A Low Loss Fully Embedded Stripline Parallel Coupled BPF for Applications using the 60 GHz Band

2011 ◽  
Vol 2011 (CICMT) ◽  
pp. 000050-000053
Author(s):  
Alexander Schulz ◽  
Sven Rentsch ◽  
Lei Xia ◽  
Robert Mueller ◽  
Jens Mueller
Keyword(s):  
Return Loss ◽  
Bandpass Filter ◽  
Coplanar Waveguide ◽  
Center Frequency ◽  
60 Ghz ◽  
Low Loss ◽  
Wireless Applications ◽  
High Data ◽  
V Band ◽  
Waveguide Transmission

This paper presents a low loss fully embedded bandpass filter (BPF) using low temperature co-fired ceramic (LTCC) for multilayer System-in-Package (SiP) and Multi-Chip-Module (MCM) applications, e.g. wireless applications for the unlicensed 60 GHz band. The measured insertion loss was 1.5 dB at the center frequency 58 GHz, and a return loss of less than −10 dB was achieved, including two grounded coplanar waveguide transmission line (CPWg) to stripline transitions. The four layers BPF has a 3 dB bandwidth of about 11 GHz which supplies e.g. broadband and high data rate applications. The whole BPF requires a substrate area of 5.6 × 2.1 × 0.42 mm3 with transitions and a shielding via fence. This BPF suits well for V-band applications in a LTCC package because of the compact dimensions and the good performance.

A comparative study on four different transmission lines in LTCC for 60 GHz applications

2016 ◽  
Vol 2016 (CICMT) ◽  
pp. 000191-000198 ◽  
Author(s):  
A. Isapour ◽  
D. Bahloul ◽  
A. B. Kouki
Keyword(s):  
Transmission Lines ◽  
Coplanar Waveguide ◽  
Data Rate ◽  
High Data Rate ◽  
60 Ghz ◽  
Low Loss ◽  
Great Opportunity ◽  
High Data ◽  
Wireless Telecommunication ◽  
5 Ghz

Abstract The wireless telecommunication systems have an undeniable role in today's society. The rapid progress of wireless services and applications accelerates demands for high data-rate reliable systems. The 60 GHz band with its 5 GHz globally unlicensed available spectrum, provides a great opportunity for the next generation of high data-rate wireless communication. Despite this attractive bandwidth surrounding 60 GHz, there are still many challenges to be addressed such as the loss performance and the integration with other systems. Low Temperature Cofired Ceramic (LTCC) technology, with its unique and mature multilayer fabrication process, has excellent capability of realizing miniaturized 3D low loss structures to overcome these challenges. Since, one of the key components in any communication system for both interconnecting and designing components is Low loss transmission lines, in this article we overview the performances and challenges for four different most practical transmission lines at 60 GHz in LTCC: Microstrip, Stripline, Coplanar Waveguide (CPW), and LTCC Integrated Waveguide (LIW).

CPW-fed concurrent, dual band planar antenna for millimeter wave applications

2018 ◽  
Vol 10 (9) ◽  
pp. 1088-1095
Author(s):  
Smriti Agarwal ◽  
Dharmendra Singh
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Cost Effective ◽  
Dual Band ◽  
Single Frequency ◽  
60 Ghz ◽  
Fractional Bandwidth ◽  
High Data ◽  
V Band ◽  
Dual Band Antenna

AbstractIn recent years, millimeter wave (MMW) has received tremendous interest among researchers, which offers systems with high data rate communication, portability, and finer resolution. The design of the antenna at MMWs is challenging as it suffers from fabrication and measurement complexities due to associated smaller dimensions. Current state-of-the-art MMW dual-band antenna techniques demand high precision fabrication, which increases the overall cost of the system. Henceforth, the design of an MMW antenna with fabrication and measurement simplicity is quite challenging. In this paper, a simple coplanar waveguide (CPW) fed single-band MMW antenna operating at 94 GHz (W band) and a dual-band MMW antenna operating concurrently at 60 GHz (V band) and 86 GHz (E band) have been designed, fabricated, and measured. A 50 Ω CPW-to-microstrip transition has also been designed to facilitate probe measurement compatibility and to provide proper feeding to the antenna. The fabricated single frequency 94 GHz antenna shows a fractional bandwidth of 11.2% andE-plane (H-plane) gain 6.17 dBi (6.2 dBi). Furthermore, the designed MMW dual-band antenna shows fractional bandwidth: 2/6.4%, andE-plane (H-plane) gain: 7.29 dBi (7.36 dBi)/8.73 dBi (8.68 dBi) at 60/86 GHz, respectively. The proposed antenna provides a simple and cost-effective solution for different MMW applications.

