scholarly journals Modeling, Simulation, Experimentation, and Compensation of Temperature Effect in Impedance-Based SHM Systems Applied to Steel Pipes

Sensors ◽  
2019 ◽  
Vol 19 (12) ◽  
pp. 2802 ◽  
Author(s):  
Rothschild A. Antunes ◽  
Nicolás E. Cortez ◽  
Bárbara M. Gianesini ◽  
Jozue Vieira Filho
Keyword(s):  
Temperature Effect ◽  
Petroleum Industry ◽  
Experimental Results ◽  
Temperature Changes ◽  
Steel Pipes ◽  
Electromechanical Impedance ◽  
Wide Range ◽  
Impedance Technique ◽  
Complete Study ◽  
Chemical Products

Pipelines have been widely used for the transportation of chemical products, mainly those related to the petroleum industry. Damage in such pipelines can produce leakage with unpredictable consequences to the environment. There are different structural health monitoring (SHM) systems such as Lamb wave, comparative vacuum, acoustic emission, etc. for monitoring such structures. However, those based on piezoelectric sensors and electromechanical impedance technique (EMI) measurements are simple and efficient, and have been applied in a wide range of structures, including pipes. A disadvantage of such technique is that temperature changes can lead to false diagnoses. To overcome this disadvantage, temperature variation compensation techniques are normally incorporated. Therefore, this work has developed a complete study applied to damage detection in pipelines, including an innovative technique for compensating the temperature effect in EMI-based SHM and the modeling of piezoceramics bonded to pipeline structures using finite elements. Experimental results were used to validate the model. Moreover, the compensation method was tested in two steel pipes—healthy and damaged—compensating the temperature effect ranging from −40 °C to +80 °C, with analysis on the frequency range from 5 kHz to 120 kHz. The simulated and experimental results showed that the studies effectively contribute to the SHM area, mainly to EMI-based techniques.

Method for removing temperature effect in impedance-based structural health monitoring systems using polynomial regression

2020 ◽  
pp. 147592172091712 ◽  
Author(s):  
Bárbara M Gianesini ◽  
Nicolás E Cortez ◽  
Rothschild A Antunes ◽  
Jozue Vieira Filho
Keyword(s):  
Structural Health Monitoring ◽  
Damage Detection ◽  
Temperature Effect ◽  
Health Monitoring ◽  
Monitoring Systems ◽  
Electromechanical Impedance ◽  
Structural Health ◽  
Detection Systems ◽  
Impedance Technique ◽  
Health Monitoring Systems

Structural health monitoring systems are employed to evaluate the state of structures to detect damage, bringing economical and safety benefits. The electromechanical impedance technique is a promising damage detection tool since it evaluates structural integrity by only measuring the electrical impedance of piezoelectric transducers bonded to structures. However, in real-world applications, impedance-based damage detection systems exhibit strong temperature dependence; therefore, variations associated with temperature changes may be confused as damage. In this article, the temperature effect on the electrical impedance of piezoelectric ceramics attached to structures is analyzed. Besides, a new methodology to compensate for the temperature effect in the electromechanical impedance technique is proposed. The method is very general since it can be applied to nonlinear (polynomial) temperature and/or frequency dependences observed on the horizontal and vertical shifts of the impedance signatures. A computer algorithm that performs the compensation was developed, which can be easily incorporated into real-time damage detection systems. This compensation technique is applied successfully to two aluminum beams and one steel pipe, minimizing the effect of temperature variations on damage detection structural health monitoring systems in the temperature range from −40°C to 80°C and the frequency range from 10 to 90 kHz.

Monitoring of concrete curing using the electromechanical impedance technique: review and path forward

2019 ◽  
pp. 147592171989306 ◽  
Author(s):  
Yee Yan Lim ◽  
Scott T Smith ◽  
Ricardo Vasquez Padilla ◽  
Chee Kiong Soh
Keyword(s):  
State Of The Art ◽  
Research Field ◽  
Strength Development ◽  
Early Age ◽  
Remote Monitoring System ◽  
Electromechanical Impedance ◽  
Wide Range ◽  
Impedance Technique ◽  
Technology Modeling ◽  
Early Age Concrete

The ability to monitor the strength development of early-age concrete is an important capability in the laboratory and in the field. Accurate and reliable in situ measurements can inform the appropriate time for removal of formwork and loading of structural elements, as well as determination of batch quality. The piezoelectric-based electromechanical impedance technique is emerging as a viable option for such monitoring needs. The first research articles on the topic started to appear in 2005, and since then, the research field has advanced and has grown in popularity. This article therefore presents the first state-of-the-art review of the topic to date. In this article, existing research is reviewed and sorted into key themes while critical developments as well as knowledge gaps are identified. The topics addressed range from miniaturization of hardware, methods of installation, incorporation of wireless technology, modeling, data interpretation, signal processing, influence of curing, and environmental conditions to a wide range of other practical issues. Previous studies have indicated that the electromechanical impedance technique has the potential to be developed into an autonomous and remote monitoring system, capable of predicting the strength development of early-age concrete structures in real time. An end game is therefore the realization of this capability. Appropriate comments are therefore also provided in this article about this goal. Researchers interested in venturing into this research area shall find this article a useful introduction as well as a state-of-the-art assessment. In addition, the identified research gaps can inform projects for more experienced research teams.

