scholarly journals Preparation and Characterization of Highly Porous Polyacrylonitrile Electrospun Nanofibers Using Lignin as Soft Template via Selective Chemical Dissolution Technique

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3938
Author(s):  
Mohd Adib Tajuddin Ahmad ◽  
Norizah Abdul Rahman
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Electrospun Nanofibers ◽  
Soft Template ◽  
Chemical Dissolution ◽  
Electrospinning Technique ◽  
Average Pore ◽  
Selective Chemical ◽  
Highly Porous

In this study, polyacrylonitrile (PAN) was mixed with a renewable polymer, lignin, to produce electrospun nanofibers by using an electrospinning technique. Lignin was utilized as a soft template that was removed from the nanofibers by using a selective dissolution technique to create porous PAN nanofibers. These nanofibers were characterized with Fourier transform infrared (FTIR), field emission scanning electron microscopy (FESEM), thermogravimetry analysis (TGA), X-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) to study their properties and morphology. The results showed that lignin can be homogeneously mixed into the PAN solution and successfully electrospun into nanofibers. FESEM results showed a strong relationship between the PAN: lignin ratio and the diameter of the electrospun fibers. Lignin was successfully removed from electrospun nanofibers by a selective chemical dissolution technique, which resulted in roughness and porousness on the surface of the nanofibers. Based on the BET result, the specific surface area of the PAN/lignin nanofibers was more than doubled following the removal of lignin compared to PAN nanofibers. The highest specific surface area of nanofibers after selective chemical dissolution was found at an 8:2 ratio of PAN/lignin, which was 32.42 m2g−1 with an average pore diameter of 5.02 nm. The diameter of electrospun nanofibers was also slightly reduced after selective chemical dissolution. Porous PAN nanofibers can be seen as the precursors to the production of highly porous carbon nanofibers.

Fuels Desulphurisation by Adsorbtion on Fe / Bentonite

2017 ◽  
Vol 68 (3) ◽  
pp. 483-486
Author(s):  
Constantin Sorin Ion ◽  
Mihaela Bombos ◽  
Gabriel Vasilievici ◽  
Dorin Bombos
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Adsorption Process ◽  
Continuous System ◽  
Gas Oil ◽  
Average Pore ◽  
Atmospheric Distillation

Desulfurisation of atmospheric distillation gasoline and gas oil was performed by adsorption process on Fe/ bentonite. The adsorbent was characterized by determining the adsorption isotherms, specific surface area, pore volume and average pore diameter. Adsorption experiments of atmospheric distillation gasoline and gas oil were performed in continuous system at 280�320oC, 5 atm and volume hourly space velocities of 1�2 h-1. The efficiency of adsorption on Fe / bentonite was better at desulphurisation of gasoline versus gas oil.

scholarly journals Acid Modification of the Unsupported NiMo Catalysts by Y-Zeolite Nanoclusters

Crystals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 344
Author(s):  
Chengwu Dong ◽  
Changlong Yin ◽  
Tongtong Wu ◽  
Zhuyan Wu ◽  
Dong Liu ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Pore Size ◽  
Y Zeolite ◽  
Active Components ◽  
Acid Modification ◽  
Total Acid ◽  
Average Pore ◽  
Nimo Catalysts

Unsupported NiMo catalyst has high hydrogenation activity due to its high active site distribution. However, low specific surface area and pore distribution greatly limit the efficient utilization of the active components. The Y-zeolite nanoclusters were hydrothermally synthesized and introduced into the unsupported NiMo catalysts from a layered nickel molybdate complex oxide. The XRD, N2 adsorption-desorption, FT-IR, Py-IR, SEM, NH3-TPD, and TEM were used to characterize all catalysts. The dibenzothiophene (DBT) hydrodesulfurization (HDS) reaction was performed in a continuous high pressure microreactor. The results showed that the specific surface area, pore volume, and average pore size of the unsupported NiMo catalysts were greatly increased by the Y-zeolite nanoclusters, and a more dispersed structure was produced. Furthermore, the Lewis acid and total acid content of the unsupported NiMo catalysts were greatly improved by the Y-zeolite nanoclusters. The HDS results showed that the unsupported NiMo catalysts modified by the nanoclusters had the same high desulfurization efficiency as the unmodified catalyst, but had more proportion of direct desulfurization (DDS) products. The results offer an alternative to reducing hydrogen consumption and save cost in the production of ultra clean diesel.

scholarly journals Biodiesel Processing Using Sodium and Potassium Geopolymer Powders as Heterogeneous Catalysts

