Reducing the Environmental Pollution from Diesel Engine Fuelled with Eco- Friendly Biodiesel Blends

2019 ◽  
Vol 1 (2) ◽  
pp. 35-44
Author(s):  
Ramesh C ◽  
Murugesan A ◽  
Vijayakumar C
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Direct Injection ◽  
Energy System ◽  
Compression Ignition Engine ◽  
Biodiesel Blends ◽  
Harmful Emissions ◽  
Ignition Quality

Diesel engines are widely used for their low fuel consumption and better efficiency. Fuel conservation, efficiency and emission control are always the investigation points in the view of researchers in developing energy system. India to search for a suitable environmental friendly alternative to diesel fuel. The regulated emissions from diesel engines are carbon monoxide (CO), Hydrocarbons (HC), NOx and Particulate matter. It creates cancer, lungs problems, headaches and physical and mental problems of human. This paper focuses on the substitution of fossil fuel diesel with renewable alternatives fuel such as Biodiesel. Biodiesel is much clear than fossil diesel fuel and it can be used in any diesel engine without major modification. The experiment was conducted in a single-cylinder four-stroke water-cooled 3.4 kW direct injection compression ignition engine fueled with non-edible Pungamia oil biodiesel blends. The experimental results proved that up to 40% of Pungamia oil biodiesel blends give better results compared to diesel fuel. The AVL 444 di-gas analyzer and AVL 437 smoke meter are used to measure the exhaust emissions from the engine. The observation of results, non-edible Pongamia biodiesel blended fuels brake thermal efficiency (3.59%) is improved and harmful emissions like CO, unburned HC, CO2, Particulate matter, soot particles, NOx and smoke levels are 29.67%, 26.65%, 33.47%, 39.57%, +/- 3.5 and 41.03% is decreased respectively compared to the diesel fuel. This is due to biodiesel contains the inbuilt oxygen content, ignition quality, carbon burns fully, less sulphur content, no aromatics, complete CO2 cycle.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals Study on Particulate Matter of Diesel Engine Using Waste Cooking Oil

2015 ◽  
Vol 773-774 ◽  
pp. 420-424 ◽  
Author(s):  
Nur Fauziah Jaharudin ◽  
Nur Atiqah Ramlan ◽  
Mohd Herzwan Hamzah ◽  
Abdul Adam Abdullah ◽  
Rizalman Mamat
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Engine Speed ◽  
Direct Injection ◽  
Waste Cooking Oil ◽  
Manufacturing Cost ◽  
Alternative Source ◽  
Cooking Oil

Particulate matter (PM) is one of the major pollutants emitted by diesel engine which have adverse effects on human health. Accordingly, many researches have been done to find alternative fuels that are clean and efficient. Biodiesel is preferred as an alternative source for diesel engine which produces lower PM than diesel fuel. However, the manufacturing cost of biodiesel from vegetable oil is expensive. Therefore, using waste cooking oil (WCO) for biodiesel would be more economical and sustainable solution. The characteristics of direct injection diesel engine in term of the PM have been investigated experimentally in this study. The experiments were conducted using single cylinder diesel engine with different speed (1200 rpm, 1500 rpm, 1800 rpm, 2100 rpm, 2400 rpm) at constant load. PM emission of WCO B100 and diesel fuel was compared and the effect of PM components such as soluble organic fraction (SOF) and soot were studied. The result showed WCO B100 reduces the PM emission at all engine speed. Furthermore, both fuels showed highest reduction of PM concentration at moderate engine speed of 1500 rpm.

scholarly journals An experimental study of the combusition and emission performances of 2,5-dimethylfuran diesel blends on a diesel engine

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 543-553 ◽  
Author(s):  
Helin Xiao ◽  
Pengfei Zeng ◽  
Liangrui Zhao ◽  
Zhongzhao Li ◽  
Xiaowei Fu
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Operating Conditions ◽  
Effective Pressure ◽  
Compression Ignition Engine ◽  
Brake Mean Effective Pressure ◽  
Combustion Duration ◽  
Significant Difference ◽  
Hc Emissions

Experiments were carried out in a direct injection compression ignition engine fueled with diesel-dimethylfuran blends. The combustion and emission performances of diesel-dimethylfuran blends were investigated under various loads ranging from 0.13 to 1.13 MPa brake mean effective pressure, and a constant speed of 1800 rpm. Results indicate that diesel-dimethylfuran blends have different combustion performance and produce longer ignition delay and shorter combustion duration compared with pure diesel. Moreover, a slight increase of brake specific fuel consumption and brake thermal efficiency occurs when a Diesel engine operates with blended fuels, rather than diesel fuel. Diesel-dimethylfuran blends could lead to higher NOx emissions at medium and high engine loads. However, there is a significant reduction in soot emission when engines are fueled with diesel-dimethylfuran blends. Soot emissions under each operating conditions are similar and close to zero except for D40 at 0.13 MPa brake mean effective pressure. The total number and mean geometric diameter of emitted particles from diesel-dimethylfuran blends are lower than pure diesel. The tested fuels exhibit no significant difference in either CO or HC emissions at medium and high engine loads. Nevertheless, diesel fuel produces the lowest CO emission and higher HC emission at low loads of 0.13 to 0.38 MPa brake mean effective pressure.

