scholarly journals Properties of Lightweight Matrix according to Different Types of Alkali Stimulants

2019 ◽  
Vol 8 (2S6) ◽  
pp. 106-111
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Ionization Degree ◽  
Different Types ◽  
The Matrix ◽  
In Fire ◽  
Furnace Slag ◽  
Measuring Ph ◽  
Main Material

Recently, lightweight wall systems have been used mainly due to the appearance of flexible buildings, but EPS, which is flammable, is the main material. The damage caused by toxic gas in fire is recognized as a problem. NaOH, KOH and Ca(OH)2 were used as alkali stimulants and the properties of the matrix were evaluated according to the addition ratio of alkali stimulants. The addition of an alkali stimulant increases the pH and increases the alkali activity of the blast furnace slag, thereby changing the performance of the matrix. When NaOH and KOH are used as alkali stimulants, the density of the cured product is low and the incidence of the internal void of the cured product is high. When Ca(OH)2 is used as an alkali stimulant, it shows the best performance when measuring pH, setting time, and strength. This seems to be due to the ionization degree of the (OH) group. However, the incidence of voids was the lowest. When NaOH and KOH are used as alkali stimulants, the density of the cured product is low and the incidence of the internal void of the cured product is high. When Ca(OH)2 is used as an alkali stimulant, it shows the best performance when measuring pH, setting time, and strength. This seems to be due to the ionization degree of the (OH) group. However, the incidence of voids was the lowest.

scholarly journals Fly Ash/Blast Furnace Slag-Based Geopolymer as a Potential Binder for Mine Backfilling: Effect of Binder Type and Activator Concentration

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Jingping Qiu ◽  
Yingliang Zhao ◽  
Jun Xing ◽  
Xiaogang Sun
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Reaction Products ◽  
Lower Reactivity ◽  
The Matrix ◽  
Binder Type ◽  
Source Materials ◽  
Furnace Slag

This article investigated the potential of fly ash (FA)/blast furnace slag- (BFS-) based geopolymer as a novel backfilling material. The effects of NaOH concentration and FA/BFS mass ratio were explored through XRD, FTIR, and TG-DTG analyses. The results indicated that the reaction products and strengths of geopolymer depended on the NaOH concentration and types of source materials. Slump, final setting time, and setting ratio increased as a function of FA content. However, the increase in FA content reduced the compressive strength and microstructure of the backfilling material (BM) due to the lower reactivity than BFS. Microstructure analysis reveals that the matrix tends to be denser with the BFS content and NaOH concentration increase.

ON THE USE OF SLAG CEMENT COMPOSITIONS IN THE CONSTRUCTION OF WELLS

2017 ◽  
pp. 80-85
Author(s):  
V. P. Ovchinnikov ◽  
O. V. Rozhkova ◽  
N. A. Aksenova ◽  
P. V. Ovchinnikov
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Elevated Temperatures ◽  
Cement Mortar ◽  
Setting Time ◽  
Rheological Parameters ◽  
Slag Cement ◽  
Furnace Slag

In the article studies of oil-filled compositions with the addition of blast-furnace slag for strength at elevated temperatures are presented. The rheological parameters of the slag cement slag cement mortar, as well as the setting time, were studied. Conclusions are drawn about the prospects of further study of slag cementcontaining compositions.

scholarly journals Effect of Flue Gas Desulfurization Gypsum on the Properties of Calcium Sulfoaluminate Cement Blended with Ground Granulated Blast Furnace Slag

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 382 ◽  
Author(s):  
Danying Gao ◽  
Zhenqing Zhang ◽  
Yang Meng ◽  
Jiyu Tang ◽  
Lin Yang
Keyword(s):  
Blast Furnace ◽  
Mechanical Strength ◽  
Flue Gas ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Flue Gas Desulfurization ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This work aims to investigate the effect of additional flue gas desulfurization gypsum (FGDG) on the properties of calcium sulfoaluminate cement (CSAC) blended with ground granulated blast furnace slag (GGBFS). The hydration rate, setting time, mechanical strength, pore structure and hydration products of the CSAC-GGBFS mixture containing FGDG were investigated systematically. The results show that the addition of FGDG promotes the hydration of the CSAC-GGBFS mixture and improves its mechanical strength; however, the FGDG content should not exceed 6%.

scholarly journals Application areas of phosphogypsum in production of mineral binders and composites based on them: a review of research results

2018 ◽  
Vol 149 ◽  
pp. 01012 ◽  
Author(s):  
Leonid Dvorkin ◽  
Nataliya Lushnikova ◽  
Mohammed Sonebi
Keyword(s):  
Mechanical Properties ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Industrial Wastes ◽  
Cement Clinker ◽  
Complete Replacement ◽  
Slaked Lime ◽  
The Impact ◽  
Furnace Slag

