Effect of bending direction on the mechanical behaviour of interlocking nail systems

2009 ◽  
Vol 22 (04) ◽  
pp. 264-269 ◽  
Author(s):  
R. P. Guillou ◽  
D. Ting ◽  
M. T. Sinnott ◽  
E. Meyer ◽  
R. C. Haut ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Clinical Significance ◽  
Bone Healing ◽  
Mechanical Behaviour ◽  
Tibial Fracture ◽  
The Novel ◽  
Synthetic Bone ◽  
Maximum Deformation ◽  
Interlocking Nail ◽  
Angle Stable

Summary Objectives: To compare the mechanical properties of various interlocking nail constructs in medio-lateral (ML) and cranio-caudal (CC) bending. Methods: Synthetic bone models simulating a severely comminuted tibial fracture were treated with either screwed or bolted, 6 or 8 mm standard interlocking nails (ILN), or an angle-stable ILN (AS-ILN), after which they were then sequentially tested in ML and CC bending. Construct compliance, maximum angular deformation (MaxDef) and slack were statistically compared (p<0.05). Results: The compliance of all constructs was significantly greater in CC than in ML bending. However, due to the presence of a greater slack in the ML plane, standard ILN constructs sustained significantly more deformation in that plane. Maximum deformation of the novel AS-ILN constructs was the smallest of all constructs and consistently occurred without slack regardless of bending direction. Clinical significance: This study suggested that standard ILN construct overall deformation and acute instability (slack) may be more critical in ML than in CC bending. Conversely, the small MaxDef and the absence of slack in both bending planes seen in novel angle-stable AS-ILN may provide optimal construct stability and in turn may be more conducive to bone healing.

In VivoBiomechanical Evaluation of a Novel Angle-Stable Interlocking Nail Design in a Canine Tibial Fracture Model

2014 ◽  
Vol 43 (3) ◽  
pp. 271-281 ◽  
Author(s):  
Loïc M. Déjardin ◽  
Julien B. Cabassu ◽  
Reunan P. Guillou ◽  
Mark Villwock ◽  
Laurent P. Guiot ◽  
...  
Keyword(s):  
Tibial Fracture ◽  
Fracture Model ◽  
Interlocking Nail ◽  
Angle Stable

scholarly journals Preliminary mechanical evaluation of two novel veterinary angle-stable-threaded interlocking nail systems

2022 ◽  
Vol 52 (6) ◽  
Author(s):  
Jordana da Costa Nóbrega ◽  
Dayvid Vianêis Farias de Lucena ◽  
Bruno Watanabe Minto ◽  
Luis Gustavo Gosuen Gonçalves Dias
Keyword(s):  
Plastic Deformation ◽  
The Other ◽  
Long Bones ◽  
The Novel ◽  
Single Plane ◽  
Compression Load ◽  
Interlocking Nail ◽  
Angle Stable ◽  
Initial Hypothesis ◽  
Biomechanical Tests

ABSTRACT: The interlocking nail represents an excellent option as a surgical approach to treat fractures in long bones in veterinary medicine. However, failures were reported mainly due to a slack present in the interface of the rod with the screws. The present study tested and mechanically compare axial compression loads of two novel models of stable angle interlocking nails with threaded holes. Among the two models, one was uniplanar and the other was multiplanar with orthogonally arranged distal holes. Twenty-one specimens made of polylactic acid were used for the implantation of interlocking nail´s rods, divided into three groups: conventional interlocking nail (G1), novel interlocking nail with a stable angle with holes arranged in a single plane (G2), and novel interlocking nail with a stable angle in two planes, with the penultimate hole at 90 degrees from the others (G3). Biomechanical tests were performed using axial, cyclic, and destructive compression load for comparison between them. All the specimens showed plastic deformation in the screws after destructive tests, in both proximal and distal sides, being highly intense in G1. G2 and G3 of the stable angle rods supported higher loads than G1 in all tests performed (P<0.05). The novel stems did not differ statistically from each other (P>0.05). The initial hypothesis that the novel models would provide increased stability was confirmed; however, no differences were demonstrated between them. The screw locking system on the rods allowed high resistance values in the tests performed, proving to be effective and potentially applicable in real clinical situations.

scholarly journals Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

2021 ◽  
Vol 22 (7) ◽  
pp. 3391
Author(s):  
Sylwia Grabska-Zielińska ◽  
Alina Sionkowska ◽  
Ewa Olewnik-Kruszkowska ◽  
Katarzyna Reczyńska ◽  
Elżbieta Pamuła
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Physicochemical Properties ◽  
Silk Fibroin ◽  
Three Dimensional ◽  
Microscopy Imaging ◽  
Maximum Deformation ◽  
One Step ◽  
Chitosan Blends ◽  
Fourier Transfer Infrared Spectroscopy