Coplanar waveguide-fed ISM band implantable crossed-type triangular slot antenna for biomedical applications

2013 ◽  
Vol 6 (2) ◽  
pp. 167-172 ◽  
Author(s):  
Srinivasan Ashok Kumar ◽  
Thangavelu Shanmuganantham
Keyword(s):  
Biomedical Applications ◽  
Biomedical Application ◽  
Coplanar Waveguide ◽  
Impedance Matching ◽  
High Gain ◽  
Slot Antenna ◽  
Center Frequency ◽  
Ism Band ◽  
High Data ◽  
Implantable Antenna

A novel coplanar waveguide fed Industrial, Scientific, and Medical (ISM) band implantable crossed-type triangular slot antenna is proposed for biomedical applications. The antenna operates at the center frequency of 2450 MHz, which is in ISM band, to support GHz wideband communication for high-data rate implantable biomedical application. The size of the antenna is 78 mm3 (10 mm × 12 mm × 0.65 mm). The simulated and measured bandwidths are 7.9 and 8.2% at the resonant frequency of 2.45 GHz. The specific absorption rate distribution induced by the implantable antenna inside a human body tissue model is evaluated. The communication between the implanted antenna and external device is also examined. The proposed antenna has substantial merits such as miniaturization, lower return loss, better impedance matching, and high gain over other implanted antennas.

scholarly journals Sharp Skirt Dual-Mode Bandpass Filter with Overlay Plate to Control Upper Passband Edge

2019 ◽  
Vol 8 (6) ◽  
pp. 2357-2360
Keyword(s):  
Analytical Model ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Dual Mode ◽  
Rf Receivers ◽  
Attenuation Level ◽  
Frequency Selective ◽  
Fixed Center

This paper presents design and analytical model for Sharp Skirt Dual-Mode Bandpass Filter for RF receivers. Proposed filter is designed using open stub loaded H shaped resonator. Based on analytical model insertion loss S21 and return loss S11 for proposed filter are demonstrated. Inductive Overlaying plate is proposed to control upper passband edge of proposed filter to improve frequency selectivity with fixed center frequency. The proposed filter has sharp frequency selective range from 5.1GHz to 9.2GHz. With overlay plate, frequency selective range is tuned to 5.1GHz-8.6GHz. Without overlaying plate the proposed filter has return loss greater than 10dB and insertion loss of 0.7dB. Lower and upper passband edges are at 5.1GHz and 9.2GHz with attenuation level of 52dB and 54dB respectively. With overlaying plate, the filter has same S 11 and S 21 parameters, but upper passband edge is shifted from 9.2GHz to 8.6GHz

Inkjet and 3D Printing Technology for Fundamental Millimeter-Wave Wireless Packaging

2018 ◽  
Vol 15 (3) ◽  
pp. 101-106
Author(s):  
Bijan K. Tehrani ◽  
Ryan A. Bahr ◽  
Manos M. Tentzeris
Keyword(s):  
3D Printing ◽  
Millimeter Wave ◽  
Integrated Circuit ◽  
Coplanar Waveguide ◽  
Frequency Selective Surface ◽  
60 Ghz ◽  
Low Loss ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Application Specific