Molecules ◽  
2020 ◽  
Vol 25 (12) ◽  
pp. 2839 ◽  
Author(s):  
Renata F. Botti ◽  
Murilo D.M. Innocentini ◽  
Thais A. Faleiros ◽  
Murilo F. Mello ◽  
Danilo L. Flumignan ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Heterogeneous Catalysts ◽  
Average Pore Size ◽  
Thermal Shrinkage ◽  
Average Pore ◽  
Base Catalysts ◽  
Sodium And Potassium

This work investigates the catalytic activity of geopolymers produced using two different alkali components (sodium or potassium) and four treatment temperatures (110 to 700 °C) for the methyl transesterification of soybean oil. The geopolymers were prepared with metakaolin as an aluminosilicate source and alkaline activating solutions containing either sodium or potassium in the same molar oxide proportions. The potassium-based formulation displayed a higher specific surface area and lower average pore size (28.64–62.54 m²/g; 9 nm) than the sodium formulation (6.34–32.62 m²/g; 17 nm). The reduction in specific surface area (SSA) after the heat treatment was more severe for the sodium formulation due to the higher thermal shrinkage. The catalytic activity of the geopolymer powders was compared under the same reactional conditions (70–75 °C, 150% methanol excess, 4 h reaction) and same weight amounts (3% to oil). The differences in performance were attributed to the influences of sodium and potassium on the geopolymerization process and to the accessibility of the reactants to the catalytic sites. The Na-based geopolymers performed better, with FAME contents in the biodiesel phase of 85.1% and 89.9% for samples treated at 500 and 300 °C, respectively. These results are competitive in comparison with most heterogeneous base catalysts reported in the literature, considering the very mild conditions of temperature, excess methanol and catalyst amount and the short time spent in reactions.

Polyhedral oligomeric silsesquioxane as a recyclable soft template to synthesize mesoporous polymeric carbon nitride with enhanced photocatalytic hydrogen evolution

2021 ◽  
Vol 5 (1) ◽  
pp. 112-116
Author(s):  
Zhiwei Liang ◽  
Lei Liu ◽  
Xiaojia Zhuang ◽  
Zicheng Tang ◽  
Haiping Li ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Hydrogen Evolution ◽  
Specific Surface Area ◽  
Carbon Nitride ◽  
Polyhedral Oligomeric Silsesquioxane ◽  
Soft Template ◽  
Photocatalytic Hydrogen Evolution ◽  
Oligomeric Silsesquioxane ◽  
Polymeric Carbon

A novel recyclable template was used to prepare mesoporous polymeric carbon nitride with prominently increased specific surface area and photoactivity.

Nano/Micro Pore Structure and Fractal Characteristics of Baliancheng Coalfield in Hunchun Basin

2021 ◽  
Vol 21 (1) ◽  
pp. 682-692
Author(s):  
Youzhi Wang ◽  
Cui Mao
Keyword(s):  
Fractal Dimension ◽  
Specific Surface ◽  
Pore Structure ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Diameter ◽  
Fractal Dimensions ◽  
Nitrogen Adsorption ◽  
Average Pore ◽  
Coal Reservoir

The pore structure characteristic is an important index to measure and evaluate the storage capacity and fracturing coal reservoir. The coal of Baliancheng coalfield in Hunchun Basin was selected for experiments including low temperature nitrogen adsorption method, Argon Ion milling Scanning Electron Microscopy (Ar-SEM), Nuclear Magnetic Resonance (NMR), X-ray diffraction method, quantitative mineral clay analysis method. The pore structure of coal was quantitatively characterized by means of fractal theory. Meanwhile, the influences of pores fractal dimension were discussed with experiment data. The results show that the organic pores in Baliancheng coalfield are mainly plant tissue pores, interparticle pores and gas pores, and the mineral pores are corrosion pores and clay mineral pores. There are mainly slit pore and wedge-shaped pore in curve I of Low temperature nitrogen adsorption. There are ink pores in curve II with characteristics of a large specific surface area and average pore diameter. The two peaks of NMR T2 spectrum indicate that the adsorption pores are relatively developed and their connectivity is poor. The three peaks show the seepage pores and cracks well developed, which are beneficial to improve the porosity and permeability of coal reservoir. When the pore diameter is 2–100 nm, the fractal dimensions D1 and D2 obtained by nitrogen adsorption experiment. there are positive correlations between water content and specific surface area and surface fractal dimension D1, The fractal dimension D2 was positively and negatively correlated with ash content and average pore diameters respectively. The fractal dimensions DN1 and DN2 were obtained by using the NMR in the range of 0.1 μm˜10 μm. DN1 are positively correlated with specific surface area of adsorption pores. DN2 are positively correlated volume of seepage pores. The fractal dimension DM and dissolution hole fractal dimension Dc were calculated by SEM image method, respectively controlled by clay mineral and feldspar content. There is a remarkable positive correlation between D1 and DN1 and Langmuir volume of coal, so fractal dimension can effectively quantify the adsorption capacity of coal.

