scholarly journals Synthesis and Characterization of B/NaF and Silicon Phthalocyanine-Modified TiO2 and an Evaluation of Their Photocatalytic Removal of Carbamazepine

Separations ◽  
2020 ◽  
Vol 7 (4) ◽  
pp. 71
Author(s):  
Chukwuka B. Anucha ◽  
IIknur Altin ◽  
Debora Fabbri ◽  
Ismail Degirmencioglu ◽  
Paola Calza ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Total Pore Volume ◽  
Pure Tio2 ◽  
Complete Disappearance ◽  
Visible Absorption ◽  
X Ray ◽  
Transmission Electron ◽  
Bet Analysis ◽  
Silicon Based ◽  
Adsorption Desorption

This study investigated the synthesis of two different types of photocatalysts, namely, boron/sodium fluoride co-doped titanium dioxide (B/NaF-TiO2), and its analogue, a dye-sensitized form of silicon-based axial methoxy substituted phthalocyanine (B/NaF-TiO2SiPc). Structural and morphological characterizations were performed via X-ray diffraction (XRD); Fourier transform infra-red (FTIR); N2 adsorption–desorption at 77 K by Brunauer–Emmett–Teller (BET) and Barrett, Joyner, and Halenda (BJH) methods; transmission electron microscopy (TEM); X-ray photoelectron spectroscopy (XPS); and UV–visible absorption spectroscopy. The estimated crystallite size of pure TiO2 and pure B/NaF-TiO2 was 24 nm, and that of B/NaF-TiO2SiPc was 29 nm, whereas particle sizes determined by TEM were 25, 28, and 31 nm for pure TiO2, B/NaF-TiO2 and B/NaF-TiO2SiPc respectively. No significant differences between B/NaF-TiO2 and B/NaF-TiO2SiPc were observed for surface area by (BET) analysis (13 m2/g) or total pore volume by the BJH application model (0.05 cm3/g). Energy band gap values obtained for B/NaF-TiO2 and B/NaF-TiO2SiPc were 3.10 and 2.90 eV respectively, lower than pure TiO2 (3.17 eV). The photocatalytic activity of the synthesized materials was tested using carbamazepine (CBZ) as the model substrate. Carbamazepine removal after 4 h of irradiation was almost 100% for B/NaF-TiO2 and 70% for B/NaF-TiO2SiPc; however, the substrate mineralization proceeded slower, suggesting the presence of organic intermediates after the complete disappearance of the pollutant.

Low-temperature route to nanoscale P3N5 hollow spheres

2003 ◽  
Vol 18 (10) ◽  
pp. 2359-2363 ◽  
Author(s):  
Hongzhou Gu ◽  
Yunle Gu ◽  
Zhefeng Li ◽  
Yongcheng Ying ◽  
Yitai Qian
Keyword(s):  
Photoelectron Spectroscopy ◽  
Hollow Spheres ◽  
Molar Ratio ◽  
Visible Absorption ◽  
X Ray ◽  
Transmission Electron ◽  
Influence Of Temperature On ◽  
Wide Gap ◽  
20 Nm ◽  
High Degree

Nanoscale hollow spheres of amorphous phosphorus nitride (P3N5) were synthesized by reacting PCl3 with NaN3 at 150–250 °C. Transmission electron microscope images show that the hollow spheres have a diameter of 150–350 nm, and the thickness of the shell is 20 nm. A very small amount of curly films were also found in the sample prepared at 150 °C. The infrared spectrum indicates a high degree of purity. X-ray photoelectron spectroscopy indicates the presence of P and N, with a molar ratio of 1:1.62 for P:N. Ultraviolet-visible absorption spectroscopy shows an absorption band at 265–315 nm. Under photoluminescent excitation at 230 nm, the P3N5 emits ultraviolet light at 305 nm. With a band gap of 4.28 eV, the products may be a wide gap semiconductor. A possible mechanism and the influence of temperature on the formation of the hollow spheres are also discussed.

