scholarly journals Physically-Based Retrieval of Canopy Equivalent Water Thickness Using Hyperspectral Data

2018 ◽  
Vol 10 (12) ◽  
pp. 1924 ◽  
Author(s):  
Matthias Wocher ◽  
Katja Berger ◽  
Martin Danner ◽  
Wolfram Mauser ◽  
Tobias Hank
Keyword(s):  
Water Content ◽  
Optical Sensors ◽  
Land Surface ◽  
Hyperspectral Data ◽  
Canopy Reflectance ◽  
Area Index ◽  
Equivalent Water Thickness ◽  
Crop Type ◽  
Physically Based ◽  
Leaf Level

Quantitative equivalent water thickness on canopy level (EWTcanopy) is an important land surface variable and retrieving EWTcanopy from remote sensing has been targeted by many studies. However, the effect of radiative penetration into the canopy has not been fully understood. Therefore, in this study the Beer-Lambert law is applied to inversely determine water content information in the 930 to 1060 nm range of canopy reflectance from measured winter wheat and corn spectra collected in 2015, 2017, and 2018. The spectral model was calibrated using a look-up-table (LUT) of 50,000 PROSPECT spectra. Internal model validation was performed using two leaf optical properties datasets (LOPEX93 and ANGERS). Destructive in-situ measurements of water content were collected separately for leaves, stalks, and fruits. Correlation between measured and modelled water content was most promising for leaves and ears in case of wheat, reaching coefficients of determination (R2) up to 0.72 and relative RMSE (rRMSE) of 26% and in case of corn for the leaf fraction only (R2 = 0.86, rRMSE = 23%). These findings indicate that, depending on the crop type and its structure, different parts of the canopy are observed by optical sensors. The results from the Munich-North-Isar test sites indicated that plant compartment specific EWTcanopy allows us to deduce more information about the physical meaning of model results than from equivalent water thickness on leaf level (EWT) which is upscaled to canopy water content (CWC) by multiplication of the leaf area index (LAI). Therefore, it is suggested to collect EWTcanopy data and corresponding reflectance for different crop types over the entire growing cycle. Nevertheless, the calibrated model proved to be transferable in time and space and thus can be applied for fast and effective retrieval of EWTcanopy in the scope of future hyperspectral satellite missions.

scholarly journals A representation of the phosphorus cycle for ORCHIDEE (revision 3985)

2017 ◽  
Author(s):  
Daniel S. Goll ◽  
Nicolas Vuichard ◽  
Fabienne Maignan ◽  
Albert Jornet-Puig ◽  
Jordi Sardans ◽  
...  
Keyword(s):  
Primary Productivity ◽  
Land Surface ◽  
Net Primary Productivity ◽  
Nutrient Content ◽  
Soil Development ◽  
Nutrient Concentrations ◽  
Surface Model ◽  
Phosphorus Cycle ◽  
Area Index ◽  
Leaf Level

Abstract. Land surface models rarely incorporate the terrestrial phosphorus cycle and its interactions with the carbon cycle, despite the extensive scientific debate about the importance of nitrogen and phosphorus supply for future land carbon uptake. We describe a representation of the terrestrial phosphorus cycle for the land surface model ORCHIDEE, and evaluate it with data from nutrient manipulation experiments along a soil formation chronosequence in Hawaii. ORCHIDEE accounts for influence of nutritional state of vegetation on tissue nutrient concentrations, photosynthesis, plant growth, biomass allocation, biochemical (phosphatase-mediated) mineralization and biological nitrogen fixation. Changes in nutrient content (quality) of litter affect the carbon use efficiency of decomposition and in return the nutrient availability to vegetation. The model explicitly accounts for root zone depletion of phosphorus as a function of root phosphorus uptake and phosphorus transport from soil to the root surface. The model captures the observed differences in the foliage stoichiometry of vegetation between an early (300yr) and a late stage (4.1 Myr) of soil development. The contrasting sensitivities of net primary productivity to the addition of either nitrogen, phosphorus or both among sites are in general reproduced by the model. As observed, the model simulates a preferential stimulation of leaf level productivity when nitrogen stress is alleviated, while leaf level productivity and leaf area index are stimulated equally when phosphorus stress is alleviated. The nutrient use efficiencies in the model are lower as observed primarily due to biases in the nutrient content and turnover of woody biomass. We conclude that ORCHIDEE is able to reproduce the shift from nitrogen to phosphorus limited net primary productivity along the soil development chronosequence, as well as the contrasting responses of net primary productivity to nutrient addition.

