scholarly journals Design, Simulation and Experimental Analysis on Rectangular Microstrip Patch Antenna with Superstrates

2020 ◽  
Vol 9 (3) ◽  
pp. 3641-3645
Keyword(s):  
Experimental Analysis ◽  
High Frequency ◽  
Return Loss ◽  
Simulation Software ◽  
Center Frequency ◽  
Transmission Line Model ◽  
Frequency Range ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Optimum Height

This paper focuses on design, simulation and experimental analysis of rectangular MSA with and without superstrates. The rectangular MPA is designed at frequency range of 2.40 GHz, which is lying in the S band region. The transmission line model analysis and High Frequency Simulation Software (HFSS) is used for designing of proposed rectangular MPA. The proposed antenna is fabricated on Arlon diclad 880 substrate, whose dielectric constant is 2.2, thickness of the substrate is 1.6mm and loss tangent is 0.0009. In this paper the effect of dielectric superstrates on rectangular MPA and the height of superstrate are varying above the rectangular MPA is investigated experimentally and compared with simulated and measured results. The proposed antenna has been analyzed using different dielectric superstrates. From the study it was observed that in antenna without superstrate the VSWR is 1.21, return loss is -18.51dB, bandwidth is 0.038GHz. However, gain is 8.77dB. In the antennas with superstrates, center frequency is shifted from 2.40 GHz to 2.33 GHz as well as other parameters are slightly degraded. As superstrate height increases, the performance antenna is degraded and at particular optimum height the performance characteristics of antenna with and without superstrate will be same. The frequency range 2.40 GHz is used in wireless applications.

scholarly journals Band notched self complementaryultra wideband antenna for wireless applications

2018 ◽  
Vol 7 (2.8) ◽  
pp. 529 ◽  
Author(s):  
Ch Ramakrishna ◽  
G A.E.Satish Kumar ◽  
P Chandra Sekhar Reddy
Keyword(s):  
High Frequency ◽  
Return Loss ◽  
Wide Band ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Relative Dielectric Permittivity ◽  
Frequency Range ◽  
Ground Structure ◽  
Wireless Applications ◽  
Patch Edge

This paper presents a band notched WLAN self complementaryultra wide band antenna for wireless applications. The proposed antenna encounters a return loss (RL) less than -10dB for entire ultra wideband frequency range except band notched frequency. This paper proposes a hexagon shape patch, edge feeding, self complementary technique and defective ground structure. The antenna has an overall dimensionof 28.3mm × 40mm × 2mm, builton  substrate FR4 with a relative dielectric permittivity 4.4. And framework is simulated finite element method with help of high frequency structured simulator HFSSv17.2.the proposed antenna achieves a impedance bandwidth of 8.6GHz,  band rejected WLAN frequency range 5.6-6.5 GHz with  vswr is less than 2.

Wide-stopband bandpass-filtering power divider with high-frequency selectivity

2017 ◽  
Vol 9 (10) ◽  
pp. 1931-1936 ◽  
Author(s):  
Kaijun Song ◽  
Yifang Zhou ◽  
Maoyu Fan ◽  
Yu Zhu ◽  
Yong Fan
Keyword(s):  
Insertion Loss ◽  
High Frequency ◽  
Return Loss ◽  
Signal Transmission ◽  
Frequency Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Frequency Range ◽  
Transmission Zeros ◽  
Stopband Attenuation

A wide-stopband bandpass-filtering power divider with high-frequency selectivity has been proposed in this paper. The input and output feeding lines and eight 1/4 wavelength resonators are used to realize the signal transmission. In order to obtain good frequency selectivity, source-load coupling transmission path is used to generate transmission zeros near the passband. A four-way power divider with bandpass-filtering response and high-frequency selectivity is designed, fabricated, and measured. The measured results agree with the simulated ones closely in the desirable frequency range. The measured center frequency of the power divider is 2.38 GHz with input return loss of 31.2 dB, while the measured insertion loss is about 1 dB (not including ideal 6 dB four-way power dividing insertion loss). Moreover, the measured 3-dB bandwidth is 12% and the measured stopband attenuation is >15 dB from 2.59 to 7.7 GHz. In addition, two transmission zeros of 1.9 and 2.8 GHz are located near the passband. The measured output isolations are all >15.7 dB.

scholarly journals Broadband microstrip patch antenna at 28 GHz for 5G wireless applications

2021 ◽  
Vol 11 (3) ◽  
pp. 2238
Author(s):  
Kinde Anlay Fante ◽  
Mulugeta Tegegn Gemeda
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Substrate Material ◽  
Microstrip Patch Antenna ◽  
Radiation Efficiency ◽  
Center Frequency ◽  
Sidelobe Level ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Improved Performance