The increase of the consumption of gypsum products in construction industry with a limited amount of natural gypsum deposits requires alternative sources of gypsum-containing raw materials. In some countries which have fertilizers industry plants, the problem can be solved using industrial wastes, e.g. phosphorgypsum – a byproduct of fertilizers’ production. Kept in dumps over decades, phosphorgypsum is subjected to the chemical changes due to washing out impurities with rain and other natural factors. However, there are observed deviations of harmful impurities in dumped PG depending on its age., Phosphorgypsum of any age requires chemical treatment to neutralize remains of phosphorus and sulfuric acids, fluorine compounds. According to our researches one of the most simple and effective method of neutralization the impurities is using lime-containing admixtures. The paper presents results of laboratory tests of phosphorgypsum as a component of clinker and non-clinker binders. There were investigated the impact of phosphorgypsum as admixture for clinker binders to substitute natural gypsum. Neutralized phosphorgypsum can be applied as mineralizing admixture in calcination of Portland cement clinker. Adding 2 to 2.5% of phosphorgypsum as setting time regulator resulted in a similar physical and mechanical properties compared to mix made with natural gypsum. Another important area of phosphorgypsum application is sulphate activatoion of low-clinker blast-furnace slag cement (clinker content is less than 19%). According to results, the incorporation of phosphorgypsum as sulphate activator in cement has the better effect as natural gypsum. Other development has been carried out to modify the phosphorgypsum binder properties. Complex additive consisted of polycarboxylate-based superplasticizer and slaked lime permitted an increase mechanical properties of hardened phosphorgypsum binder due to significant a reduction of water consumption. Such modified binder can be used as partial or complete replacement of gypsum binder for filling cements and finishing plasters. It can substitute gypsum in non-clinker binders like supersulphated cements. There were also developed compositions of supersulphated cements based on low-alumina blast furnace slag and phosphorgypsum. Supersulphated cements were tested in normal-weight and light-weight concrete.

scholarly journals Aplikasi Response Surface Methodology pada Optimasi Penambahan Blast Furnace Slag Terhadap Waktu Pengikatan dan Kuat Tekan Semen

2020 ◽  
Vol 4 (1) ◽  
pp. 61
Author(s):  
Hardjono Hardjono ◽  
Cucuk Evi Lusiani ◽  
Agung Ari Wibowo ◽  
Mochammad Agung Indra Iswara
Keyword(s):  
Compressive Strength ◽  
Response Surface Methodology ◽  
Blast Furnace ◽  
Response Surface ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Central Composite ◽  
Furnace Slag

Produksi semen setengah jadi (clinker) membutuhkan energi yang tinggi sehingga menggunakan batu bara dalam jumlah besar. Hal ini menyebabkan biaya produksi dari pabrik semen juga tinggi. Kebutuhan energi yang besar untuk menghasilkan clinker tersebut dapat dikurangi dengan menambahan blast furnace slag sebagai campuran pembuatan semen. Campuran clinker dapat menghasilkan produk semen yang memiliki waktu pengikatan dan kuat tekan sesuai SNI. Pengaruh penambahan blast furnace slag sebagai campuran clinker terhadap waktu pengikatan dan kuat tekan semen dapat dioptimalkan dengan response surface methodology (RSM) menggunakan Central Composite Design (CCD). Optimasi dengan menggunakan RSM bertujuan untuk mengetahui kondisi optimum pada penambahan blast furnace slag dan clinker terhadap variabel respon berupa waktu pengikatan awal, waktu pengikatan akhir, dan kuat tekan. Hasil uji ANOVA dan analisis response surface menunjukkan bahwa penambahan blast furnace slag sebagai campuran dalam pembuatan semen memberikan pengaruh yang signifikan terhadap waktu pengikatan awal, waktu pengikatan akhir, dan kuat tekan. Penambahan 5% blast furnace slag dengan 92,5% clinker pada campuran clinker dan gypsum merupakan kondisi optimum yang memberikan pengaruh signifikan terhadap variabel respon.The production of clinker consumes high energy and causes high production cost of cement industry. It can be reduced by adding blast furnace slag as a mixture in cement production. The blast furnace slag - clinker mixture can produce cement with setting time and compressive strength according to SNI. The effect of the addition of blast furnace slag as a clinker mixture to the setting time and compressive strength of cement can be optimized by response surface methodology (RSM) using Central Composite Design (CCD). Optimization by using RSM aims to determine the optimum condition of the blast furnace slag – clinker mixture to the initial setting time, final setting time, and compressive strength. ANOVA test results and response surface analysis show that the addition of blast furnace slag into the cement mixture has a significant influence on the initial setting time, final setting time, and compressive strength. The addition of  5% blast furnace slag with  92.5% clinker in the mixture of clinker and gypsum is the optimum condition which gives a significant effect on the response variable.

