scholarly journals Improvement on Mechanical Properties of Fresh and Hardened Concrete by Marble Waste and Pumicite

2019 ◽  
Vol 9 (2) ◽  
pp. 2976-2979
Keyword(s):  
Tensile Strength ◽  
Sustainable Growth ◽  
Experimental Investigations ◽  
Hardened Concrete ◽  
Infrastructure Development ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
Fine Aggregates ◽  
General Improvement ◽  
Marble Powder

Development, world-over is fuelled by growth of the economy and the growth of economy is fuelled by growth in infrastructure. Estimates record a consumption of 6.6 Gigatonnes of concrete in China in earlier part of this decade, for infrastructure development. But today the world is poised on a tipping point environmentally, and sustainable growth is the need of the hour. This requirement is leading to research in replacement of energy intensive materials, along with capture and utilization of available waste. Marble powder waste which has deleterious impact on environment is one such material. Existing literature majorly focus on utilization of marble powder as fine aggregates in concrete. This study aims to study the suitability of marble powder as a filler material and as a replacement of cement. Pumice breccias are used as coarse aggregates. Experimental investigations were conducted to ascertain the compressive and split tensile strength in concrete with marble powder replacing cement by various percentages. The results indicate a general improvement in both compressive and split tensile strength.

scholarly journals Effect of Design Parameters on Compressive and Split Tensile Strength of Self-Compacting Concrete with Recycled Aggregate: An Overview

2021 ◽  
Vol 11 (13) ◽  
pp. 6028
Author(s):  
P. Jagadesh ◽  
Andrés Juan-Valdés ◽  
M. Ignacio Guerra-Romero ◽  
Julia M. Morán-del Morán-del Pozo ◽  
Julia García-González ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Design Parameters ◽  
Fine Aggregate ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
Fine Aggregates

One of the prime objectives of this review is to understand the role of design parameters on the mechanical properties (Compressive and split tensile strength) of Self-Compacting Concrete (SCC) with recycled aggregates (Recycled Coarse Aggregates (RCA) and Recycled Fine Aggregates (RFA)). The design parameters considered for review are Water to Cement (W/C) ratio, Water to Binder (W/B) ratio, Total Aggregates to Cement (TA/C) ratio, Fine Aggregate to Coarse Aggregate (FA/CA) ratio, Water to Solid (W/S) ratio in percentage, superplasticizer (SP) content (kg/cu.m), replacement percentage of RCA, and replacement percentage of RFA. It is observed that with respect to different grades of SCC, designed parameters affect the mechanical properties of SCC with recycled aggregates.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals Compression and Split Tensile Characteristics of Concrete Containing Quarry Residues

2019 ◽  
Vol 5 (5) ◽  
pp. 1-5
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Research Facility ◽  
River Sand ◽  
Split Tensile Strength ◽  
Fine Aggregates ◽  
Concrete Production ◽  
The World ◽  
Substitute Material ◽  
Quarry Dust

Waterway sand and pit sand are the most normally utilized fine aggregates for concrete creation in many parts of the world. Huge scale extraction of these materials presents genuine ecological risk in numerous parts of the nation. Aside from the ecological danger, there still exists the issue of intense lack in many regions. In this way, substitute material in place of river sand for concrete production should be considered. The paper means to examine the compressive and split tensile qualities of concrete produced using quarry residue, sand, and a blend of sand and quarry dust. The experimentation is absolutely research facility based. A total of 60 concrete cubes of size 150 mm x 150 mm x 150 mm, and 60 cylinders 150 mm in diameter and 300 mm deep, conforming to M50 grade were casted. All the samples were cured and tested with a steady water/concrete proportion of 0.31. Out of the 60 blocks cast, 20 each were made out of natural river sand, quarry dust and an equivalent blend of sand and quarry dust. It was discovered that the compressive strength and split tensile strength of concrete produced using the blend of quarry residue and sand was higher than the compressive qualities of concrete produced using 100% sand and 100% quarry dust.

scholarly journals Optimizing the Tensile Strength of Polystyrene Lightweight Concrete: A Panacea for Sustainable Housing Development in Developing Countries

2021 ◽  
pp. 107-125
Author(s):  
S. E. Ubi
Keyword(s):  
Tensile Strength ◽  
Large Scale ◽  
Building Blocks ◽  
Expanded Polystyrene ◽  
Partial Replacement ◽  
Split Tensile Strength ◽  
Polystyrene Beads ◽  
Coarse Aggregates ◽  
Lattice Design ◽  
Strength Result