In this paper, a 28 GHz broadband microstrip patch antenna (MSPA) for 5G wireless applications is presented. The Rogers RT/Duroid5880 substrate material, with a dielectric constant of 2.2, the thickness of 0.3451 mm, and loss tangent of 0.0009, is used for the studied antenna to operate at 28 GHz center frequency. The proposed design of antenna is simulated by using CST studio suite. The simulation results highlight that the studied antenna has a return loss of -54.49 dB, a bandwidth of 1.062 GHz, a gain of 7.554 dBi. Besides, radiation efficiency and the sidelobe level of the proposed MSPA are 98% and 18.4 dB, respectively. As compared to previous MSPA designs reported in the recent scientific literature, the proposed rectangular MSPA has achieved significantly improved performance in terms of the bandwidth, beam-gain, return loss, sidelobe level, and radiation efficiency. Hence, it is a potential contender antenna type for emerging 5G wireless communication applications.

scholarly journals Designing a Microstrip Patch Antenna in Part of Ultra-Wideband Applications

2020 ◽  
Vol 17 (4) ◽  
pp. 1216
Author(s):  
Wa'il A. Godaymi Al-Tumah ◽  
Raed Shaaban ◽  
Zeki Ahmed
Keyword(s):  
High Frequency ◽  
Microstrip Antenna ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Ultra Wideband ◽  
Frequency Range ◽  
High Frequency Structure Simulator ◽  
Microstrip Patch ◽  
Rectangular Patch ◽  
Rectangular Microstrip Antenna

In this work, a simulated study was carried out for designing a novel spiral rectangular patch of microstrip antenna that is used in ultra-wideband applications by using a high frequency structure simulator software (HFSS). A substrate with dielectric constant of 4.4 and height 2.10 mm (commercial substrate height available is about 0.8-1.575 mm) has been used for the design of the proposed antenna. The design basis for enhancing bandwidth in the frequency range 6.63 - 10.93 GHz is based on increasing the edge areas that positively affect the antenna's efficiency. This design makes the designed antenna cost less by reducing the area of the patch. It has been noticed that the bandwidth of the antenna under this study is increasing to 4.30 GHz or 61% compared with 3.6% for the standard rectangular microstrip antenna with the same dimensions of the proposed antenna. The antenna also maintains the voltage standing wave ratio of 1.09 at resonant frequency 7.07 GHz, return loss -27.07 dB, and the amount of impedance in real and imaginary parts 51.5Ω and 3.3Ω, respectively.

scholarly journals A Novel Frequency Reconfigurable Microstrip Patch Antenna using Pin Diode

2020 ◽  
Vol 9 (5) ◽  
pp. 2013-2017
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Pin Diode ◽  
Optimum Level ◽  
Frequency Range ◽  
Microstrip Patch ◽  
Single Antenna ◽  
Specific Frequency ◽  
Switching State

In recent study, in the growth of wireless technology single antenna that works with a specific frequency is becoming outdated. The antenna which is capable to work dynamically is encouraged. To make an antenna to work dynamically, modification in any of the antenna characteristics can be applied. In this proposed work, the antenna which can reconfigure its frequency is designed and analyzed. Microstrip patch antenna is most popular printed type antenna which is suitable for diverse applications. The antenna design consists of three PIN diodes which are placed in different positions on the patch. Depending upon the switching state of PIN diode the antenna can operate in different frequency ranges. The frequency range obtained ranges from 1.38 GHz to 3.24 GHz. Return loss value, VSWR obtained is of optimum level. The various gain of antenna is obtained in simulation. The analysis of the antenna is done in ANSYS HFSS software.

scholarly journals Gain Enhancement of Microstrip Antenna using Ebg Structure for Wi-Fi Application

2019 ◽  
Vol 9 (1) ◽  
pp. 1213-1217
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Single Frequency ◽  
Total Size ◽  
Compact Structure ◽  
Gain Enhancement ◽  
Microstrip Patch ◽  
Low Profile

A microstrip patch antenna is low profile antenna mounted over a high impedance electromagnetic bandgap (EBG) substrate is proposed. In this paper, Microstrip patch antenna with rectangular EBG structure is proposed and studied. The proposed antenna has compact structure with a total size of 29.44x38.036mm2 . The designed antenna resonates at Particular Single frequency with improved return loss, VSWR and gain. The resonant frequency of the antenna 2.4GHz without and with EBG and improved return loss of -17.61dB and -18.30dB. With rectangular EBG the antenna gives improved gain of 2.09 dB. The Proposed antenna is simulated by using Simulation software ie.(IE3D) and simulated results are in good with practical antenna characteristics.