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

2021 ◽  
Vol 11 (5) ◽  
pp. 706-716
Author(s):  
Nada D. Al-Khthami ◽  
Tariq Altalhi ◽  
Mohammed Alsawat ◽  
Mohamed S. Amin ◽  
Yousef G. Alghamdi ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Bandgap Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Structural Surface ◽  
Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

A Facile Strategy to Fabricate Nanoscale Zero-Valent Iron Decorated Graphene Oxide Composite for Dechloridation of Trichloroacetic Acid in Water

2018 ◽  
Vol 18 (12) ◽  
pp. 8252-8257 ◽  
Author(s):  
Huixuan Zhang ◽  
Xinyi Zhang ◽  
Ruonan Guo ◽  
Qingfeng Cheng ◽  
Xiuwen Cheng
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Sewage Treatment ◽  
Reduction Process ◽  
Zero Valent Iron ◽  
Chlorinated Organic Compounds ◽  
X Ray ◽  
Transmission Electron ◽  
Nanoscale Zero Valent Iron ◽  
Adsorption Desorption

In this study, nanoscale zero-valent iron decorated graphene oxide (NZVI/GO) composite was fabricated through a reduction process in the presence of sodium borohydride (NaBH4) solution. Subsequently, physicochemical properties of the NZVI/GO composites were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transformation infrared spectroscopy (FT-IR) and Raman spectra. Results indicated that Fe species existed in the form of Fe0, which uniformly dispersed on the surface of GO. Furthermore, the performance of NZVI/GO was evaluated by the degradation of tichloroacetic acid (TCAA). TCAA can be rapidly degraded by NZVI/GO. This paper provides a promising strategy to synthesize versatile catalyst which would be potentially applied in sewage treatment to degrade chlorinated organic compounds.

scholarly journals Preparation, Characterization, and Performance Analysis of S-Doped Bi2MoO6 Nanosheets

Nanomaterials ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1341 ◽  
Author(s):  
Ruiqi Wang ◽  
Duanyang Li ◽  
Hailong Wang ◽  
Chenglun Liu ◽  
Longjun Xu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Degradation Rate ◽  
X Ray Diffraction ◽  
Photo Degradation ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
And Performance ◽  
Adsorption Desorption ◽  
Excellent Stability

S-doped Bi2MoO6 nanosheets were successfully synthesized by a simple hydrothermal method. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption–desorption isotherms, Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), elemental mapping spectroscopy, photoluminescence spectra (PL), X-ray photoelectron spectroscopy (XPS), and UV-visible diffused reflectance spectra (UV-vis DRS). The photo-electrochemical performance of the samples was investigated via an electrochemical workstation. The S-doped Bi2MoO6 nanosheets exhibited enhanced photocatalytic activity under visible light irradiation. The photo-degradation rate of Rhodamine B (RhB) by S-doped Bi2MoO6 (1 wt%) reached 97% after 60 min, which was higher than that of the pure Bi2MoO6 and other S-doped products. The degradation rate of the recovered S-doped Bi2MoO6 (1 wt%) was still nearly 90% in the third cycle, indicating an excellent stability of the catalyst. The radical-capture experiments confirmed that superoxide radicals (·O2−) and holes (h+) were the main active substances in the photocatalytic degradation of RhB by S-doped Bi2MoO6.

Facile Synthesis and Characterization of Spinel NiFe2O4 Nanoparticles and Studies of Their Photocatalytic Activity for Oxidation of Alcohols

2020 ◽  
Vol 12 (3) ◽  
pp. 357-365 ◽  
Author(s):  
Xiangrong Ma ◽  
Rui Dang ◽  
Jieying Liu ◽  
Fang Yang ◽  
Huigui Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Bet Analysis ◽  
Oxidation Of Alcohols ◽  
20 Nm ◽  
Adsorption Desorption

In this paper, we report a novel and facile approach for the synthesis of spinel NiFe2O4 nanoparticles and studies of its photocatalytic activity for oxidation of alcohols. The as-synthesized catalyst was thoroughly characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), elemental mapping, transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), and N2 adsorption–desorption isotherm (BET) analysis. The TEM image reveals cubic shapes with an average particle size of 10–20 nm. The as-synthesized spinel NiFe2O4 has proved to be an excellent photocatalyst for oxidation of alcohol to the aldehyde with a conversion of 80% and selectivity of 99%. The catalyst has also proved to be noteworthy as it does not loss its catalytic activity even after five cycles of reuse.