Modeling of a forested study site with the Community Land Model version 5 using climate projections for the 21st century.

2020 ◽  
Author(s):  
Lukas Strebel ◽  
Klaus Goergen ◽  
Bibi S. Naz ◽  
Heye Bogena ◽  
Harry Vereecken ◽  
...  
Keyword(s):  
Data Assimilation ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Land Surface ◽  
Model Parameters ◽  
Climate Projections ◽  
Modeling Framework ◽  
Area Index ◽  
Community Land Model

<p>Modeling forest ecosystems is important to facilitate adaptations in forest management approaches necessary to address the challenges of climate change, particularly of interest are ecohydrological states and fluxes such as soil water content, biomass, leaf area index, and evapotranspiration.</p><p>The community land model in its current version 5 (CLM5) simulates a broad collection of important land-surface processes; from moisture and energy partitioning, through biogeophysical processes, to surface and subsurface runoff. Additionally, CLM5 contains a biogeochemistry model (CLM5-BGC) which includes prognostic computation of vegetation states and carbon and nitrogen pools. However, CLM5 predictions are affected by uncertainty related to uncertain model forcings and parameters. Here, we use data assimilation methods to improve model performance by assimilating soil water content observations into CLM5 using the parallel data assimilation framework (PDAF).</p><p> </p><p>The coupled modeling framework was applied to the small (38.5 ha) forested catchment Wüstebach located in the Eifel National Park near the German-Belgian border. As part of the terrestrial environmental observatories (TERENO) network, the SoilNet sensors at the study site provide soil water content and soil temperature measurements since 2009.</p><p>CLM5 simulations for the period 2009-2100 were made, using local atmospheric observations for the period of 2009-2018 and an ensemble of regional climate model projections for 2019-2100. Simulations illustrate that data assimilation of soil water content improves the characterization of past model states, and that estimated model parameters and default model parameters result in different trajectories of ecohydrological states for 2019-2100. The simulations also illustrate that this site is hardly affected by increased water stress in the future.</p><p>The developed framework will be extended and applied for both ecosystem reanalysis as well as further simulations using climate projections across forested sites over Europe.</p>

scholarly journals Biophysical impacts of Earth greening largely controlled by aerodynamic resistance

2020 ◽  
Vol 6 (47) ◽  
pp. eabb1981
Author(s):  
Chi Chen ◽  
Dan Li ◽  
Yue Li ◽  
Shilong Piao ◽  
Xuhui Wang ◽  
...  
Keyword(s):  
Land Surface ◽  
Aerodynamic Resistance ◽  
Turbulent Heat Transfer ◽  
Dominant Factor ◽  
Turbulent Heat ◽  
Area Index ◽  
The Earth ◽  
Physically Based ◽  
Annual Scale ◽  
Increasing Trends

Satellite observations show widespread increasing trends of leaf area index (LAI), known as the Earth greening. However, the biophysical impacts of this greening on land surface temperature (LST) remain unclear. Here, we quantify the biophysical impacts of Earth greening on LST from 2000 to 2014 and disentangle the contributions of different factors using a physically based attribution model. We find that 93% of the global vegetated area shows negative sensitivity of LST to LAI increase at the annual scale, especially for semiarid woody vegetation. Further considering the LAI trends (P ≤ 0.1), 30% of the global vegetated area is cooled by these trends and 5% is warmed. Aerodynamic resistance is the dominant factor in controlling Earth greening’s biophysical impacts: The increase in LAI produces a decrease in aerodynamic resistance, thereby favoring increased turbulent heat transfer between the land and the atmosphere, especially latent heat flux.

scholarly journals A representation of the phosphorus cycle for ORCHIDEE (revision 4520)

2017 ◽  
Vol 10 (10) ◽  
pp. 3745-3770 ◽  
Author(s):  
Daniel S. Goll ◽  
Nicolas Vuichard ◽  
Fabienne Maignan ◽  
Albert Jornet-Puig ◽  
Jordi Sardans ◽  
...  
Keyword(s):  
Primary Productivity ◽  
Land Surface ◽  
Net Primary Productivity ◽  
Nutrient Content ◽  
Soil Development ◽  
Nutrient Concentrations ◽  
Surface Model ◽  
Phosphorus Cycle ◽  
Area Index ◽  
Leaf Level

