scholarly journals Mechanical and tribological properties of nano-sized Al2O3 particles on ADC12 alloy composites with Strontium modifier produced by stir casting method

2021 ◽  
Vol 3 (1) ◽  
pp. 9-20
Author(s):  
Muhammad Wira Akira ◽  
Hanuna Haritsah ◽  
Anne Zulfia ◽  
Ekavianti Prajatelistia
Keyword(s):  
Tribological Properties ◽  
High Performance ◽  
Spinel Phase ◽  
Stir Casting ◽  
Grain Refiner ◽  
Interface Area ◽  
Alloy Matrix ◽  
Mechanical And Tribological Properties ◽  
Al2o3 Particles ◽  
Microstructure Modifier

Nano-Al2O3 particles were incorporated into ADC12 alloy with the addition of Al-5Ti-B, Al-Sr, and Mg to achieve high performance in mechanical and tribological properties. In this study, varied nano-Al2O3 was used from 0.25 vf-% to  0.5 vf-% through stir casting methods to discover the optimum amount to obtain high performance. Besides, the inclusion of grain refiner Al-5Ti-B and microstructure modifier Al-Sr is expected to improve performance to the next level. However, porosity and agglomeration still be a concern in Aluminum alloy matrix composite fabrication. The presence of spinel phase MgAl2O4 in the interface area between nano-Al2O3 particles and ADC12 alloy is relied upon to minimize this porosity and agglomeration issue. The optimum of tensile strength and hardness was found at 0.35 vf-% Al2O3 and wear rate at 0.4 vf%. Although, the optimum point of wear found at 0.4 vf%, porosity began to increase at 0.4 vf% as well. As a result, 0.35 vf% addition of the nano-Al2O3 gives the best performance for the composite.

The Role of Al2O3 Particles on Mechanical Properties and Microstructure of Aluminum A356 Composites Produced by Stir Casting Method

2020 ◽  
Vol 1000 ◽  
pp. 185-192
Author(s):  
Hanuna Haritsa ◽  
Muhammad Wira Akira ◽  
Anne Zulfia Syahrial
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Spinel Phase ◽  
Stir Casting ◽  
Reinforced Composites ◽  
Interface Area ◽  
Casting Method ◽  
Al2o3 Particles

This study was conducted to investigate the effect of Al2O3 on characteristics of A356 reinforced composites. The addition of Al2O3 as reinforced varied from 2 vf-% to 15 vf-% through Stir Casting methods to obtain the optimum addition Al2O3 as reinforced in mechanical properties of composite A356 as matrix and Al2O3 as reinforcement. Magnesium with of 10 wt-% was added to improve wettability between Al2O3 particles and Al A356. Addition of Magnesium is expected to form the spinel phase MgAl2O4 in interface area between Al2O3 and Al A356.The optimum tensile strength was found at 2 vf- Al2O3 with value 131.55 Mpa. However, the value is still lower than the tensile strength of Al A356 As cast. It is caused due to the porosity and the agglomeration of Al2O3 were found in the microstructure of the composite Al A356/Al2O3. The Hardness increased from material monolithic Al A356 as cast, reached 37.43 HRB.

Preparation of high-performance PEEK anti-wear blends with melt-processable PTFE

2019 ◽  
Vol 32 (6) ◽  
pp. 645-654
Author(s):  
Xiaotao Qiu ◽  
Congli Fu ◽  
Aiqun Gu ◽  
Yang Gao ◽  
Xiuli Wang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Wear Resistance ◽  
Surface Analysis ◽  
Tribological Properties ◽  
High Performance ◽  
Tribological Performance ◽  
Mechanical And Tribological Properties ◽  
The Past ◽  
Wide Range ◽  
Potential Applications

High-performance anti-wear polyetheretherketone/polytetrafluoroethylene (PEEK/PTFE) blends have drawn much attention over the past few years, owing to their wide range of potential applications. However, a convenient and effective method to prepare such blends with superior mechanical and tribological properties is still lacking. In this work, we propose a promising approach that uses melt-processable PTFE (MP PTFE), instead of conventional PTFE, to prepare anti-wear blends. MP PTFE, with melt flow abilities under appropriate conditions, can disperse homogeneously in PEEK, enhancing both the mechanical and tribological properties of the PEEK/PTFE blend. To prove this postulation, in this work, both MP PTFE and commercial PTFE were blended with PEEK, separately, and the effects of PTFE type and content on the tensile and tribological properties of the blends were studied. The results showed that, although the addition of commercial PTFE to PEEK could increase the wear resistance, it decreased the tensile strength of PEEK significantly. Compared to the blends with commercial PTFE, the blends with MP PTFE exhibited better tribological performance and higher tensile strength for PTFE content below 10 wt%. It was confirmed that the better dispersion of MP PTFE in PEEK endowed the blends with higher tensile strength. The surface analysis indicated that the MP PTFE could readily migrate to and enrich the surfaces of the blends. The relatively high PTFE content on the surface favored the formation of tribo-films, enhancing the tribological properties of the blends.