Abstract This article outlines the design, processing, and implementation of inkjet and 3D printing technologies for the development of fully printed, highly integrated millimeter-wave (mm-wave) wireless packages. The materials, tools, and processes of each technology are outlined and justified for their respective purposes. Inkjet-printed 3D interconnects directly interfacing a packaging substrate with an integrated circuit (IC) die are presented using printed dielectric ramps and coplanar waveguide transmission lines exhibiting low loss (.6–.8 dB/mm at 40 GHz). Stereolithography 3D printing is presented for the encapsulation of IC dice, enabling the application-specific integration of on-package structures, including dielectric lenses and frequency selective surface–based wireless filters. Finally, inkjet and 3D printing technology are combined to present sloped mm-wave interconnects through an encapsulant, or through mold vias, achieving a slope of up to 65° and low loss (.5–.6 dB/mm at 60 GHz). The combination of these additive techniques is highlighted for the development of scalable, application-specific wireless packages.

A new compact and miniaturized multiband uniplanar CPW-fed Monopole antenna with T-slot inverted for multiple wireless applications

2017 ◽  
Vol 9 (7) ◽  
pp. 1541-1545 ◽  
Author(s):  
Rachid Dakir ◽  
Jamal Zbitou ◽  
Ahmed Mouhsen ◽  
Abdelwahed Tribak ◽  
Angel Mediavilla Sanchez ◽  
...  
Keyword(s):  
Return Loss ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Configuration Design ◽  
Rectangular Slot ◽  
Wireless Applications ◽  
Compact Size ◽  
Feeding Technique ◽  
Wireless Application ◽  
Antenna Configuration

In this paper, the design of a new compact uniplanar coplanar waveguide-fed antenna for multiband wireless application is presented and investigated. This antenna has a compact size of 25 × 25 mm2 and consists of a three parallel stub optimized added on rectangular slot to the radiator patch and T-shaped which inverted in the ground plane. The final prototype antenna designing resonantes at frequency bands (2.4–2.9 GHz), (3.7–5.2 GHz), and (5.7–6 GHz) with a return loss less than −10 dB. Details of the antenna configuration, design, simulation, and experimental results are presented, investigated, and discussed. The compactness, simple feeding technique, and conception of the uniplanar design make it easy to be integrated within devices of multiples wireless applications.

scholarly journals New Design of 60 GHz MIMO 2x4 Patch Rectangular Antenna Array for Wireless Gigabit (Wi-Gig) Application

2019 ◽  
Vol 2 (1) ◽  
pp. 6-9
Author(s):  
Yusnita Rahayu
Keyword(s):  
Return Loss ◽  
Simulation Software ◽  
Propagation Loss ◽  
60 Ghz ◽  
Broad Bandwidth ◽  
High Data ◽  
Rectangular Patch ◽  
Fifth Generation ◽  
The World ◽  
Indoor And Outdoor

Nowadays, most antenna researchers over the world are focusing on the design of the antenna for the fifth generation (5G) application (indoor and outdoor). High intensive research on 60 GHz antenna for high data rate indoor communication is becoming a trending topic. The high propagation loss at this band is the most challenging. The antenna needs to have higher gain to overcome the loss. Such antenna designs have been proposed recently. This paper, a new MIMO 2x4 patch rectangular antenna operating at 60 GHz is designed for Wi-Gig application. The rectangular patch antenna has 1.75 mm x 1.54 mm of size, printed on Rogers Duroid RT 5880 substrate, the dielectric constant of 2.20 and loss tangent of 0,0009. The antenna was designed and simulated using CST simulation software.  The simulated return loss showed a very consistent characteristic. The return loss reached −30 dB at 60 GHz.  The broad bandwidth obtained is 4.3 GHz concerning -10 dB. The omnidirectional radiation pattern with 13.4 dBi of gain is obtained. This antenna meets the Wi-Gig requirement.

scholarly journals Design of High Gain Wearable Rectangular Microstrip Textile Antenna for Wireless Application

2020 ◽  
Vol 9 (5) ◽  
pp. 540-544
Keyword(s):  
Return Loss ◽  
Recent Decade ◽  
High Gain ◽  
Center Frequency ◽  
Body Area ◽  
Physical Size ◽  
Wireless Applications ◽  
Emergency Rescue ◽  
Textile Antenna ◽  
Wireless Application