scholarly journals Optimization of an Eco-Friendly Hydraulic Road Binders Comprising Clayey Dam Sediments and Ground Granulated Blast-Furnace Slag

Buildings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 443
Author(s):  
Selma Bellara ◽  
Mustapha Hidjeb ◽  
Walid Maherzi ◽  
Salim Mezazigh ◽  
Ahmed Senouci
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Road Construction ◽  
Cement Clinker ◽  
Partial Replacement ◽  
Industry Waste ◽  
Impact Reduction ◽  
Compressive And Flexural Strengths ◽  
Furnace Slag

This study investigated the potential use of Zerdezas dam Calcined Sediments (CS) and El-Hadjar Blast Furnace Slag (GGBS) from northern Algeria as a partial replacement of cement (C) in normal hardening hydraulic road binders. Two binder mix designs were optimized using a Response Surface Methodology (RSM). The first mix, 50C35GGBS15CS, consisted of 50% cement, 35% blast furnace slag, and 15% calcined sediment. The second mix, 80C10GGBS10CS, consisted of 80% cement, 10% blast furnace slag, and 10% calcined sediments. The tests of workability, setting time, volume expansion, compressive and flexural strengths, porosity, and SEM were conducted to ensure that both mixes meet the standard requirements for road construction binders. The two proposed mixes were qualified as normal hardening hydraulic road binder. The reuse of the sediments will contribute to a better disposal of dam sediments and steel industry waste and to preserve natural resources that are used for manufacturing cement. It will also contribute to the environmental impact reduction of cement clinker production by reducing greenhouse gas emissions.

scholarly journals Protective Geopolymer Coatings Containing Multi-Componential Precursors: Preparation and Basic Properties Characterization

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Adhesive Strength ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Rapid Test ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.

scholarly journals Advances in the Analysis of Properties Behaviour of Cement-Based Grouts with High Substitution of Cement with Blast Furnace Slags

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 561
Author(s):  
Francisca Perez-Garcia ◽  
Maria Dolores Rubio-Cintas ◽  
Maria Eugenia Parron-Rubio ◽  
Jose Manuel Garcia-Manrique
Keyword(s):  
Mechanical Properties ◽  
Blast Furnace ◽  
Steel Industry ◽  
Blast Furnace Slag ◽  
Mechanical Response ◽  
Cement Replacement ◽  
Fresh State ◽  
Different Types ◽  
Furnace Slag ◽  
Slag Waste

This article presents a study of the main properties (consistency, workability, leaching, unsoundness, and mechanical properties) of cement grouts prepared with cement replacement by blast furnace slag (GGBS). Mixtures have been analyzed in the absence of additives and reached high replacement percentages. As shown in the different tests presented, the observed evolution of the resistance and workability of the mixtures makes them very interesting for its application. Different types of cement (CEM-I 42.5 and CEM-I 52.5 R) and different water/binder values (1 and 0.67) are used. The results present opportunities for the steel industry by the intensive valorization of slag waste. The reduction of the use of cement in construction is also one of the key aims of this line of research. Results show improvements in the mechanical response with good fresh state properties for substitution percentages up to 70%. It is verified with leaching analysis that these products have less impact on the environment.

Influence of Additve on Over-Sulfur Phosphogypsum-Ground Granulate Blast-Furnace Slag Cement

2015 ◽  
Vol 744-746 ◽  
pp. 1431-1434
Author(s):  
Zhi Jiang Lv ◽  
Zong Shou Lin ◽  
Ya Han ◽  
Hao Jie Wang
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Slag Cement ◽  
Hydration Mechanism ◽  
Polycarboxylate Superplasticizer ◽  
Granulate Blast Furnace Slag ◽  
Negative Effect ◽  
Mechanical Performances ◽  
Furnace Slag

The effect of sodium hydroxide (NaOH) and polycarboxylate superplasticizer amount on over-sulfur phosphogypsum–ground granulate blast-furnace slag cement was investigated. The mechanical performances and hydration mechanism of the cement with different proportions of NaOH and polycarboxylate superplasticizer (BASF) were analyzed based on setting time, the additive quantity of water, strength test, XRD and SEM analyses. The results showed that the polycarboxylate superplasticizer, can increase the densification and the strength of the cement ,to improve the performance of the cement anti-carbonation properties. NaOH as an alkali activator significantly reduces the cement setting time and improves the cement early strength. But the acceleration of hydration process produces coarse crystalline hydration products and the osteoporosis structure of hardened paste, which has a negative effect on long term strength.

Sign in / Sign up

Export Citation Format

Share Document