scholarly journals Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+

2019 ◽  
Vol 11 (2) ◽  
pp. 554 ◽  
Author(s):  
Krzysztof Kosowski ◽  
Karol Tucki ◽  
Marian Piwowarski ◽  
Robert Stępień ◽  
Olga Orynycz ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
High Efficiency ◽  
Thermodynamic Cycle ◽  
Economic Resilience ◽  
Public Power ◽  
Pass System ◽  
Classical Gas ◽  
Gas Turbine Cycle

An analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with a regenerator can provide higher efficiency than a classical gas turbine cycle with a regenerator. The best arrangements of combined air–steam cycles achieved very high values for overall cycle efficiency—that is, higher than 60%. An increase in efficiency to such degree would decrease fuel consumption, contribute to the mitigation of carbon dioxide emissions, and strengthen the sustainability of the region served by the power plant. This increase in efficiency might also contribute to the economic resilience of the area.

scholarly journals Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry

2019 ◽  
Vol 11 (9) ◽  
pp. 2647 ◽  
Author(s):  
Krzysztof Kosowski ◽  
Karol Tucki ◽  
Marian Piwowarski ◽  
Robert Stępień ◽  
Olga Orynycz ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
High Efficiency ◽  
Thermodynamic Cycle ◽  
Innovative Technology ◽  
Pass System ◽  
Gaseous Fuels ◽  
Micro Power ◽  
Effective Heat Exchanger ◽  
Gas Turbine Cycle

An analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could have an efficiency higher than a classical gas turbine cycle with a regenerator. Appropriate cycle and turbine calculations were performed for micro power plants with turbine output in the range of 10–50 kW. The best arrangements achieved very high values of overall cycle efficiency, 35%–39%. Such turbines could also work in cogeneration and trigeneration arrangements, using various fuels such as liquids, gaseous fuels, wastes, coal, or biogas. Innovative technology in connection with ecology and the failure-free operation of the power plant strongly suggests the application of such devices at relatively small generating units (e.g., “prosumers” such as home farms and individual enterprises), assuring their independence from the main energy providers. Such solutions are in agreement with the politics of sustainable development.

scholarly journals Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3501 ◽  
Author(s):  
Mikielewicz ◽  
Kosowski ◽  
Tucki ◽  
Piwowarski ◽  
Stępień ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Power Plants ◽  
Pass System ◽  
Turbine Efficiency ◽  
Lower Heating Value ◽  
Wide Scale ◽  
Open Cycle ◽  
External Combustion ◽  
Gas Turbine Cycle

The use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating according to an open cycle with partial bypassing of external combustion chamber at the turbine exit (a new solution) and, for comparison, a turbine set operating according to an open cycle with a regenerator. The calculations were carried out for different fuels: gas from biomass gasification (LHV = 4.4 MJ/kg), biogas (LHV = 17.5 MJ/kg) and methane (LHV = 50 MJ/kg). It is demonstrated that analyzed solution enables construction of several kW power microturbines that might be used on a local scale. Such turbines, operated by prosumer’s type of organizations may change the efficiency of electricity generation on a country-wide scale evidently contributing to the sustainability of power generation, as well as the economy as a whole.

Development of Hybrid Power Systems Based on Direct Fuel Cell/Turbine Cycle

2005 ◽  
Author(s):  
Hossein Ghezel-Ayagh ◽  
Robert Sanderson ◽  
Jim Walzak
Keyword(s):  
Fuel Cell ◽  
Power Systems ◽  
Gas Turbine ◽  
Hybrid Systems ◽  
Gas Turbines ◽  
Power Plants ◽  
High Efficiency ◽  
Mechanical Design ◽  
Thermodynamic Cycle ◽  
Hybrid Power

FuelCell Energy Inc. (FCE) is developing ultra high efficiency Direct FuelCell/Turbine® (DFC/T®) hybrid power plants. Present activities are focused both on the demonstration of the DFC/T concept in small packaged hybrid power generation units for distributed generation, and the design of multi-megawatt (Multi-MW) hybrid systems for the wholesale electric power market. The development of Multi-MW DFC/T systems has been focused on the on the design of power plants with efficiencies approaching 75% (LHV of natural gas). The design efforts included thermodynamic cycle analysis of key gas turbine parameters such as compression ratio. The power plant designs were studied for near-term deployment utilizing the existing commercially available gas turbines and long-term deployment requiring advanced gas turbine technologies. A new fuel cell cluster concept was developed for mechanical design of Multi-MW systems. The concept utilizes the existing one-MW fuel cell modules as the building block for the Multi-MW hybrid systems.