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

scholarly journals Evolution of the viscoelastic properties of painting stratigraphies: a moisture weathering and nanoindentation approach

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Mathilde Tiennot ◽  
Davide Iannuzzi ◽  
Erma Hermens
Keyword(s):  
Mechanical Properties ◽  
Relative Humidity ◽  
Cultural Heritage ◽  
Mechanical Behaviour ◽  
Viscoelastic Properties ◽  
Viscoelastic Behaviour ◽  
Storage And Loss Moduli ◽  
Heritage Studies ◽  
Paint Films ◽  
The Impact

AbstractIn this investigation on the mechanical behaviour of paint films, we use a new ferrule-top nanoindentation protocol developed for cultural heritage studies to examine the impact of repeated relative humidity variations on the viscoelastic behaviour of paint films and their mechanical properties in different paint stratigraphies through the changes in their storage and loss moduli. We show that the moisture weathering impact on the micromechanics varies for each of these pigment-oil systems. Data from the nanoindentation protocol provide new insights into the evolution of the viscoelastic properties dsue to the impact of moisture weathering on paint films.

scholarly journals Zn-Containing Membranes for Guided Bone Regeneration in Dentistry

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1797
Author(s):  
Manuel Toledano ◽  
Marta Vallecillo-Rivas ◽  
María T. Osorio ◽  
Esther Muñoz-Soto ◽  
Manuel Toledano-Osorio ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bone Regeneration ◽  
Bone Healing ◽  
Bone Repair ◽  
Complex Modulus ◽  
Bacterial Colonization ◽  
Guided Bone Regeneration ◽  
M2 Macrophage

Barrier membranes are employed in guided bone regeneration (GBR) to facilitate bone in-growth. A bioactive and biomimetic Zn-doped membrane with the ability to participate in bone healing and regeneration is necessary. The aim of the present study is to state the effect of doping the membranes for GBR with zinc compounds in the improvement of bone regeneration. A literature search was conducted using electronic databases, such as PubMed, MEDLINE, DIMDI, Embase, Scopus and Web of Science. A narrative exploratory review was undertaken, focusing on the antibacterial effects, physicochemical and biological properties of Zn-loaded membranes. Bioactivity, bone formation and cytotoxicity were analyzed. Microstructure and mechanical properties of these membranes were also determined. Zn-doped membranes have inhibited in vivo and in vitro bacterial colonization. Zn-alloy and Zn-doped membranes attained good biocompatibility and were found to be non-toxic to cells. The Zn-doped matrices showed feasible mechanical properties, such as flexibility, strength, complex modulus and tan delta. Zn incorporation in polymeric membranes provided the highest regenerative efficiency for bone healing in experimental animals, potentiating osteogenesis, angiogenesis, biological activity and a balanced remodeling. Zn-loaded membranes doped with SiO2 nanoparticles have performed as bioactive modulators provoking an M2 macrophage increase and are a potential biomaterial for promoting bone repair. Zn-doped membranes have promoted pro-healing phenotypes.

scholarly journals Effect of the mechanical properties and mode loading on the mechanical behaviour of weldment: a numerical analysis

2013 ◽  
Vol 16 (4) ◽  
pp. 853-859 ◽  
Author(s):  
Meddah Hadj Miloud ◽  
Ould chikh Bahri ◽  
Benhamena Ali ◽  
Benguediab Mohamed ◽  
Bouchouicha Benattou
Keyword(s):  
Mechanical Properties ◽  
Numerical Analysis ◽  
Mechanical Behaviour

scholarly journals Atomistic investigation into the mechanical behaviour of crystalline and amorphous TiO2 nanotubes

RSC Advances ◽  
2016 ◽  
Vol 6 (33) ◽  
pp. 28121-28129 ◽  
Author(s):  
Yanan Xu ◽  
Mingchao Wang ◽  
Ning Hu ◽  
John Bell ◽  
Cheng Yan
Keyword(s):  
Mechanical Properties ◽  
Molecular Dynamics ◽  
Titanium Dioxide ◽  
Molecular Dynamics Simulations ◽  
Mechanical Behaviour ◽  
Tio2 Nanotubes ◽  
Amorphous Tio2 ◽  
Dynamics Simulations

The mechanical properties of titanium dioxide (TiO2) nanotubes are studied based on molecular dynamics simulations.