Removal of temperature effect in impedance-based damage detection using the cointegration method

2019 ◽  
Vol 30 (15) ◽  
pp. 2189-2197 ◽  
Author(s):  
Xiujuan Li ◽  
Wenzhong Qu ◽  
Li Xiao ◽  
Ye Lu
Keyword(s):  
Damage Detection ◽  
Temperature Effect ◽  
Environmental Temperature ◽  
Peak Frequency ◽  
Steel Plates ◽  
Practical Application ◽  
New Approach ◽  
Electromechanical Impedance ◽  
Augmented Dickey Fuller ◽  
Impedance Technique

Electromechanical impedance technique has been widely used in the area of structural health monitoring. However, both damage and variation in environmental temperature can cause the changes in electromechanical impedance signature, which may cause false damage diagnosis. The temperature effect on the electromechanical impedance-based method has been one of its main drawbacks in practical application. This article proposes a new approach based on cointegration to eliminate temperature interference in the electromechanical impedance technique. The augmented Dickey–Fuller test is used to analyze the stationary characteristics of the time series and determine the degree of non-stationarity. The Johansen test is used to obtain the cointegrating residuals instead of the direct electromechanical impedance responses for damage detection. The proposed method is verified on the undamaged and damaged steel plates with the consideration of environmental temperature variations. The damage detection was based on the electromechanical impedance technique in which the peak frequency is chosen as a cointegrated variable. The experimental results show that the cointegration method can remove the temperature effect on the electromechanical impedance responses, and the cointegrating residuals are effective indices to indicate the occurrence of damage.

A PZT-based electromechanical impedance method for monitoring the moisture content of wood

Sensor Review ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Quan Zhai ◽  
Jicheng Zhang ◽  
Guofeng Du ◽  
Yulong Rao ◽  
Xiaoyu Liu
Keyword(s):  
Moisture Content ◽  
Mechanical Impedance ◽  
Impedance Method ◽  
Impedance Change ◽  
Monitoring Method ◽  
Content Type ◽  
Electromechanical Impedance ◽  
Wide Range ◽  
Impedance Technique ◽  
Piezoelectric Impedance

Purpose At present, piezoelectric impedance technology has been used in the study of wood damage monitoring. However, little effort has been made in the research on the application of piezoelectric impedance system to monitor the change of wood moisture content (MC). The monitoring method of wood MC is used by piezoelectric impedance technique in this study. Design/methodology/approach One piezoceramic transducer is bonded to the surface of wood specimens. The MC of the wood specimens increases gradually from 0% to 60% with 10% increments; the mechanical impedance of the wood specimen will change, and the change in the mechanical impedance of the structure is reflected by monitoring the change in the electrical impedance of lead zirconate titanate. Therefore, this paper investigates the relationship between wood MC change and piezoelectric impedance change to verify the feasibility of the piezoelectric impedance method for monitoring wood MC change. Findings The experiment verified that the real part of impedance of the wood increased with the increase of wood MC. Besides, the damage index root mean square deviation is introduced to quantify the damage degree of wood under different MC. At the same time, the feasibility and validity of this experiment were verified from the side by finite element simulation. Finally, MC monitoring by piezoelectric impedance technique is feasible. Originality/value To the best of the authors’ knowledge, this work is the first to apply piezoelectric ceramics to the monitoring of wood MC, which provides a theoretical basis for the follow-up study of a wide range of wood components and even wood structure MC changes.

On the nominal transverse shear strain to characterize the severity of creasing

TAPPI Journal ◽  
2018 ◽  
Vol 17 (04) ◽  
pp. 231-240
Author(s):  
Douglas Coffin ◽  
Joel Panek
Keyword(s):  
Shear Strain ◽  
Transverse Shear ◽  
Elastic Limit ◽  
Experimental Results ◽  
Transverse Shear Strain ◽  
Maximum Strain ◽  
Machine Direction ◽  
Engineering Approach ◽  
Wide Range ◽  
Analytic Expression

A transverse shear strain was utilized to characterize the severity of creasing for a wide range of tooling configurations. An analytic expression of transverse shear strain, which accounts for tooling geometry, correlated well with relative crease strength and springback as determined from 90° fold tests. The experimental results show a minimum strain (elastic limit) that needs to be exceeded for the relative crease strength to be reduced. The theory predicts a maximum achievable transverse shear strain, which is further limited if the tooling clearance is negative. The elastic limit and maximum strain thus describe the range of interest for effective creasing. In this range, cross direction (CD)-creased samples were more sensitive to creasing than machine direction (MD)-creased samples, but the differences were reduced as the shear strain approached the maximum. The presented development provides the foundation for a quantitative engineering approach to creasing and folding operations.