Abstract. Land surface models rarely incorporate the terrestrial phosphorus cycle and its interactions with the carbon cycle, despite the extensive scientific debate about the importance of nitrogen and phosphorus supply for future land carbon uptake. We describe a representation of the terrestrial phosphorus cycle for the ORCHIDEE land surface model, and evaluate it with data from nutrient manipulation experiments along a soil formation chronosequence in Hawaii. ORCHIDEE accounts for the influence of the nutritional state of vegetation on tissue nutrient concentrations, photosynthesis, plant growth, biomass allocation, biochemical (phosphatase-mediated) mineralization, and biological nitrogen fixation. Changes in the nutrient content (quality) of litter affect the carbon use efficiency of decomposition and in return the nutrient availability to vegetation. The model explicitly accounts for root zone depletion of phosphorus as a function of root phosphorus uptake and phosphorus transport from the soil to the root surface. The model captures the observed differences in the foliage stoichiometry of vegetation between an early (300-year) and a late (4.1 Myr) stage of soil development. The contrasting sensitivities of net primary productivity to the addition of either nitrogen, phosphorus, or both among sites are in general reproduced by the model. As observed, the model simulates a preferential stimulation of leaf level productivity when nitrogen stress is alleviated, while leaf level productivity and leaf area index are stimulated equally when phosphorus stress is alleviated. The nutrient use efficiencies in the model are lower than observed primarily due to biases in the nutrient content and turnover of woody biomass. We conclude that ORCHIDEE is able to reproduce the shift from nitrogen to phosphorus limited net primary productivity along the soil development chronosequence, as well as the contrasting responses of net primary productivity to nutrient addition.

scholarly journals Contribution of woody elements to tree level reflectance in boreal forests

Silva Fennica ◽  
2021 ◽  
Vol 55 (5) ◽  
Author(s):  
Nea Kuusinen ◽  
Aarne Hovi ◽  
Miina Rautiainen
Keyword(s):  
Norway Spruce ◽  
Scots Pine ◽  
Forest Floor ◽  
Laser Scanning ◽  
Remote Sensing Data ◽  
Hyperspectral Data ◽  
Tree Level ◽  
Area Index ◽  
Reflectance Model ◽  
Physically Based

Spectral mixture analysis was used to estimate the contribution of woody elements to tree level reflectance from airborne hyperspectral data in boreal forest stands in Finland. Knowledge of the contribution of woody elements to tree or forest reflectance is important in the context of lea area index (LAI) estimation and, e.g., in the estimation of defoliation due to insect outbreaks, from remote sensing data. Field measurements from four Scots pine ( L.), five Norway spruce ( (L.) Karst.) and four birch ( Roth and Ehrh.) dominated plots, spectral measurements of needles, leaves, bark, and forest floor, airborne hyperspectral as well as airborne laser scanning data were used together with a physically-based forest reflectance model. We compared the results based on simple linear combinations of measured bark and needle/leaf spectra to those obtained by accounting for multiple scattering of radiation within the canopy using a physically-based forest reflectance model. The contribution of forest floor to reflectance was additionally considered. The resulted mean woody element contribution estimates varied from 0.140 to 0.186 for Scots pine, from 0.116 to 0.196 for birches and from 0.090 to 0.095 for Norway spruce, depending on the model used. The contribution of woody elements to tree reflectance had a weak connection to plot level forest variables.Pinus sylvestrisPicea abiesBetula pendulaBetula pubescens

scholarly journals Seasonal variation in grass water content estimated from proximal sensing and MODIS time series in a Mediterranean Fluxnet site

2015 ◽  
Vol 12 (18) ◽  
pp. 5523-5535 ◽  
Author(s):  
G. Mendiguren ◽  
M. Pilar Martín ◽  
H. Nieto ◽  
J. Pacheco-Labrador ◽  
S. Jurdao
Keyword(s):  
Seasonal Variation ◽  
Radiative Transfer ◽  
Water Content ◽  
Spectral Response ◽  
Empirical Models ◽  
Transfer Model ◽  
Proximal Sensing ◽  
Area Index ◽  
Equivalent Water Thickness ◽  
Monitoring Index