scholarly journals ENERGY ANALYSIS OF KARANJA OIL AS A SUPPLEMENTARY FUEL FOR COMPRESSION IGNITION ENGINE

2016 ◽  
Vol 9 (2) ◽  
pp. 97-101
Author(s):  
Biplab Das ◽  
Pradip Lingfa
Keyword(s):  
Experimental Investigation ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Energy Analysis ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Biodiesel Blends ◽  
Karanja Oil ◽  
Load Conditions

The paper highlights the results of an experimental investigation carried out on Karanja oil as a supplementary for diesel fuel in Compression Ignition engine. In the present study, triglycerides of Karanja oil is converted into mono-ester (biodiesel) using based catalyst transesterfication process. Karanja biodiesel is blended with petroleum diesel in the volumetric proportions of 2−10%. Results reveal that the performance characteristics of Karanja biodiesel blends are well comparable with diesel fuel. The emission characteristics such as CO, HC and smoke are found to be lower for Karanja biodiesel blends at all the engine load conditions compared to diesel fuel. Hence, it is concluded that Karanja oil at lower blends can be used in diesel engine without any substantial engine modification.

Humidification Effect on the Performance and Emissions of (DI) Diesel Engine Running on Diesel Fuel with Biodiesel Blended Nano Additives

2021 ◽  
Vol 39 (5A) ◽  
pp. 790-803
Author(s):  
Hussein Jumaa ◽  
Mahmoud A. Mashkour
Keyword(s):  
Diesel Engine ◽  
Taguchi Method ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Waste Cooking Oil ◽  
Compression Ignition Engine ◽  
Performance And Emissions ◽  
Di Diesel Engine ◽  
Nano Additives ◽  
20 Nm

The effect of humidification of the air on the performance of a compression ignition engine operating on diesel, biodiesel with nano additives was investigated. The experiment was carried out on a single-cylinder, four-stroke, naturally aspirated water-cooled, direct injection Ricardo (E6/US) diesel engine at a constant speed of 1800 rpm, and varying loads. A mixture of Biodiesel (waste cooking oil) and diesel fuel by four ratios (B5, B10, B15, and B20) was used in the experiment. Besides, five concentrations of Iron oxide nanoparticles (Fe2O3, with particle size 20 nm) as fuel-additives were prepared (10 ppm, 30 ppm, 50 ppm, 70 ppm, and 100 ppm), and added to the test fuels (Bio-Diesel).  Taguchi Method by DOE was used for the optimization in this investigation. The results of Taguchi Method experiments identified the biodiesel (B20), nano additive (100 ppm), relative humidity (65%). The experimental results manifested that BTE improved by 17.62% and BSFC decreased by 12.72%, while NOx and PM reduced by 8.45%, 24.17%, respectively.

scholarly journals Biodiesel from Crude Tall Oil and Its NOx and Aldehydes Emissions in a Diesel Engine Fueled by Biodiesel-Diesel Blends with Water Emulsions

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 126
Author(s):  
Murari Mohon Roy ◽  
Md Shariful Islam ◽  
Md Nur Alam
Keyword(s):  
Fatty Acids ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Woody Plant ◽  
Substantial Reduction ◽  
Plant Oil ◽  
Tall Oil ◽  
Water Emulsion ◽  
Biodiesel Blends

Using biodiesel in diesel engines is beneficial for reducing emissions of carbon monoxide (CO), hydrocarbons (HC) and particulate matters (PM). Biodiesel is usually produced from vegetable oils or animal fats. When produced from plant oil or woody plant sources, biodiesel can reduce a significant amount of carbon dioxide on a life cycle basis. The objective of this study is to produce biodiesel from a non-conventional woody plant source that is, crude tall oil, which is a dark brown viscous liquid extracted and processed in wood pulping plants. It contains a high percentage of fatty acids. From raw crude tall oil, tall oil fatty acids were separated and were successfully used for the production of biodiesel in this study. Although biodiesel produces lower CO, HC and PM than petroleum diesel fuel, it produces higher oxides of nitrogen (NOx) emissions in diesel engines. Water emulsifications of diesel-biodiesel blends are investigated in a direct injection (DI) diesel engine in this work to understand their potential for NOx reduction. When using 10% water in the emulsions, NOx was reduced by nearly 15%. In aldehyde emissions, B100 showed 35% lower aldehydes and B100 with 10% water emulsion produced nearly 90% lower aldehydes than diesel fuel - a substantial reduction. Therefore, this study accomplished the desired goal of producing biodiesel from a non-conventional source, which satisfies ASTM biodiesel standard and results in lower NOx and aldehydes emissions with water emulsifications of diesel-biodiesel blends in a diesel engine compared to that of diesel fuel.