Wireless body area networks have paying more attention in the recent decade. The microstrip textile antenna used for wireless applications (ISM Band) such as emergency rescue, health monitoring and medical care. In this paper, the square patch microstrip textile antenna is introduced which is mounted on the flexible jeans substrate. The physical size of the suggested/simulated textile antenna is 52.99 X 45.23 mm2 & the jean’s material is used as substrate with its relative permittivity of ɛr = 1.67. The proposed antenna is radiating at the center frequency of 2.45 GHz with a return loss of -15.76 dB & VSWR 1.389, the far field directivity of an antenna is 8.05 dBi at 2.45GHz. The designed antenna is wearable on the clothes because the use of textile material for antenna fabrication by keeping SAR at 1.6 W/Kg.

scholarly journals Enhanced Bandwidth of Band Pass Filter Using a Defected Microstrip Structure for Wideband Applications

2018 ◽  
Vol 8 (6) ◽  
pp. 5260 ◽  
Author(s):  
Sanae Azizi ◽  
Mustapha El Halaoui ◽  
Abdelmoumen Kaabal ◽  
Saida Ahyoud ◽  
Adel Asselman
Keyword(s):  
Bandpass Filter ◽  
Dielectric Substrate ◽  
Center Frequency ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Bandwidth Enhancement ◽  
Wireless Applications ◽  
Coupled Lines ◽  
Band Pass ◽  
Microstrip Structure

<p>In this paper, the bandwidth enhancement of bandpass filter (BPF) is proposed by utilizing defected microstrip structure (DMS). The initial micro strip BPF which is designed to have the bandwidth 1GHz with the center frequency of 3.5GHz is deployed on FR4 Epoxy dielectric substrate with overall size and thickness of 14mm x 24mm and 1.6mm, respectively. The proposed filter consists of two parallel coupled lines centred by ring-shaped, to enhance the bandwidth response, an attempt is carried out by applying DMS on the ligne center with a ring-shaped of initial filter. Here, the proposed DMS is constructed of the arrowhead dumbbell. Some parametrical studies to the DMS such as changing to obtain the optimum geometry of DMS with the desired bandwidth response. From the characterization result, it shows that the utilization of DMS on to the microstrip ligne of filter has widened 3dB bandwidth response up to 1.8GHz ranges from 2.55GHz to 4.35GHz yielding an enhanced wideband response for various wideband wireless applications.</p>

Inkjet and 3D Printing Technology for Fundamental Millimeter-Wave Wireless Packaging

2017 ◽  
Vol 2017 (1) ◽  
pp. 000252-000257 ◽  
Author(s):  
Bijan K. Tehrani ◽  
Ryan A. Bahr ◽  
Manos M. Tentzeris
Keyword(s):  
3D Printing ◽  
Millimeter Wave ◽  
Transmission Lines ◽  
Coplanar Waveguide ◽  
Frequency Selective Surface ◽  
60 Ghz ◽  
Low Loss ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Application Specific

Abstract This paper outlines the design, processing, and implementation of inkjet and 3D printing technologies for the development of fully-printed, highly-integrated millimeter-wave (mm-wave) wireless packages. The materials, tools, and processes of each technology are outlined and justified for their respective purposes. Inkjet-printed 3D interconnects directly interfacing a packaging substrate with an IC die are presented using printed dielectric ramps and coplanar waveguide (CPW) transmission lines exhibiting low loss (0.6–0.8 dB/mm at 40 GHz). Stereolithography (SLA) 3D printing is presented for the encapsulation of IC dies, enabling the application-specific integration of on-package structures, including dielectric lenses and frequency selective surface (FSS)-based wireless filters. Finally, inkjet and 3D printing technology are combined to present sloped mm-wave interconnects through an encapsulation, or through-mold vias (TMVs), achieving a slope up to 65° and low loss (0.5–0.6 dB/mm at 60 GHz). The combination of these additive techniques is highlighted for the development of scalable, application-specific wireless packages.

Sign in / Sign up

Export Citation Format

Share Document