FEATURES OF THE METHODOLOGY OF THERMODYNAMIC MODELING OF GAS TURBINE AND COMBINED ON THEIR BASIS POWER PLANTS

2017 ◽  
Author(s):  
Gennadii Liubchik ◽  
◽  
Nataliia Fialko ◽  
Aboubakr Regragui ◽  
Julii Sherenkovskii ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Thermodynamic Modeling ◽  
Power Plants ◽  
High Efficiency ◽  
Technical Facility

The article presents the enthalpy-entropy methodology of thermodynamic analysis of gas turbine and combined power plants on their basis, the results of testing the method on a real technical facility, proving its high efficiency.

scholarly journals Thermodynamic Analysis of Different Configurations of Combined Cycle Power Plants

2015 ◽  
Vol 5 (2) ◽  
pp. 89
Author(s):  
Munzer S. Y. Ebaid ◽  
Qusai Z. Al-hamdan
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Maximum Efficiency ◽  
Specific Work ◽  
Slight Effect ◽  
Turbine Engine ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

<p class="1Body">Several modifications have been made to the simple gas turbine cycle in order to increase its thermal efficiency but within the thermal and mechanical stress constrain, the efficiency still ranges between 38 and 42%. The concept of using combined cycle power or CPP plant would be more attractive in hot countries than the combined heat and power or CHP plant. The current work deals with the performance of different configurations of the gas turbine engine operating as a part of the combined cycle power plant. The results showed that the maximum CPP cycle efficiency would be at a point for which the gas turbine cycle would have neither its maximum efficiency nor its maximum specific work output. It has been shown that supplementary heating or gas turbine reheating would decrease the CPP cycle efficiency; hence, it could only be justified at low gas turbine inlet temperatures. Also it has been shown that although gas turbine intercooling would enhance the performance of the gas turbine cycle, it would have only a slight effect on the CPP cycle performance.</p>

Recuperators in Gas Turbine Systems

1998 ◽  
Author(s):  
Esa Utriainen ◽  
Bengt Sundén
Keyword(s):  
Research And Development ◽  
Gas Turbine ◽  
Cross Sections ◽  
Heat Exchangers ◽  
Power Plants ◽  
Pressure Ratio ◽  
Compact Heat Exchangers ◽  
Thermodynamic Cycles ◽  
Large Pressure ◽  
Gas Turbine Cycle

The application of recuperators in advanced thermodynamic cycles is growing due to stronger demands of low emissions of pollutants and the necessity of improving the cycle efficiency of power plants to reduce the fuel consumption. This paper covers applications and types of heat exchangers used in gas turbine units. The trends of research and development are brought up and the future need for research and development is discussed. Material aspects are covered to some extent. Attempts to achieve compact heat exchangers for these applications are also discussed. With the increasing pressure ratio in the gas turbine cycle, large pressure differences between the hot and cold sides exist. This has to be accounted for. The applicability of CFD (Computational Fluid Dynamics) is discussed and a CFD–approach is presented for a specific recuperator. This recuperator has narrow wavy ducts with complex cross-sections and the hydraulic diameter is so small that laminar flow prevails. The thermal-hydraulic performance is of major concern.

Modeling of Gas Turbine-Based Cogeneration System

2012 ◽  
Author(s):  
Farshid Zabihian ◽  
Alan S. Fung ◽  
Fabio Schuler
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Superheated Steam ◽  
Hot Water ◽  
Cogeneration System ◽  
Exhaust Stream ◽  
Low Efficiency ◽  
Gas Turbine Cycle ◽  
Wasted Energy

Gas turbine-based power plants generate a significant portion of world’s electricity. This paper presents the modeling of a gas turbine-based cogeneration cycle. One of the reasons for the relatively low efficiency of a single gas turbine cycle is the waste of high-grade energy at its exhaust stream. In order to recover this wasted energy, steam and/or hot water can be cogenerated to improve the cycle efficiency. In this work, a cogeneration power plant is introduced to use this wasted energy to produce superheated steam for industrial processes. The cogeneration system model was developed based on the data from the Whitby cogeneration power plant in ASPEN PLUS®. The model was validated against the operational data of the existing power plant. The electrical and total (both electrical and thermal) efficiencies were around 40% and 70% (LHV), respectively. It is shown that cogenerating electricity and steam not only significantly improve the general efficiency of the cycle but it can also recover the output and efficiency losses of the gas turbine as a result of high ambient temperature by generating more superheated steam. Furthermore, this work shows that the model could capture the operation of the systems with an acceptable accuracy.

