scholarly journals EVALUATION OF COATINGS TENDENCY TO THE PORES AND NON-METAL INCLUSIONS FORMATION IN A WELD

2020 ◽  
Vol 5 (9) ◽  
pp. 67-80
Author(s):  
L. Zhabrev ◽  
S. Chuppina ◽  
A. Shamshurin ◽  
E. Lebedeva ◽  
O. Panchenko
Keyword(s):  
Arc Welding ◽  
Polyvinyl Butyral ◽  
Chemical Transformations ◽  
X Ray ◽  
Welding Steel ◽  
Restoration Work ◽  
Electric Arc Welding ◽  
Physical And Chemical ◽  
Metal Spraying ◽  
Common Defect

The task of welding steel elements painted with various coatings is found in a number of industries at the stages of factory assembly and installation of large-sized structures, as well as during repair and restoration work. The porosity of the welded metal is the most common defect in electric arc welding without removing the coating, and the tendency to pore formation is a normalized parameter in the certification of interoperable primers (EN ISO 17652-2: 2003). The studies carried out cover wide-spread polyacrylate, alkyd, epoxy, polyvinyl butyral primers in an extended working thicknesses range. In addition, the evaluation technique is used for zinc-filled and organosilicate protective coat-ings. Based on the study of the nonmetallic inclusions composition in a weld by energy dispersive X-ray spectroscopy and using a scanning electron microscope, the behavior features of the coatings de-struction products and their derivatives during physical and chemical transformations under welding are described. The technological features of welding without coating removing are noted: stability of the mode parameters, resistance to metal spraying and coating burnout activity in the areas adjacent to a weld.

Electrical Porcelain Containing Ornamental Rock Waste: Microstructural Development

2010 ◽  
Vol 660-661 ◽  
pp. 692-696 ◽  
Author(s):  
M.A. Silva ◽  
J.N.F. Holanda
Keyword(s):  
Electron Microscopy ◽  
The Other ◽  
Electrical Porcelain ◽  
Microstructural Development ◽  
Chemical Transformations ◽  
X Ray Diffraction ◽  
X Ray ◽  
Aluminous Porcelain ◽  
Physical And Chemical ◽  
Scanning Electron

Aluminous electrical porcelains are used in the production of materials of high voltage insulators. The microstructure plays an important role in the performance of electrical porcelain. On the other hand, the porcelain materials undergo a series of physical and chemical transformations during firing. This makes the understanding of their microstructures rather complex. In this work was studied the microstructural development of electrical porcelain containing up to 35 wt.% of ornamental rock waste. The pieces ceramics were pressed at 50 MPa and sintered at 1300 °C. The porcelain pieces were characterized via X-ray diffraction and scanning electron microscopy. The results indicate that the presence of the ornamental rock waste influenced the microstructural development of the pieces of electrical aluminous porcelain.

A Comparative Study of Induced-Arc and Resistive Welds Employing SEM and X-Ray Emission Studies

1972 ◽  
Vol 30 ◽  
pp. 490-491
Author(s):  
Arthur J. Saffir ◽  
Donald I. Zenobia
Keyword(s):  
Arc Welding ◽  
Biomedical Applications ◽  
Copper Substrate ◽  
Precious Metals ◽  
Electrical Contacts ◽  
X Ray ◽  
Relative Potential ◽  
Physical And Chemical ◽  
Emission Studies ◽  
A Current

The purpose of this study was to evaluate the two techniques that are commercially used to bond the components of composite electrical contacts. These materials, usually consisting of a precious metal contacting region bonded to a copper substrate, offer substantial economy compared to similar devices made entirely from precious metals. They also possess unique desirable properties useful in other electronic and biomedical applications. However, these advantages can only be realized if the weld can withstand the severe physical and chemical environment in which it must operate.The resistive welds are created by bringing the components into contact and then providing a current in order to create sufficient heat for welding. Induced-arc welding requires more operations: the components are held apart with a relative potential of 10 to 100 volts; then they come into contact very briefly, 50 to 500 μsec; they are immediately drawn apart, striking an arc; finally, after arcing from 300 to 3000 μsec, they are forced together percussively while the current continues to flow.