Abstract. This study evaluates three different metrics of water content of an herbaceous cover in a Mediterranean wooded grassland (dehesa) ecosystem. Fuel moisture content (FMC), equivalent water thickness (EWT) and canopy water content (CWC) were estimated from proximal sensing and MODIS satellite imagery. Dry matter (Dm) and leaf area index (LAI) connect the three metrics and were also analyzed. Metrics were derived from field sampling of grass cover within a 500 m MODIS pixel. Hand-held hyperspectral measurements and MODIS images were simultaneously acquired and predictive empirical models were parametrized. Two methods of estimating FMC and CWC using different field protocols were tested in order to evaluate the consistency of the metrics and the relationships with the predictive empirical models. In addition, radiative transfer models (RTM) were used to produce estimates of CWC and FMC, which were compared with the empirical ones. Results revealed that, for all metrics spatial variability was significantly lower than temporal. Thus we concluded that experimental design should prioritize sampling frequency rather than sample size. Dm variability was high which demonstrates that a constant annual Dm value should not be used to predict EWT from FMC as other previous studies did. Relative root mean square error (RRMSE) evaluated the performance of nine spectral indices to compute each variable. Visible Atmospherically Resistant Index (VARI) provided the lowest explicative power in all cases. For proximal sensing, Global Environment Monitoring Index (GEMI) showed higher statistical relationships both for FMC (RRMSE = 34.5 %) and EWT (RRMSE = 27.43 %) while Normalized Difference Infrared Index (NDII) and Global Vegetation Monitoring Index (GVMI) for CWC (RRMSE = 30.27 % and 31.58 % respectively). When MODIS data were used, results showed an increase in R2 and Enhanced Vegetation Index (EVI) as the best predictor for FMC (RRMSE = 33.81 %) and CWC (RRMSE = 27.56 %) and GEMI for EWT (RRMSE = 24.6 %). Differences in the viewing geometry of the platforms can explain these differences as the portion of vegetation observed by MODIS is larger than when using proximal sensing including the spectral response from scattered trees and its shadows. CWC was better predicted than the other two water content metrics, probably because CWC depends on LAI, that shows a notable seasonal variation in this ecosystem. Strong statistical relationship was found between empirical models using indices sensible to chlorophyll activity (NDVI or EVI which are not directly related to water content) due to the close relationship between LAI, water content and chlorophyll activity in grassland cover, which is not true for other types of vegetation such as forest or shrubs. The empirical methods tested outperformed FMC and CWC products based on radiative transfer model inversion.

scholarly journals Bi-Hemispherical Canopy Reflectance Model with Surface Heterogeneity Effects for the Estimation of LAI and fAPAR from MODIS White-Sky Spectral Albedo Data

2021 ◽  
Vol 13 (10) ◽  
pp. 1976
Author(s):  
Wouter Verhoef
Keyword(s):  
Optical Properties ◽  
Material Properties ◽  
Land Surface ◽  
Spatial Coherence ◽  
Surface Heterogeneity ◽  
Leaf Angle ◽  
Canopy Reflectance ◽  
Angle Distribution ◽  
Area Index ◽  
Leaf Canopy

Bi-hemispherical reflectance (BHR), in the land surface research community also known as “white-sky albedo”, is independent of the directions of incidence and viewing. For vegetation canopies, it is also nearly independent of the leaf angle distribution, and therefore it can be considered an optical quantity that is only dependent on material properties. For the combination leaf canopy and soil background, the most influential material properties are the canopy LAI (leaf area index), optical properties of the leaves, and soil brightness. When the leaf and soil optical properties are known or assumed, one may estimate the canopy LAI from its white-sky spectral albedo. This is also because a simple two-stream radiative transfer (RT) model is available for the BHR of the leaf canopy and soil combination. In this contribution, crown clumping and lateral linear mixing effects are incorporated in this model. A new procedure to estimate soil brightness is introduced here, even under a moderate layer of green vegetation. The procedure uses the red and NIR spectral bands. A MODIS white-sky albedo product at a spatial resolution of 0.05° is used as a sample input to derive global maps of LAI, soil brightness, and fAPAR at the local moments of minimum and maximum NDVI over a 20-year period. These maps show a high degree of spatial coherence and demonstrate the possible utility of products that can be generated with little effort by using a direct LUT technique.

scholarly journals Relationship between Vegetation Biophysical Properties and Surface Temperature Using Multisensor Satellite Data