scholarly journals The effect of Diesel-Methanol Blends with Volumetric Proportions on The Performance and Emissions of A Diesel Engine

Mechanika ◽  
2019 ◽  
Vol 25 (5) ◽  
pp. 363-369 ◽  
Author(s):  
ADNAN BERBER
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Gas Temperature ◽  
Engine Torque ◽  
Performance And Emissions ◽  
Maximum Decrease

In this work, the methanol is added to the diesel fuel in the volumetric proportions of 5%-%10-%15 to diminish negative environmental impacts of diesel engines. The diesel-methanol blends in the various proportions are tested in a single-cylinder direct-injection diesel engine. According to the test results, the addition of methanol to the diesel fuel causes a maximum decrease of 13.07 % in the engine torque, and a maximum decrease of 12.54 % in the specific fuel consumption. On the other hand, the exhaust emission results show that the values of CO and CO2 decrease 38.4 % and 5.04%. However, the increase of 3.66% in the exhaust gas temperature causes the increase of 17.1% in the NOx emission. Also, a significant decrease of 39.37% in the smoke opacity is observed compared to that of the diesel fuel. Although the addition of methanol to diesel fuel causes a slightly decrease in the engine performance, the diesel-methanol blends have a reasonable and considerable positive effect on environmental concerns of diesel engines.

Reduction of Nitric Oxides and Soot by Premixed Fuel in Partial HCCI Engine

2005 ◽  
Vol 128 (3) ◽  
pp. 497-505 ◽  
Author(s):  
Dae Sik Kim ◽  
Myung Yoon Kim ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Direct Injection ◽  
Heating System ◽  
Injection System ◽  
Intake Manifold ◽  
Soot Emission ◽  
Nitric Oxides ◽  
Compression Ignition Engine

In order to obtain the reduction effect of NOx and soot emission in a partial homogeneous charge compression ignition engine, premixed fuel was supplied with direct injection diesel fuel. Several additional systems such as a premixed fuel injection system, exhaust gas recirculation (EGR) system, supercharger, and air heating system were equipped in the intake manifold of conventional diesel engine. Premixed fuel with air was compressed and ignited by the directly injected diesel fuel in the combustion chamber at the end of compression stroke. The effect of premixed fuel on combustion and emission characteristics of HCCI diesel engine was investigated experimentally under various conditions of intake air temperature, pressure, and EGR rate. The results showed that in case of the use of gasoline as a premixed fuel, single stage ignition is found, but premixing the diesel fuel accompanies the cool flame prior to the combustion of the directly injected diesel fuel. For the gasoline premixed fuel, both NOx and soot can be reduced by the increase of premixed ratio simultaneously. However, for the diesel premixed fuel, the increase of premixed ratio does not have a significant effect in reducing the soot emission.

scholarly journals Effect of butanol on fuel consumption and smoke emission of direct injection diesel engine fueled by jatropha oil and diesel fuel blends with cold EGR system

2018 ◽  
Vol 49 ◽  
pp. 02010
Author(s):  
Syarifudin ◽  
Syaiful ◽  
Eflita Yohana
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Alternative Fuels ◽  
Fossil Fuels ◽  
Direct Injection ◽  
Jatropha Oil ◽  
Fuel Blend ◽  
Direct Injection Diesel Engine

Diesel engines are widely used in industry, automotive, power generation due to better reliability and higher efficiency. However, diesel engines produce high smoke emissions. The main problem of diesel engine is actually the use of fossil fuels as a source of energy whose availability is diminishing. Therefore alternative fuels for diesel fuels such as jatropha and butanol are needed to reduce dependence on fossil fuels. In this study, the effect of butanol usage on fuel consumption and smoke emissions of direct injection diesel engine fueled by jatropha oil and diesel fuel with cold EGR system was investigated. The percentage of butanol was in the range of 5 to 15%, jatropha oil was in the range of 10 to 30% and the balance was diesel fuel. Cold EGR was varied through valve openings from 0 to 100% with 25% intervals. The experimental data shows that the BSFC value increases with increasing percentage of butanol. In addition, the use of EGR results in a higher increase of BSFC than that without EGR. While the addition of butanol into a blend of jatropha oil and diesel fuel causes a decrease in smoke emissions. The results also informed that the use of EGR in the same fuel blend led to increased smoke emissions.

Sign in / Sign up

Export Citation Format

Share Document