A Low Loss Fully Embedded Stripline Parallel Coupled BPF for Applications using the 60 GHz Band

2011 ◽  
Vol 2011 (CICMT) ◽  
pp. 000050-000053
Author(s):  
Alexander Schulz ◽  
Sven Rentsch ◽  
Lei Xia ◽  
Robert Mueller ◽  
Jens Mueller
Keyword(s):  
Return Loss ◽  
Bandpass Filter ◽  
Coplanar Waveguide ◽  
Center Frequency ◽  
60 Ghz ◽  
Low Loss ◽  
Wireless Applications ◽  
High Data ◽  
V Band ◽  
Waveguide Transmission

This paper presents a low loss fully embedded bandpass filter (BPF) using low temperature co-fired ceramic (LTCC) for multilayer System-in-Package (SiP) and Multi-Chip-Module (MCM) applications, e.g. wireless applications for the unlicensed 60 GHz band. The measured insertion loss was 1.5 dB at the center frequency 58 GHz, and a return loss of less than −10 dB was achieved, including two grounded coplanar waveguide transmission line (CPWg) to stripline transitions. The four layers BPF has a 3 dB bandwidth of about 11 GHz which supplies e.g. broadband and high data rate applications. The whole BPF requires a substrate area of 5.6 × 2.1 × 0.42 mm3 with transitions and a shielding via fence. This BPF suits well for V-band applications in a LTCC package because of the compact dimensions and the good performance.

Dual-Band Proximity Coupled Feed Microstrip Patch Antenna with ‘T’ Slot on the Radiating Patch and ‘Dumbbell’ Shaped Defected Ground Structure

2016 ◽  
Vol 3 (2) ◽  
pp. 435 ◽  
Author(s):  
Dawit Fitsum ◽  
Dilip Mali ◽  
Mohammed Ismail
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Microstrip Patch Antenna ◽  
Dual Band ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Rectangular Microstrip Patch Antenna

<p>This paper presents Dual-Band proximity coupled feed rectangular Microstrip patch antenna with slots on the radiating patch and Defected Ground Structure. Initially a simple proximity coupled feed rectangular Microstrip patch antenna resonating at 2.4 GHz is designed. Etching out a ‘Dumbbell’ shaped defect from the ground plane and ‘T’ shaped slot from the radiating patch of the proximity coupled feed rectangular Microstrip patch antenna, results in a Dual-Band operation, i.e., resonating at 2.4 GHz and 4.5 GHz; with 30.3 % and 18.8% reduction in the overall area of the patch and the ground plane of the reference antenna respectively. The proposed antenna resonates in S-band at frequency of 2.4 GHz with bandwidth of 123.6 MHz and C-band at frequency of 4.5 GHz with bandwidth of 200 MHz, and a very good return loss of -22.1818 dB and -19.0839 dB at resonant frequency of 2.4 GHz and 4.5 GHz respectively is obtained. The proposed antenna is useful for different wireless applications in the S-band and C-band.</p>

Circularly Polarized Rectangular Microstrip Patch Antenna with Finite Ground Plane

2015 ◽  
Vol 4 (2) ◽  
pp. 74
Author(s):  
Sanyog Rawat ◽  
Kamlesh Kumar Sharma
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Axial Ratio ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Microstrip Patch ◽  
Rectangular Patch

<p class="Abstract"><span style="font-weight: normal;">In this paper a new geometry of patch antenna is proposed with improved bandwidth and circular polarization. The radiation performance of circularly polarized rectangular patch antenna is investigated by applying IE3D simulation software and its performance is compared with that of conventional rectangular patch antenna.</span> <span style="font-weight: normal;">Finite Ground truncation technique is used to obtain the desired results. The simulated return loss, axial ratio and smith chart with frequency for the proposed antenna is reported in this paper. It is shown that by selecting suitable ground-plane dimensions, air gap and location of the slits, the impedance bandwidth can be enhanced upto 10.15 % as compared to conventional rectangular patch (4.24%) with an axial ratio bandwidth of 4.05%.</span></p><p> </p><p> </p>

scholarly journals Performance Comparison of Swastika and Rectangular Shaped Microstrip Patch Antenna

2018 ◽  
Vol 1 (1) ◽  
pp. 11-14
Author(s):  
Suroj Burlakoti ◽  
Prakash Rai
Keyword(s):  
Radiation Pattern ◽  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Performance Comparison ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Patch Antennas ◽  
Microstrip Patch Antennas ◽  
Microstrip Patch

In this paper, Microstrip patch antennas with rectangular and swastika shape of patch are designed and its performance parameters are compared with each other. Rectangular and Swastika shaped patch are considered in this paper with common rectangular ground plane. The antenna is simulated at 2.4 GHz using HFSS simulation software. This work mainly includes modification of antenna patch to improve the antenna parameters. The parameters of antenna such as Return loss, VSWR Bandwidth and radiation pattern are compared using simulation. The performance of Swastika shaped antenna was found to be better than rectangular shaped microstrip patch antenna with improved Return Loss, VSWR, Bandwidth and Radiation Pattern.

Sign in / Sign up

Export Citation Format

Share Document