Characterization of defects in tabular silver halide grains

1990 ◽  
Vol 48 (4) ◽  
pp. 1046-1047
Author(s):  
C. Goessens ◽  
D. Schryvers ◽  
J. Van Landuyt ◽  
A. Verbeeck ◽  
R. De Keyzer
Keyword(s):  
Radiation Damage ◽  
Silver Halide ◽  
Chemical Characteristics ◽  
X Ray ◽  
Free Region ◽  
Central Defect ◽  
Crystallographic Defects ◽  
Physical And Chemical ◽  
Two Sides

Silver halide grains (AgX, X=Cl,Br,I) are commonly recognized as important entities in photographic applications. Depending on the preparation specifications one can grow cubic, octahedral, tabular a.o. morphologies, each with its own physical and chemical characteristics. In the present study crystallographic defects introduced by the mixing of 5-20% iodide in a growing AgBr tabular grain are investigated. X-ray diffractometry reveals the existence of a homogeneous Ag(Br1-xIx) region, expected to be formed around the AgBr kernel. In fig. 1 a two-beam BF image, taken at T≈100 K to diminish radiation damage, of a triangular tabular grain is presented, clearly showing defect contrast fringes along four of the six directions; the remaining two sides show similar contrast under relevant diffraction conditions. The width of the central defect free region corresponds with the pure AgBr kernel grown before the mixing with I. The thickness of a given grain lies between 0.15 and 0.3 μm: as indicated in fig. 2 triangular (resp. hexagonal) grains exhibit an uneven (resp. even) number of twin interfaces (i.e., between + and - twin variants) parallel with the (111) surfaces. The thickness of the grains and the existence of the twin variants was confirmed from CTEM images of perpendicular cuts.

Electric arc welding and surfacing in repair of rails of Kyiv underground

2018 ◽  
Vol 2018 (2) ◽  
pp. 30-33
Author(s):  
G.V. Kuzmenko ◽  
◽  
V.M. Taganovsky ◽  
V.L. Sidorenko ◽  
◽  
...  
Keyword(s):  
Arc Welding ◽  
Electric Arc ◽  
Electric Arc Welding

scholarly journals Physical and chemical imaging of adhesive interfaces with soft X-rays

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Hiroyuki Yamane ◽  
Masaki Oura ◽  
Osamu Takahashi ◽  
Tomoko Ishihara ◽  
Noriko Yamazaki ◽  
...  
Keyword(s):  
Molecular Level ◽  
Covalent Bond ◽  
Chemical Imaging ◽  
Diglycidyl Ether ◽  
X Rays ◽  
X Ray ◽  
Covalent Bond Formation ◽  
Chemical States ◽  
The Individual ◽  
Physical And Chemical

AbstractAdhesion is an interfacial phenomenon that is critical for assembling carbon structural composites for next-generation aircraft and automobiles. However, there is limited understanding of adhesion on the molecular level because of the difficulty in revealing the individual bonding factors. Here, using soft X-ray spectromicroscopy we show the physical and chemical states of an adhesive interface composed of a thermosetting polymer of 4,4’-diaminodiphenylsulfone-cured bisphenol A diglycidyl ether adhered to a thermoplastic polymer of plasma-treated polyetheretherketone. We observe multiscale phenomena in the adhesion mechanisms, including sub-mm complex interface structure, sub-μm distribution of the functional groups, and molecular-level covalent-bond formation. These results provide a benchmark for further research to examine how physical and chemical states correlate with adhesion, and demonstrate that soft X-ray imaging is a promising approach for visualizing the physical and chemical states at adhesive interfaces from the sub-mm level to the molecular level.