scholarly journals LED Rail Signals: Full Hardware Realization of Apparatus with Independent Intensity by Temperature Changes

Electronics ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1291
Author(s):  
Giuseppe Schirripa Schirripa Spagnolo ◽  
Fabio Leccese
Keyword(s):  
Temperature Sensor ◽  
Energy Efficient ◽  
Light Emitting Diode ◽  
Junction Temperature ◽  
Light Emitting ◽  
Temperature Changes ◽  
Wide Range ◽  
International Regulations ◽  
Long Lifetime ◽  
Set Up

Nowadays, signal lights are made using light-emitting diode arrays (LEDs). These devices are extremely energy efficient and have a very long lifetime. Unfortunately, especially for yellow/amber LEDs, the intensity of the light is closely related to the junction temperature. This makes it difficult to design signal lights to be used in naval, road, railway, and aeronautical sectors, capable of fully respecting national and international regulations. Furthermore, the limitations prescribed by the standards must be respected in a wide range of temperature variations. In other words, in the signaling apparatuses, a system that varies the light intensity emitted according to the operating temperature is useful/necessary. In this paper, we propose a simple and effective solution. In order to adjust the intensity of the light emitted by the LEDs, we use an LED identical to those used to emit light as a temperature sensor. The proposed system was created and tested in the laboratory. As the same device as the ones to be controlled is used as the temperature sensor, the system is very stable and easy to set up.

scholarly journals Numerical Phase-Field Model Validation for Dissolution of Minerals

2021 ◽  
Vol 11 (6) ◽  
pp. 2464
Author(s):  
Sha Yang ◽  
Neven Ukrainczyk ◽  
Antonio Caggiano ◽  
Eddie Koenders
Keyword(s):  
Phase Field ◽  
Liquid Interface ◽  
Mineral Dissolution ◽  
Experimental Results ◽  
Wide Range ◽  
Congruent Dissolution ◽  
Solid Liquid Interface ◽  
Solid Liquid ◽  
Dissolution Of Minerals ◽  
Meso Scale

Modelling of a mineral dissolution front propagation is of interest in a wide range of scientific and engineering fields. The dissolution of minerals often involves complex physico-chemical processes at the solid–liquid interface (at nano-scale), which at the micro-to-meso-scale can be simplified to the problem of continuously moving boundaries. In this work, we studied the diffusion-controlled congruent dissolution of minerals from a meso-scale phase transition perspective. The dynamic evolution of the solid–liquid interface, during the dissolution process, is numerically simulated by employing the Finite Element Method (FEM) and using the phase–field (PF) approach, the latter implemented in the open-source Multiphysics Object Oriented Simulation Environment (MOOSE). The parameterization of the PF numerical approach is discussed in detail and validated against the experimental results for a congruent dissolution case of NaCl (taken from literature) as well as on analytical models for simple geometries. In addition, the effect of the shape of a dissolving mineral particle was analysed, thus demonstrating that the PF approach is suitable for simulating the mesoscopic morphological evolution of arbitrary geometries. Finally, the comparison of the PF method with experimental results demonstrated the importance of the dissolution rate mechanisms, which can be controlled by the interface reaction rate or by the diffusive transport mechanism.

scholarly journals Sustainable Myrcene-Based Elastomers via a Convenient Anionic Polymerization

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 838
Author(s):  
David Hermann Lamparelli ◽  
Magdalena Maria Kleybolte ◽  
Malte Winnacker ◽  
Carmine Capacchione
Keyword(s):  
Anionic Polymerization ◽  
Sodium Hydride ◽  
Reactivity Ratios ◽  
Molecular Weights ◽  
Styrene Copolymers ◽  
Wide Range ◽  
Elastomeric Materials ◽  
Complete Study ◽  
Anionic Copolymerization ◽  
Trialkylaluminum Derivatives

Soluble heterocomplexes consisting of sodium hydride in combination with trialkylaluminum derivatives have been used as anionic initiating systems at 100 °C in toluene for convenient homo-, co- and ter-polymerization of myrcene with styrene and isoprene. In this way it has been possible to obtain elastomeric materials in a wide range of compositions with interesting thermal profiles and different polymeric architectures by simply modulating the alimentation feed and the (monomers)/(initiator systems) ratio. Especially, a complete study of the myrcene-styrene copolymers (PMS) was carried out, highlighting their tapered microstructures with high molecular weights (up to 159.8 KDa) and a single glass transition temperature. For PMS copolymer reactivity ratios, rmyr = 0.12 ± 0.003 and rsty = 3.18 ± 0.65 and rmyr = 0.10 ± 0.004 and rsty = 3.32 ± 0.68 were determined according to the Kelen–Tudos (KT) and extended Kelen–Tudos (exKT) methods, respectively. Finally, this study showed an easy accessible approach for the production of various elastomers by anionic copolymerization of renewable terpenes, such as myrcene, with commodities.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

Sign in / Sign up

Export Citation Format

Share Document