SYNTHESIS, CHARACTERIZATION AND THE APPLICABILITY OF β-CYCLODEXTRINS FUNCTIONALIZED MESOPOROUS SBA-15 MOLECULAR SIEVES

NANO ◽  
2013 ◽  
Vol 08 (05) ◽  
pp. 1350050
Author(s):  
MIN GUAN ◽  
HAI-PENG BI ◽  
ZUYUAN WANG ◽  
SHAOHUA BU ◽  
LING HUANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Molecular Sieves ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Capacities ◽  
Transmission Electron ◽  
Potential Applications ◽  
Adsorption Desorption

Mesoporous silicas SBA-15 are modified with β-Cyclodextrins (β-CD) by simple grafting method. β-CD functionalized SBA-15 was characterized by Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), powder X-ray diffraction (PXRD), nitrogen adsorption–desorption measurements, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). Furthermore, the applicability of it is investigated through studying the adsorption properties of clenbuterol. It showed better adsorption capacities of clenbuterol than pure SBA-15. β-CD functionalized SBA-15 material has the potential applications in the treatment of clenbuterol contamination in food and environment science.

scholarly journals A STUDY ON HYDROTHERMAL SYNTHESIS OF METAL–ORGANIC FRAMEWORK MIL-101

2017 ◽  
Vol 126 (1C) ◽  
pp. 21
Author(s):  
Võ Thị Thanh Châu ◽  
Hoàng Văn Đức
Keyword(s):  
Hydrothermal Synthesis ◽  
Photoelectron Spectroscopy ◽  
Metal Organic Framework ◽  
Hydrothermal Process ◽  
Nitrogen Adsorption ◽  
X Ray ◽  
Transmission Electron ◽  
Metal Organic ◽  
Adsorption Desorption ◽  
Organic Framework

<p>In the present paper, a synthesis of MIL-101 by hydrothermal process was demonstrated. The obtained samples were characterized by powder X-ray diffraction (PXRD), transmission electron microscope (TEM), nitrogen adsorption/desorption isotherms at 77K, X-ray photoelectron spectroscopy (XPS). The results showed that MIL-101 synthesized by optimal conditions exhibited high crystallinity and surface area. The obtained MIL-101 possesses high stability in water and several organic solvents.</p><p><strong>Keywords:</strong> MIL-101, hydrothermal synthesis, metal organic framework-101. </p>

scholarly journals Catalytic Activity of Mixed Al2O3-ZrO2 Oxides for Glucose Conversion into 5-Hydroxymethylfurfural

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 878 ◽  
Author(s):  
Benjamín Torres-Olea ◽  
Sandra Mérida-Morales ◽  
Cristina García-Sancho ◽  
Juan Antonio Cecilia ◽  
Pedro Maireles-Torres
Keyword(s):  
Catalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Molar Ratio ◽  
X Ray ◽  
Zirconium Oxides ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Secondary Reactions ◽  
Temperature Programmed ◽  
Adsorption Desorption