The use of polystyrene beads in concrete applications has been limited due to its perceived low strength properties. Tensile strength test is an important test that determines the vulnerability of concrete to tensile cracking due to the weight of the structural load. Water, sand, coarse aggregates, expanded polystyrene beads, and ordinary Portland cement are the materials used for this study. All the materials were batched according to their weight, except for polystyrene and coarse aggregates which were batched in volume after mixing them together. The polystyrene partial replacement level was considered at 12% of the coarse aggregate volume. The model equation adopted for this study was based on Scheffe’s {4, 2} simplex lattice design for both Pseudo component and component proportional models. The actual model was developed from the 28th day test result. The Mathlab and Minitab 16 software were used in this study to generate the actual mix ratios. The results obtained showed that both Pseudo component and component proportional models both produced an average split tensile strength of about 5.10N/mm2. This implied that the results of this study produced a split tensile strength result that varied between 18% - 19% of its compressive strength result. This showed that the materials and the mix ratios optimized in this study are suitable as building blocks for residential low rising buildings and as partition slaps for high rising buildings. The lightweight property makes it highly suitable for large scale application in high rising structures as internal partition slaps only.

Effect of Mixing Steel Dust and Shred-Like Steel Fibres on the Properties of Concrete

2019 ◽  
Vol 7 (1) ◽  
pp. 24-29
Author(s):  
A. Ajwad ◽  
N. Khadim ◽  
Abdullah ◽  
U. Ilyas ◽  
M. U. Rashid ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Strength Test ◽  
Hardened Concrete ◽  
Normal Concrete ◽  
Steel Fibres ◽  
Coarse Aggregates ◽  
Mix Proportion ◽  
Steel Dust

In this research, fine and coarse aggregates present in the concrete are replaced with steel dust and shred-like steel fibres, respectively in different ratios and its effect on the properties of concrete is studied. Eight batches of concrete were mixed, each with the mix proportion of 1:2:4 and water cement ratio of 0.52. Batch A was of normal concrete. In batches B, C, and D, 5%, 10%, and 15% of sand was replaced with steel dust. In batches, E, F, and G, 2%, 5%, and 8% of coarse aggregate were replaced with steel fibres. In the last batch H, both 5% of sand and 5% of coarse aggregate were replaced with steel fine and steel fibres respectively. British as well as American standards were followed during the research. Slump test was performed in a fresh state of each mix to find the effect of these replacements on workability. 12 cubes of 150mm x 150mm x 150mm for compressive strength test and 12 cylinders of 150mm diameter and 300mm height of each, for tensile strength test were made for each batch to check these strength after 3, 7, 14, 28 days. It was found that the workability of fresh concrete decreases while density of fresh as well as hardened concrete increases with these replacements. It also results in an increase in initial compressive strength and a decrease in final compressive strength as compared to those of normal concrete. As far as tensile strength is concerned an increase in initial as well as final strength was observed.

scholarly journals Lightweight concrete with Algerian limestone dust. Part II: study on 50% and 100% replacement to normal aggregate at timely age

Cerâmica ◽  
2015 ◽  
Vol 61 (360) ◽  
pp. 462-468 ◽  
Author(s):  
S. Kitouni ◽  
H. Houari
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Relative Humidity ◽  
Lightweight Concrete ◽  
Environmental Concern ◽  
Hardened Concrete ◽  
Dead Weight ◽  
Coarse Aggregates ◽  
Strength Tests ◽  
Limestone Dust

Abstract A control lightweight concrete (LWC) mixture made with 50% and 100% of limestone as a replacement of coarse aggregates in weight was prepared. Limestone is used for economical and environmental concern. The concrete samples were cured at 65% relative humidity at 20 ºC. The compressive and flexural tensile strengths, elastic modulus and Poisson's ratio of hardened concrete were measured. Laboratory compressive and tensile strength tests results showed that LWC can be produced by the use of limestone. The aim of this study is twofold: one is to design a lightweight concrete with the use of limestone that will provide an advantage of reduction in dead weight of a structure; and second is to obtain a more economical LWC mixture with the use of limestone.

scholarly journals An Experimental Research On Partial Replacement Of Coarse Aggregate with Recycled Aggregate and Fine Aggregate with Granite Powder

2019 ◽  
Vol 8 (9S2) ◽  
pp. 72-77
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Age Group ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
Granite Powder