Russellite: a second occurrence

1970 ◽  
Vol 37 (290) ◽  
pp. 705-707 ◽  
Author(s):  
L. C. Hodge
Keyword(s):  
Powder Diffraction ◽  
Western Australia ◽  
Original Description ◽  
Chemical Data ◽  
Green Material ◽  
X Ray ◽  
Fine Grained ◽  
Physical And Chemical ◽  
Pale Green

SummaryRussellite Bi2O3. WO3 occurs in a small pegmatite near Poona, Western Australia. The fine-grained yellow to pale green material is an inseparable mixture of russellite, bismite, koechlinite, and bismutite. X-ray powder diffraction, physical, and chemical data agree in general with the original description of the mineral from Cornwall, England. The original analyses made on micro quantities are now supplemented by analyses on macro quantities.

Monitoring of Fluctuations in the Physical and Chemical Properties of a High-Calcium Fly Ash

1987 ◽  
Vol 113 ◽  
Author(s):  
Scott Schlorholtz ◽  
Ken Bergeson ◽  
Turgut Demirel
Keyword(s):  
Fly Ash ◽  
Chemical Properties ◽  
Operating Conditions ◽  
Physical And Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
High Calcium ◽  
Physical And Chemical ◽  
And Chemical Properties

ABSTRACTThe physical and chemical properties of fly ash produced at Ottumwa Generating Station have been monitored since April, 1985. The fly ash is produced from burning a low sulfur, sub-bituminous coal obtained from the Powder River Basin near Gillette, Wyoming. One-hundred and sixty samples of fly ash were obtained during the two year period. All of the samples were subjected to physical testing as specified by ASTM C 311. About one-hundred of the samples were also subjected to a series of tests designed to monitor the self-cementing properties of the fly ash. Many of the fly ash samples were subjected to x-ray diffraction and fluorescence analysis to define the mineralogical and chemical composition of the bulk fly ash as a function of sampling date. Hydration products in selected hardened fly ash pastes, were studied by x-ray diffraction and scanning electron microscopy. The studies indicated that power plant operating conditions influenced the compressive strength of the fly ash paste specimens. Mineralogical and morphological studies of the fly ash pastes indicated that stratlingite formation occurred in the highstrength specimens, while ettringite was the major hydration product evident in the low-strength specimens.

scholarly journals Characterization of Spent Ni-MH Batteries

2012 ◽  
Vol 730-732 ◽  
pp. 569-574
Author(s):  
Marta Cabral ◽  
Fernanda Margarido ◽  
Carlos A. Nogueira
Keyword(s):  
Quantitative Analysis ◽  
Electrode Materials ◽  
Phase Identification ◽  
Recycling Process ◽  
X Ray ◽  
Leaching Experiments ◽  
Plastic Components ◽  
Definition Of ◽  
Physical And Chemical

Spent Ni-MH batteries are not considered too dangerous for the environment, but they have a considerable economical value due to the chemical composition of electrodes which are highly concentrated in metals. The present work aimed at the physical and chemical characterisation of spent cylindrical and thin prismatic Ni-MH batteries, contributing for a better definition of the recycling process of these spent products. The electrode materials correspond to more than 50% of the batteries weight and contain essentially nickel and rare earths (RE), and other secondary elements (Co, Mn, Al). The remaining components are the steel parts from the external case and supporting grids (near 30%) containing Fe and Ni, and the plastic components (<10%). Elemental quantitative analysis showed that the electrodes are highly concentrated in metals. Phase identification by X-ray powder diffraction combined with chemical analysis and leaching experiments allowed advancing the electrode materials composition. The cathode is essentially constituted by 6% metallic Ni, 66% Ni(OH)2, 4.3% Co(OH)2 and the anode consists mainly in 62% RENi5 and 17% of substitutes and/or additives such as Co, Mn and Al.

Sign in / Sign up

Export Citation Format

Share Document