◽  
Vol 45 (12) ◽  
pp. 4241-4248 ◽  
Author(s):  
Xiaozhen Yang ◽  
Shuhui Kang ◽  
Yuning Yang ◽  
Kaoru Aou ◽  
Shaw Ling Hsu
Keyword(s):  
Lactic Acid ◽  
Spectroscopic Study ◽  
Amorphous Phase ◽  
Conformational Changes ◽  
Poly Lactic Acid ◽  
Raman Spectroscopic ◽  
Raman Spectroscopic Study

Rheology of poly(lactic acid)/poly(trimethylene terephthalate) blends compatibilized by clay or maleic anhydride-grafted poly(ethylene-octene) elastomer

2019 ◽  
Vol 39 (3) ◽  
pp. 248-253
Author(s):  
Gwo-Geng Lin ◽  
Yi-Hu Song ◽  
Chao-Tsai Huang ◽  
Marek Sipos ◽  
Zhaokang Tu
Keyword(s):  
Lactic Acid ◽  
Maleic Anhydride ◽  
Low Frequency ◽  
Complex Viscosity ◽  
Fold Increase ◽  
Poly Lactic Acid ◽  
Morphology Evolution ◽  
Cloisite 30B ◽  
Trimethylene Terephthalate ◽  
Poly Ethylene

Abstract Blends of two biobased polymers, poly(lactic acid) and poly(trimethylene terephthalate) (PTT), were compatibilized with either maleic anhydride-grafted poly(ethylene-octene) (mPOE) or organically modified clay (Cloisite 30B). Dynamic rheological measurements revealed that the mPOE inclusion resulted in a four-fold increase in viscosity relative to the noncompatibilized blends. By loading 3 wt% Cloisite 30B, the storage moduli of the blends showed a distinct solid-like behavior and high complex viscosity in the low-frequency region, which can be interpreted by the reduced sizes of the PTT phase evidenced from the scanning electron microscopy (SEM) micrography. A temperature sweep of the viscosity of the blends starting from 180°C revealed that the existence of an unmelted PTT dispersed phase might impede the decline in viscosity with increasing temperature near the melting point of PTT. The introduced compatibilizers can restrict the temperature-dependent morphology evolution, and the use of the 3 wt% 30B clay can prohibit the morphology evolution during the temperature sweep.

The role of multiwall carbon nanotubes on physical, mechanical and rheological properties of poly(lactic acid)/natural rubber/CNT hybrid systems

2020 ◽  
pp. 096739112093135
Author(s):  
Mohammad Mahdi Salehi ◽  
Fatemeh Hakkak
Keyword(s):  
Lactic Acid ◽  
Natural Rubber ◽  
Rheological Properties ◽  
Droplet Size ◽  
Multiwall Carbon Nanotubes ◽  
Droplet Size Distribution ◽  
Hybrid Nanocomposites ◽  
Poly Lactic Acid ◽  
Melt Mixing

The main objective of the present work was to study the role of carbon nanotube (CNT) on the microstructure development and physical, mechanical, and rheological properties of poly(lactic acid) (PLA)/natural rubber (NR)/CNT hybrid nanocomposites. The PLA/NR blend samples with constant blend ratio (90/10) were prepared by melt mixing in a laboratory internal mixer at a temperature of 190°C. The behavior of the PLA/NR blend was examined depending on the CNT content (0.5–6 wt%). The droplet size and droplet size distribution of the NR phase decreases with the increase in CNTs content. This could be explained in terms of compatibilizing effect of CNT and the changing of the viscosity ratio of the blend phases. The development of the microstructure and the physical properties of the blend were also investigated according to the CNT contents by measuring the linear viscoelasticity. The elongational behavior and mechanical properties of the blends were strongly dependent on the location of the CNT. The CNT worked as an efficient compatibilizer and also it worked as a reinforcing filler making the matrix more rigid.

scholarly journals Influence of the Lignin Content on the Properties of Poly(Lactic Acid)/lignin-Containing Cellulose Nanofibrils Composite Films