scholarly journals The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3798
Author(s):  
Meng Sun ◽  
Dong Li ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Time ◽  
Volume Fraction ◽  
Low Cost ◽  
Solution Treatment ◽  
Solution Temperature ◽  
The Novel ◽  
Α Phase ◽  
The Cost

In order to reduce the cost of titanium alloys, a novel low-cost Ti-3Al-5Mo-4Cr-2Zr-1Fe (Ti-35421) titanium alloy was developed. The influence of heat treatment on the microstructure characteristics and mechanical properties of the new alloy was investigated. The results showed that the microstructure of Ti-35421 alloy consists of a lamina primary α phase and a β phase after the solution treatment at the α + β region. After aging treatment, the secondary α phase precipitates in the β matrix. The precipitation of the secondary α phase is closely related to heat treatment parameters—the volume fraction and size of the secondary α phase increase when increasing the solution temperature or aging time. At the same solution temperature and aging time, the secondary α phase became coarser, and the fraction decreased with increasing aging temperature. When Ti-35421 alloy was solution-treated at the α + β region for 1 h with aging surpassing 8 h, the tensile strength, yield strength, elongation and reduction of the area were achieved in a range of 1172.7–1459.0 MPa, 1135.1–1355.5 MPa, 5.2–11.8%, and 7.5–32.5%, respectively. The novel low-cost Ti-35421 alloy maintains mechanical properties and reduces the cost of materials compared with Ti-3Al-5Mo-5V-4Cr-2Zr (Ti-B19) alloy.

The Silorane-based Resin Composites: A Review

2017 ◽  
Vol 42 (1) ◽  
pp. E24-E34 ◽  
Author(s):  
GA Maghaireh ◽  
NA Taha ◽  
H Alzraikat
Keyword(s):  
Mechanical Properties ◽  
Bond Strength ◽  
Clinical Significance ◽  
Physical And Mechanical Properties ◽  
Marginal Adaptation ◽  
Resin Composites ◽  
Restorative Material ◽  
Polymerization Shrinkage ◽  
Tooth Structure

SUMMARY This article aims to review the research done on the silorane-based resin composites (SBRC) regarding polymerization shrinkage and contraction stresses and their ability to improve the shortcomings of the methacrylate-based resin composites (MRBC). Special attention is given to their physical and mechanical properties, bond strength, marginal adaptation, and cusp deflection. The clinical significance of this material is critically appraised with a focus on the ability of SBRC to strengthen the tooth structure as a direct restorative material. A search of English peer-reviewed dental literature (2003-2015) from PubMed and MEDLINE databases was conducted with the terms “low shrinkage” and “silorane composites.” The list was screened, and 70 articles that were relevant to the objectives of this work were included.

Mechanical Failure of Angle Locking Plates in Distal Comminuted Tibial Fractures

2016 ◽  
Vol 695 ◽  
pp. 118-122 ◽  
Author(s):  
Razvan Ene ◽  
Zsombor Panti ◽  
Mihai Nica ◽  
Marian Pleniceanu ◽  
Patricia Ene ◽  
...  
Keyword(s):  
Internal Fixation ◽  
Bone Healing ◽  
Tibial Fracture ◽  
Weight Bearing ◽  
Healing Process ◽  
Biomechanical Properties ◽  
Implant Failure ◽  
Locking Plates ◽  
Non Union ◽  
Tibial Pilon

Distal comminuted tibial fracture with or without intra-articular involvement is a very common injury of the lower limb, especially in younger patients due to high energy trauma. The anatomical and biomechanical properties of this segment of tibia, makes this pathology a major surgical challenge with a preserved clinical outcome. The aim of this study is to present different outcome of tibial fracture, treated with open reduction and internal fixation (ORIF) with titanium angle locking plates (ALP) and to underline the physiological and non-physiological bone healing effects on implants. In this study we included 48 patients with tibial pilon fracture who underwent to ORIF, applying ALP in the Orthopedics and Trauma department of the University Emergency Hospital in Bucharest. Due to preserved biomechanical properties of ALP and this anatomical region, weight bearing is not allowed till 6 to 8 weeks. Comminuted fracture of this part of tibia often have de-vascularized bony fragments which leads to delayed union or non-union. These complications often lead to implant failure, improper bone healing or non-union. Internal fixation with angle stable screws, offers a good stability of reduction in the early postoperative period. Titanium angle locking plates offers good anatomical reduction and stable fixation in the early period of healing process. Due to its rigid, fixed position of the screws in the plates, bone remodelling during healing process and early weight bearing, increases the mechanical failure of implant.Keywords: tibial pilon fractures, angle locking plates, implant failure.

Sign in / Sign up

Export Citation Format

Share Document