2007 ◽  
Vol 20 (22) ◽  
pp. 5593-5606 ◽  
Author(s):  
Seungbum Hong ◽  
Venkat Lakshmi ◽  
Eric E. Small
Keyword(s):  
Surface Temperature ◽  
Water Content ◽  
Land Surface ◽  
Vegetation Index ◽  
Climatic Variability ◽  
Regional Distribution ◽  
Spatial And Temporal Variability ◽  
Area Index ◽  
Vegetation Water Content ◽  
Vegetation Water

Abstract Vegetation is an important factor in global climatic variability and plays a key role in the complex interactions between the land surface and the atmosphere. This study focuses on the spatial and temporal variability of vegetation and its relationship with land–atmosphere interactions. The authors have analyzed the vegetation water content (VegWC) from the Advanced Microwave Scanning Radiometer for EOS (AMSR-E), the leaf area index (LAI), the normalized difference vegetation index (NDVI), the land surface temperature (Ts), and the Moderate Resolution Imaging Spectroradiometer (MODIS). Three regions, which have climatically differing characteristics, have been selected: the North America Monsoon System (NAMS) region, the Southern Great Plains (SGP) region, and the Little River Watershed in Tifton, Georgia. Temporal analyses were performed by comparing satellite observations from 2003 and 2004. The introduction of the normalized vegetation water content (NVegWC) derived as the ratio of VegWC and LAI corresponding to the amount of water in individual leaves has been estimated and this yields significant correlation with NDVI and Ts. The analysis of the NVegWC–NDVI relationship in the above listed three regions displays a negative exponential relation, and the Ts–NDVI relationship (TvX relationship) is inversely proportional. The correlation between these variables is higher in arid areas such as the NAMS region, and becomes less correlated in the more humid and more vegetated regions such as the area of eastern Georgia. A land-cover map is used to examine the influence of vegetation types on the vegetation biophysical and surface temperature relationships. The regional distribution of vegetation reflects the relationship between the vegetation biological characteristics of water and the growing environment.

scholarly journals Seasonal variation in vegetation water content estimated from proximal sensing and MODIS time series in a Mediterranean Fluxnet site

2015 ◽  
Vol 12 (7) ◽  
pp. 5503-5533
Author(s):  
G. Mendiguren ◽  
M. P. Martín ◽  
H. Nieto ◽  
J. Pacheco-Labrador ◽  
S. Jurdao
Keyword(s):  
Spatial Variation ◽  
Water Content ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Spectral Indices ◽  
Proximal Sensing ◽  
Area Index ◽  
Vegetation Water Content ◽  
Equivalent Water Thickness ◽  
Vegetation Water

Abstract. This study evaluates three different metrics of vegetation water content estimated from proximal sensing and MODIS satellite imagery: Fuel Moisture Content (FMC), Equivalent Water Thickness (EWT) and Canopy Water Content (CWC). Dry matter (Dm) and Leaf area Index (LAI) were also analyzed in order to connect FMC with EWT and EWT with CWC, respectively. This research took place in a Fluxnet site located in Mediterranean wooded grassland (dehesa) ecosystem in Las Majadas del Tietar (Spain). Results indicated that FMC and EWT showed lower spatial variation than CWC. The spatial variation within the MODIS pixel was not as critical as its temporal trend, so to capture better the variability, fewer plots should be sampled but more times. Due to the high seasonal Dm variability, a constant annual value would not work to predict EWT from FMC. Relative root mean square error (RRMSE) evaluated the performance of nine spectral indices to compute each variable. VARI provided the worst results in all cases. For proximal sensing, GEMI worked best for both FMC (RRMSE = 34.5%) and EWT (RRMSE = 27.43%) while NDII and GVMI performed best for CWC (RRMSE =30.27% and 31.58% respectively). For MODIS data, results were a bit better with EVI as the best predictor for FMC (RRMSE = 33.81%) and CWC (RRMSE = 27.56%) and GEMI for EWT (RRMSE = 24.6%). To explain these differences, proximal sensing measures only grasslands at nadir view angle, but MODIS includes also trees, their shades, and other artifacts at up to 20° view angle. CWC was better predicted than the other two water content variables, probably because CWC depends on LAI, which is highly correlated to the spectral indices. Finally, these empirical methods outperformed FMC and CWC products based on radiative transfer model inversion.

Sign in / Sign up

Export Citation Format

Share Document