scholarly journals PREPARATION OF MESOPOROUS TITANIA-SILICA AEROGELS BY CO2 SUPERCRITICAL EXTRACTION

2010 ◽  
Vol 7 (2) ◽  
pp. 121-127
Author(s):  
Silvester Tursiloadi ◽  
Dinie Mansur ◽  
Yeny Meliana ◽  
Ruslan Efendi
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Thermal Evolution ◽  
Anatase Phase ◽  
Sol Gel ◽  
Total Pore Volume ◽  
Acid Catalyst ◽  
Supercritical Extraction ◽  
Average Pore

Stable anatase is attractive because of its notable functions for photocatalysis and photon-electron transfer.  TiO2-nanoparticles dispersed SiO2 wet gels were prepared by hydrolysis of Ti(OC4H9n)4 and Si(OC2H5)4 in a 2-propanol solution with acid catalyst.  The solvent in the wet gels was supercritically extracted using CO2 at 60 oC and 22 Mpa in one-step.  Thermal evolution of the microstructure of the extracted gels (aerogels) was evaluated by XRD measurements, TEM and N2 adsorption measurements. The as-extracted aerogel with a large specific surface area, more than 365 m2g-1, contained anatase nanoparticles, about 5 nm in diameter.  The anatase phase was stable after calcinations at temperatures up to 1000 oC, and BET specific surface area, total pore volume and average pore diameter did not change significantly after calcinations at temperature up to 800 oC.   Keywords: Stable anatase, sol-gel, CO2 supercritical extraction.

Synergy of Pore Size and Specific Surface Area on the CO2 Sorption Performance of Nano CaO-Based Sorbents

2019 ◽  
Vol 19 (6) ◽  
pp. 3205-3209 ◽  
Author(s):  
Shangqing Lu ◽  
Qirui Lin ◽  
Sufang Wu
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Sorption Capacity ◽  
Specific Surface Area ◽  
Partial Correlation ◽  
Average Pore Size ◽  
Partial Correlation Analysis ◽  
Average Pore ◽  
Carbon Dioxide Sorption

This study focuses on the synergy effect of pore size and specific surface area (SSA) on the carbon dioxide sorption performance. Nano CaO-based CO2 sorbents with various pore size (15–55 nm) under similar SSA, and different SSA (14.50–48.90 m2/g) under similar pore size are prepared using selected organic templates. Results indicate that increasing the proportion of macropore in 47–96 nm could significantly improve sorbent’s sorption rate and corresponding sorption capacity. Besides, sorption capacity could be also by SSA. Moreover, partial correlation analysis reveals that sorption capacity is slightly more dependent on average pore size than SSA.

Preparation and Structural Analysis of Magnesium Oxide Aerogels

MRS Advances ◽  
2017 ◽  
Vol 2 (57) ◽  
pp. 3505-3510
Author(s):  
Jiankai Zhang ◽  
Xiaohong Chen ◽  
Ran Liu ◽  
Huaihe Song ◽  
Zhihong Li
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Magnesium Oxide ◽  
Specific Surface Area ◽  
Average Pore Size ◽  
Sol Gel ◽  
Average Pore ◽  
X Ray ◽  
Water As Solvent ◽  
Saxs Analysis

ABSTRACTMagnesium oxide aerogels were made by sol-gel process using magnesium methoxide as precursor, methanol and deionized water as solvent with ethanol supercritical fluid drying. The influences of the different factors on the gel time and the specific surface area of magnesium oxide aerogels were studied, and the structure and morphology were characterized by Scanning Electron Microscopy (SEM), Transmission Electron Microscope (TEM) and X-ray diffraction (XRD), and the Small Angle X-ray Scatter (SAXS) was utilized to determine the fractural structure of the magnesium oxide aerogels. The results show that MgO aerogels belong to the typical mesoporous materials with rich network and highly developed pore structure, and the specific surface area is 904.9 m2/g, the apparent density is 0.055 g/cm3, the average pore size is 19.6 nm. The results of SAXS analysis show that the fractal dimension of the MgO aerogels is 2.32 in high q area which proves the existence of rough surface and pore fractal structure.