scholarly journals Effect of Reactive SPS on the Microstructure and Properties of a Dual-Phase Ni-Al Intermetallic Compound and Ni-Al-TiB2 Composite

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5668
Author(s):  
Paweł Hyjek ◽  
Iwona Sulima ◽  
Piotr Malczewski ◽  
Krzysztof Bryła ◽  
Lucyna Jaworska
Keyword(s):  
Intermetallic Compound ◽  
Tribological Properties ◽  
Matrix Material ◽  
Dual Phase ◽  
Compression Tests ◽  
Two Phase ◽  
Alloy Matrix ◽  
Plastic Properties ◽  
Mechanical And Tribological Properties ◽  
The Matrix

As part of the tests, a two-phase NiAl/Ni3Al alloy and a composite based on this alloy with 4 vol% addition of TiB2 were produced by the reactive FAST/SPS (Field Assisted Sintering Technology/Spark Plasma Sintering) sintering method. The sintering process was carried out at 1273 K for 30 s under an argon atmosphere. The effect of reactive SPS on the density, microstructure, and mechanical and tribological properties of a dual-phase Ni-Al intermetallic compound and Ni-Al-TiB2 composite was investigated. Products obtained were characterized by a high degree of sintering (over 99% of the theoretical density). The microstructure of sinters was characterized by a large diversity, mainly in regard to the structure of the dual-phase alloy (matrix). Compression tests showed satisfactory plastic properties of the manufactured materials, especially at high temperature (1073 K). For both materials at room temperature, the compressive strength was over 3 GPa. The stress–strain curves were observed to assume a different course for the matrix material and composite material, including differences in the maximum plastic flow stress depending on the test temperature. The brittle-to-ductile transition temperature was determined to be above 873 K. The research has revealed differences in the physical, mechanical and tribological properties of the produced sinters. However, the differences favourable for the composite were mostly the result of the addition of TiB2 ceramic particles uniformly distributed on grain boundaries.

The synergistic effect of SiC/R-GO composite on mechanical and tribological properties of thermosetting polyimide

2021 ◽  
pp. 002199832110492
Author(s):  
Aijiao Li ◽  
Suoxiao Wang ◽  
Zhe Chen ◽  
Hong Liu ◽  
Hongding Wang
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Tribological Properties ◽  
High Performance ◽  
In Situ Polymerization ◽  
Effective Means ◽  
Compression Modulus ◽  
Nanocomposite Films ◽  
Mechanical And Tribological Properties ◽  
Industry Applications

The effective means to solve material wear is to develop self-lubricating composite materials with excellent tribological, thermal, and mechanical properties. Herein, the composites of reduced graphene oxide (r-GO) nanosheet decorated with Silicon Carbide (SiC) were facilely prepared with employing a silane coupling agent, and the corresponding r-GO/SiC/thermosetting polyimide (r-GO/SiC/TPI) nanocomposite films were obtained by in situ polymerization method. The mechanical, tribological, and thermal properties of these nanocomposite films were investigated. When the content of r-GO/SiC was at 1.0 wt%, the compression strength and compression modulus of the composite increased by 37.7% and 47.3%, respectively, which were much higher than that of TPI composites addition of r-GO or SiC alone. Furthermore, r-GO/SiC/TPI composites also exhibited the lowest wear rate and friction coefficient in these reinforced TPI nanocomposites. When the content of r-GO/SiC was 0.8 wt%, particularly, the friction coefficient and wear rate of r-GO/SiC/TPI decreased by 22.8% and 79.8% compared to pure TPI, respectively. Additionally, trace amount r-GO/SiC hybrids also significantly enhance the thermal stability of TPI matrix. Compared to the polyimide composites reinforced by common nano-scale inorganic fillers, the outstanding mechanical and tribological properties of this r-GO/SiC/PI composites could be attributed to the ball on plane structure of GO/SiC, which lead to crack reflection, strength increment. These r-GO/SiC/TPI composites demonstrate the promising potential to be used as high-performance tribological materials in industry applications.

The Research on the Tribological Properties of C/C Composites

2011 ◽  
Vol 287-290 ◽  
pp. 675-678 ◽  
Author(s):  
Wen Xia Wang
Keyword(s):  
Carbon Fiber ◽  
Tribological Properties ◽  
Thermal Gradient ◽  
High Performance ◽  
Sliding Wear ◽  
Chemical Vapor ◽  
Chemical Vapor Infiltration ◽  
Three Point Bending ◽  
Mechanical And Tribological Properties ◽  
Wear Tests

The mechanical and tribological behaviors of the carbon/carbon (C/C) composites were evaluated by three-point bending and sliding wear tests. The effect of carbon fiber content on their mechanical behavior was also investigated. To produce the C/C composites, the precursor was introduced to the preforms by impregnating with phenolic solution. The C/C preforms were densified by thermal gradient chemical vapor infiltration. Results indicated that, the C/C composites show excellent mechanical and tribological properties. A kind of high performance brake materials was obtained.

Sign in / Sign up

Export Citation Format

Share Document