Thermodynamic Study of Humid Air Gas Turbine Cycle Power Plants

2005 ◽  
Author(s):  
R. Yadav ◽  
P. Sreedhar Yadav
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Substantial Reduction ◽  
Thermodynamic Study ◽  
Humid Air ◽  
Turbine Plant ◽  
Design Engineers ◽  
Gas Turbine Plant ◽  
Gas Turbine Cycle

The major challenges before the design engineers of a gas turbine plant and its variants are the enhancement of power output, substantial reduction in NOx emission and improvement in plant thermal efficiency. There are various possibilities to achieve these objectives and humid air gas turbine cycle power plant is one of them. The present study deals with the thermodynamic study of humid air gas turbine cycle power plants based on first law. Using the modeling and governing equations, the parametric study has been carried out. The results obtained will be helpful in designing the humid air gas turbines, which are used as peaking units. The comparison of performance of humid air gas turbine cycle shows that it is superior to basic gas turbine cycle but inferior and more complex to steam injected cycle.

Enhancing Gas Turbine Operation With Heavy Fuel Oil

2013 ◽  
Author(s):  
Vikram Muralidharan ◽  
Matthieu Vierling
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Power Plants ◽  
High Efficiency ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Residual Oil ◽  
Heavy Fuel Oil ◽  
Hydro Power

Power generation in south Asia has witnessed a steep fall due to the shortage of natural gas supplies for power plants and poor water storage in reservoirs for low hydro power generation. Due to the current economic scenario, there is worldwide pressure to secure and make more gas and oil available to support global power needs. With constrained fuel sources and increasing environmental focus, the quest for higher efficiency would be imminent. Natural gas combined cycle plants operate at a very high efficiency, increasing the demand for gas. At the same time, countries may continue to look for alternate fuels such as coal and liquid fuels, including crude and residual oil, to increase energy stability and security. In over the past few decades, the technology for refining crude oil has gone through a significant transformation. With the advanced refining process, there are additional lighter distillates produced from crude that could significantly change the quality of residual oil used for producing heavy fuel. Using poor quality residual fuel in a gas turbine to generate power could have many challenges with regards to availability and efficiency of a gas turbine. The fuel needs to be treated prior to combustion and needs a frequent turbine cleaning to recover the lost performance due to fouling. This paper will discuss GE’s recently developed gas turbine features, including automatic water wash, smart cooldown and model based control (MBC) firing temperature control. These features could significantly increase availability and improve the average performance of heavy fuel oil (HFO). The duration of the gas turbine offline water wash sequence and the rate of output degradation due to fouling can be considerably reduced.

scholarly journals Gas Turbine Cycle Design Methodology: A Comparison of Parameter Variation With Numerical Optimization

1998 ◽  
Author(s):  
Joachim Kurzke
Keyword(s):  
Gas Turbine ◽  
Numerical Optimization ◽  
Graphical Representation ◽  
Thermodynamic Cycle ◽  
Parameter Variation ◽  
Parameter Study ◽  
Design Point ◽  
Optimization Task ◽  
Gas Turbine Cycle ◽  
Simulation Task

In gas turbine performance simulations often the question arises: What is the best thermodynamic cycle design point? This is an optimization task which can be attacked in two ways: One can do a series of parameter variations and pick from the resulting graphs the best solution or one can employ numerical optimization algorithms that produce a single cycle which fulfills all constraints. The conventional parameter study builds strongly on the engineering judgement and gives useful information over a range of parameter selections. However, when values for more than a few variables have to be determined while several constraints are existing, then numerical optimization routines can help to find the mathematical optimum faster and more accurately. Sometimes even an outstanding solution is found which was overlooked while doing a preliminary parameter study. For any simulation task a sophisticated graphical user interface is of great benefit. This is especially true for automated numerical optimizations. It is quite helpful to see on the screen of a PC how the variables are changing and which constraints are limiting the design. A quick and clear graphical representation of trade studies is also of great advantage. The paper describes how numerical optimization and parameter studies are implemented in a Windows-based PC program. As an example, the cycle selection of a derivative turbofan engine with a given core shows the merits of numerical optimization. The parameter variation is best suited for presenting the sensitivity of the result in the neighborhood of the optimum cycle design point.

Sign in / Sign up

Export Citation Format

Share Document