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 1013 ◽  
Author(s):  
Xuan Wang ◽  
Yuan Jia ◽  
Zhen Liu ◽  
Jiaojiao Miao
Keyword(s):  
Lactic Acid ◽  
Lignin Content ◽  
Cellulose Nanofibrils ◽  
Composite Films ◽  
Tensile Tests ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry

Poly(lactic acid) (PLA)/lignin-containing cellulose nanofibrils (L-CNFs) composite films with different lignin contents were produced bythe solution casting method. The effect of the lignin content on the mechanical, thermal, and crystallinity properties, and PLA/LCNFs interfacial adhesion wereinvestigated by tensile tests, thermogravimetric analysis, differential scanning calorimetry (DSC), dynamic mechanical analysis, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The tensile strength and modulus of the PLA/9-LCNFs (9 wt % lignin LCNFs) composites are 37% and 61% higher than those of pure PLA, respectively. The glass transition temperature (Tg) decreases from 61.2 for pure PLA to 52.6 °C for the PLA/14-LCNFs (14 wt % lignin LCNFs) composite, and the composites have higher thermal stability below 380 °C than pure PLA. The DSC results indicate that the LCNFs, containing different lignin contents, act as a nucleating agent to increase the degree of crystallinity of PLA. The effect of the LCNFs lignin content on the PLA/LCNFs compatibility/adhesion was confirmed by the FTIR, SEM, and Tg results. Increasing the LCNFs lignin content increases the storage modulus of the PLA/LCNFs composites to a maximum for the PLA/9-LCNFs composite. This study shows that the lignin content has a considerable effect on the strength and flexibility of PLA/LCNFs composites.

scholarly journals Composites Based on Poly(Lactic Acid) (PLA) and SBA-15: Effect of Mesoporous Silica on Thermal Stability and on Isothermal Crystallization from Either Glass or Molten State

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2743
Author(s):  
Tamara M. Díez-Rodríguez ◽  
Enrique Blázquez-Blázquez ◽  
Ernesto Pérez ◽  
María L. Cerrada
Keyword(s):  
Lactic Acid ◽  
Mesoporous Silica ◽  
Isothermal Crystallization ◽  
Physical Aging ◽  
Glassy State ◽  
Poly Lactic Acid ◽  
Molten State ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

Several composites based on an L-rich poly(lactic acid) (PLA) with different contents of mesoporous Santa Barbara Amorphous (SBA-15) silica were prepared in order to evaluate the effect of the mesoporous silica on the resultant PLA materials by examining morphological aspects, changes in PLA phases and their transitions, and, primarily, the influence on some final properties. Melt extrusion was chosen for the obtainment of the composites, followed by quenching from the melt to prepare films. Completely amorphous samples were then attained, as deduced from X-ray diffraction and differential scanning calorimetry (DSC) analyses. Thermogravimetric analysis (TGA) results demonstrated that the presence of SBA-15 particles in the PLA matrix did not exert any significant influence on the thermal decomposition of these composites. An important nucleation effect of the silica was found in PLA, especially under isothermal crystallization either from the melt or from its glassy state. As expected, isothermal crystallization from the glass was considerably faster than from the molten state, and these high differences were also responsible for a more considerable nucleating role of SBA-15 when crystallizing from the melt. It is remarkable that the PLA under analysis showed very close temperatures for cold crystallization and its subsequent melting. Moreover, the type of developed polymorphs did not accomplish the common rules previously described in the literature. Thus, all the isothermal experiments led to exclusive formation of the α modification, and the observation of the α’ crystals required the annealing for long times at temperatures below 80 °C, as ascertained by both DSC and X-ray diffraction experiments. Finally, microhardness (MH) measurements indicated a competition between the PLA physical aging and the silica reinforcement effect in the as-processed amorphous films. Physical aging in the neat PLA was much more important than in the PLA matrix that constituted the composites. Accordingly, the MH trend with SBA-15 content was strongly dependent on aging times.

Sign in / Sign up

Export Citation Format

Share Document