Now a days increase in population increases the demand of concrete for construction purpose and Aggregates are the important constituents in concrete.Re-use of demoliation waste avoids the problem of waste disposal and is also helpful in reducing the gap between demand and supply of fresh aggregates. This research deals with partial replacement of natural coarse aggregates (NCA) with recycled coarse aggregates (RCA) of age group 30 years and 35 years in different proportions like 20%, 30%, 40% . For this, M20 grade of concrete is adopted. Curing of specimens were done for 7days and 28 days to attain the maximum strengths. Partial replacement of fine aggregate with Granite powder at 5%, 10%, 15% were done to reduce the waste percentage as well to gain more strength. After casting the specimens of RCA with Granite powder replacement, curing was done and the specimens were tested for compressive and tensile strengths. Obtained results of compressive and tensile strengths of RCA concrete mix were compared with conventional concrete. In this direction, an experimental investigation of compressive and tensile strength was undertaken to use RCA as a partial replacement in concrete. It was observed that the concrete with recycled aggregates of 30years and 35years age group achieved maximum compressive strength of 29.03 N/mm2 , 28.96 N/mm2 and tensile strength of 11.91 N/mm2 , 10.34 N/mm2 were obtained at 40%replacement of RCA respectively. It is found that the compressive strength and Split tensile strength of RAC with copper slag was increased 8.20% and 2.90% when compared with the RAC.

scholarly journals Influence of Coarse Aggregate Gradation on the Mechnical Properties of Concrete, Part II: No-Fines Vs. Ordinary Concrete

2019 ◽  
Vol 9 (5) ◽  
pp. 4623-4626
Author(s):  
A. S. Buller ◽  
Z. A. Tunio ◽  
F. U. R. Abro ◽  
T. Ali ◽  
K. A. Jamali
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Coarse Aggregate ◽  
Substantial Effect ◽  
Strength Properties ◽  
Minimum Size ◽  
Split Tensile Strength ◽  
Aggregate Gradation ◽  
Coarse Aggregates ◽  
Water Curing

This study aims to investigate the effect of different gradations of coarse aggregates on mechanical properties of no-fines concrete (NFC). NFC reduces a structure’s self-weight, thus minimizing cost. The effects of coarse aggregate gradation on mechanical properties such as compressive strength, split tensile strength, and flexural strength were studied and compared at the end of 28-day water curing. A fixed cement- to-aggregate proportion 1:6 with 0.5 water/cement (w/c) ratio was adopted. Four gradations of coarse aggregates ranging between specific maximum and minimum size were used, namely 5mm-4mm, 10mm-4mm, 20mm-4mm and 20mm-15mm. The results of this study reveal the substantial effect of the gradation of coarse aggregates on strength properties compressive and tensile strength of NFC.

scholarly journals Effect of Sugarcane Bagasse Ash and Lime Stone Fines on the Mechanical Properties of Concrete

2020 ◽  
Vol 10 (2) ◽  
pp. 5534-5537 ◽  
Author(s):  
N. Bheel ◽  
A. S. Memon ◽  
I. A. Khaskheli ◽  
N. M. Talpur ◽  
S. M. Talpur ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Energy Consumption ◽  
Sugarcane Bagasse ◽  
Hardened Concrete ◽  
Split Tensile Strength ◽  
Cement Production ◽  
Optimum Result ◽  
Mix Proportion ◽  
Sugarcane Bagasse Ash ◽  
Limestone Fines

Cement production releases huge amounts of carbon dioxide having a significant impact on the environment while also having huge energy consumption demands. In addition, the disposal and recovery of natural concrete components can lead to environmental degradation. The use of waste in concrete not only reduces cement production, but it also reduces energy consumption. The aim of this study is to evaluate the properties of fresh and hardened concrete by partially replacing cement with sugarcane bagasse ash (SCBA) and limestone fines (LSF). In this investigation work the cement was replaced with SCBA ash and LSF by 0% (0% SCBA+ 0% LSF), 5% (2.5% SCBA+ 2.5% LSF), 10% (5% SCBA+ 5% LSF), 15% (7.5% SCBA+ 7.5% LSF) and 20% (10% SCBA+ 10% LSF) by weight of cement. In this regard, a total of 60 samples of concrete specimens were made with mix proportion of 1:1.5:3 with 0.56 water-cement ratio. Cube specimens were tested for compressive strength and cylindrical specimens were used for determining splitting tensile strength at 7 and 28 days respectively. The optimum result displayed that the crushing strength and split tensile strength increased by 10.33% and 10.10% while using 5% SCBA+ 5% LSF as a substitute for cement in concrete after the 28th day. The slump value of concrete declined as the content of SCBA and LSF increased.

Sign in / Sign up

Export Citation Format

Share Document