scholarly journals COMPARISON OF PORE FRACTAL CHARACTERISTICS BETWEEN MARINE AND CONTINENTAL SHALES

Fractals ◽  
2018 ◽  
Vol 26 (02) ◽  
pp. 1840016 ◽  
Author(s):  
JUN LIU ◽  
YANBIN YAO ◽  
DAMENG LIU ◽  
YIDONG CAI ◽  
JIANCHAO CAI
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Clay Minerals ◽  
Specific Surface Area ◽  
Pore Diameter ◽  
Fractal Dimensions ◽  
Average Pore Diameter ◽  
Average Pore ◽  
Dimension Formula ◽  
Marine Shale

Fractal characterization offers a quantitative evaluation on the heterogeneity of pore structure which greatly affects gas adsorption and transportation in shales. To compare the fractal characteristics between marine and continental shales, nine samples from the Lower Silurian Longmaxi formation in the Sichuan basin and nine from the Middle Jurassic Dameigou formation in the Qaidam basin were collected. Reservoir properties and fractal dimensions were characterized for all the collected samples. In this study, fractal dimensions were originated from the Frenkel–Halsey–Hill (FHH) model with N[Formula: see text] adsorption data. Compared to continental shale, marine shale has greater values of quartz content, porosity, specific surface area and total pore volume but lower level of clay minerals content, permeability, average pore diameter and methane adsorption capacity. The quartz in marine shale is mostly associated with biogenic origin, while that in continental shale is mainly due to terrigenous debris. The N[Formula: see text] adsorption–desorption isotherms exhibit that marine shale has fewer inkbottle-shaped pores but more plate-like and slit-shaped pores than continental shale. Two fractal dimensions ([Formula: see text] and [Formula: see text] were obtained at [Formula: see text] of 0–0.5 and 0.5–1. The dimension [Formula: see text] is commonly greater than [Formula: see text], suggesting that larger pores (diameter [Formula: see text][Formula: see text]nm) have more complex structures than small pores (diameter [Formula: see text][Formula: see text]nm). The fractal dimensions (both [Formula: see text] and [Formula: see text]) positively correlate to clay minerals content, specific surface area and methane adsorption capacity, but have negative relationships with porosity, permeability and average pore diameter. The fractal dimensions increase proportionally with the increasing quartz content in marine shale but have no obvious correlation with that in continental shale. The dimension [Formula: see text] is correlative to the TOC content and permeability of marine shale at a similar degree with dimension [Formula: see text], while the dimension [Formula: see text] is more sensitive to those of continental shale than dimension [Formula: see text]. Compared with dimension [Formula: see text], for two shales, dimension [Formula: see text] is better associated with the content of clay minerals but has worse correlations with the specific surface area and average pore diameter.

Synthesis, Characterisation, and Photocatalytic Behaviour of Mesoporous ZnS Nanoparticles Prepared Using By-Product Templating

2017 ◽  
Vol 70 (10) ◽  
pp. 1099 ◽  
Author(s):  
Hosein B. Motejadded Emrooz ◽  
Ali R. Rahmani ◽  
Francisco J. Gotor
Keyword(s):  
Electron Microscopy ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Diffuse Reflectance Spectroscopy ◽  
High Surface ◽  
Ultrasonic Waves ◽  
Soft Template ◽  
Bandgap Energy ◽  
Zns Nanoparticles

High surface area mesoporous ZnS nanoparticles (MZN) were obtained with the aid of the by-product of the synthesising reaction. This by-product, namely NaNO3, can be considered as a soft template responsible for the formation of pores. Ethanol and water were chosen as the synthesis media. Ultrasonic waves were used as an accelerator for the synthesis of MZNs. Photocatalytic activities of the synthesised samples for the degradation of methylene blue (MB) were investigated under ultraviolet irradiation. Synthesised specimens were characterised using field emission scanning electron microscopy, transmission electron microscopy, powder X-ray diffraction, diffuse reflectance spectroscopy, N2-physisorption, and FT-IR spectroscopy. Results indicated that the synthesis media has a pronounced effect on the surface properties of the final porous particles by several mechanisms. The specific surface area of the MZN samples synthesised in water and ethanol were determined to be 53 and 201 m2 g−1, respectively. The difference in the specific surface area was attributed to the weak solvation of S2− ions (Na2S·5H2O in ethanol) and also to the by-product of the synthesis reaction. The photocatalytic behaviour of the mesoporous ZnS nanoparticles synthesised in these two media were investigated and the results have been interpreted with the aid of effective surface area, pore volume, and bandgap energy of the specimens.

Sign in / Sign up

Export Citation Format

Share Document