In the present work, a series of catalysts based on aluminum and zirconium oxides was studied for the transformation of glucose into 5-hydroxymethylfurfural. These catalysts were characterized by using experimental techniques, such as X-ray diffraction, N2 adsorption–desorption at −196 °C, X-ray photoelectron spectroscopy, temperature-programmed desorption of NH3 and CO2, and scanning transmission electron microscopy. The catalytic behavior in glucose dehydration was evaluated in a water-methyl isobutyl ketone biphasic system, in the presence of CaCl2, in order to minimize losses due to unwanted secondary reactions. High glucose conversion and 5-hydroxymethylfurfural (HMF) yield values were obtained in the presence of an Al(Zr)Ox catalyst with an Al:Zr molar ratio of 7:3, reaching 97% and 47%, respectively, at 150 °C after 120 min. Under tested conditions, this catalyst retained most of its catalytic activity for four reuses.

scholarly journals Novel Route to Obtain Carbon Self-Doped TiO2 Mesoporous Nanoparticles as Efficient Photocatalysts for Environmental Remediation Processes under Visible Light

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3349 ◽  
Author(s):  
Pablo A. Ochoa Rodríguez ◽  
Tamara B. Benzaquén ◽  
Gina A. Pecchi ◽  
Sandra G. Casuscelli ◽  
Verónica R. Elías ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Environmental Remediation ◽  
Synthesis Method ◽  
Mesoporous Structure ◽  
Acid Orange 7 ◽  
X Ray Diffraction ◽  
Visible Radiation ◽  
X Ray ◽  
Transmission Electron ◽  
Adsorption Desorption

Titanium dioxide materials were synthesized using two different methods. The samples were characterized by X-ray diffraction (XRD), UV–Visible diffusion reflectance spectroscopy (UV-Vis DR), Raman spectroscopy, N2 adsorption/desorption, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron spectroscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Although both kind of materials were found to have mesoporous structure and anatase crystalline phase, one of them was obtained from a synthesis method that does not involve the use of surfactants, and therefore, does not require calcination at high temperatures. This implies that the synthesized solid was self-doped with carbon species, coming only from the same source used for titanium. Then, the relationship between the presence of these species, the final calcination temperature, and the photocatalytic activity of the solids was studied in terms of the degradation and mineralization of an Acid Orange 7 aqueous solution, under visible radiation. A photosensitizing effect caused by the non-metal presence, that allows the solid to extend its absorption range, was found. Hence, a novel route to prepare C-modified photoactive mesoporous TiO2, simpler and cheaper, where neither a template nor an external carbon source is used, could be performed.

Pd/SiO2 Inorganic–Organic Composite Membrane Calcined Under N2 Atmosphere: Thermal Stability and H2/CO2 Separation

2019 ◽  
Vol 19 (6) ◽  
pp. 3210-3217
Author(s):  
Jing Yang ◽  
Wang-Qing Fan ◽  
Ruihua Mu ◽  
Yamei Zhao
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Total Pore Volume ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
N2 Atmosphere ◽  
Bet Specific Surface Area ◽  
The Mean

A novel Pd/SiO2 inorganic–organic composite material was developed for the selective separation of H2 from a mixture of H2 and CO2. Its thermal stability and microstructure calcined under N2 atmosphere were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy and N2 sorption–desorption measurements. Pd element in Pd/SiO2 gel material exists in PdCl2 form, calcination at 350 °C can result in the complete transformation of Pd2+ to metallic Pd0. With the increase of calcination temperature, the hydrophobic Si–CH3 bands decreased in intensity. The residue of Pd/SiO2 material calcined at 800 °C was mainly composed of Si–O–Si, metallic Pd0, CSi4 and some elemental C0. The mean pore size, BET specific surface area and total pore volume of the as-prepared Pd/SiO2 material calcined at 350 °C was about 2.26 nm, 417.35 m2 g−1 and 0.288 m3 g−1, respectively. The mean H2 and CO2 permeances of the corresponding Pd/SiO2 membrane were 9.90×10−6 and 9.10×10−7 mol m−2 Pa−1 s−1, respectively, when operating at 200 °C and a pressure difference of 0.3 MPa. After the steam exposure at 200 °C for 168 h, the H2 permeance decreased by 3.23% while the H2/CO2 permselectivity increased by 2.50%.

Sign in / Sign up

Export Citation Format

Share Document