scholarly journals Effect of Iron Powder on Strength of Binary Blended Concrete

2019 ◽  
Vol 8 (3) ◽  
pp. 2490-2492
Keyword(s):  
Compressive Strength ◽  
Iron Powder ◽  
Strength Properties ◽  
Partial Replacement ◽  
Conventional Concrete ◽  
Iron Powders ◽  
Compressive Strength Test ◽  
Maximum Improvement ◽  
By Products ◽  
Binary Blended Concrete

The by-products generated from milling industries are iron powders which are harmful resources to human health since they are in the air and can be straightforwardly breathe in. To prevail over this setback we have to dispose the iron powder safely without any environmental hazards. As a result, consumption on iron powder in the concrete has been developed. This study made an attempt to make utilize iron powder waste as a part substitution of Portland cement in M25 grade concrete mix by the volume of fraction in the range of 0%, 1%, 2%, 3% and 4%. The compressive strength test was conducted for the various mix proportions and the achieved strength properties were compared with those of conventional concrete after 28 days. However, the effect of iron powder with 2% partial replacement of cement exhibit an maximum improvement in compressive strength of about 29.80% when compared to that of conventional concrete.

Assessment of Rice Husk Ash (RHA) and Calcium Chloride (CaCl2) on Compressive Strength of Concrete Grade 20

2018 ◽  
Vol 40 ◽  
pp. 22-29
Author(s):  
Joseph A. Ige ◽  
Mukaila A. Anifowose ◽  
Samson O. Odeyemi ◽  
Suleiman A. Adebara ◽  
Mufutau O. Oyeleke
Keyword(s):  
Compressive Strength ◽  
Calcium Chloride ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Conventional Concrete ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Strength Result

This research assessed the effect of Nigerian rice husk ash (RHA) and calcium chloride (CaCl2) as partial replacement of cement in concrete grade 20. Rice husk ash (RHA) is obtained by combustion of rice husk in a controlled temperature. The replacement of OPC with rice husk ash (RHA) were 0%, 5%, 10%, 15% and 20%. 1% of Calcium Chloride was blended with OPC/RHA in all the test specimens except from control mix. Concrete cubes of sizes 150mm x 150mm x 150mm were cast and cured in water for 7, 14 and 28 days respectively. Slump test was conducted on fresh concrete while density test and compressive strength test were conducted on hardened concrete. The slump results revealed that the concrete becomes less workable (stiff) as percentage increases. The compressive strength result at 28 days revealed that 5%RHA/1%CaCl2 have the highest strength of 26.82N/mm2 while 20%RHA/1%CaCl2 have the lowest strength (21.48N/mm2). Integration of 5%RHA/1%CaCl2 and 10%RHA/1%CaCl2 as cement replacement will produce a concrete of higher compressive strength compared to conventional concrete in grade 20 concrete.

scholarly journals Effect of Waste Tyre-Rubber Aggregate on the Strength Properties of Concrete

2018 ◽  
pp. 1-9
Author(s):  
Adetoye T. Oyebisi ◽  
Cordelia O. Osasona
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Strength Properties ◽  
Partial Replacement ◽  
Concrete Construction ◽  
Conventional Concrete ◽  
Waste Tyre ◽  
Rubber Aggregates

This research studied strength-characteristics of concrete using waste tyre-rubber as partial replacement for coarse aggregate in concrete construction and compares the results to those of conventional concrete. The specimens were produced with percentage replacements of the coarse aggregate by 5%, 10% and 15 % of rubber aggregate. A control mix with no replacement of the coarse aggregate was produced, to make a comparative analysis. The samples consisted of concrete cubes, cylinders and beams. Various tests (such as slump, compressive strength, splitting tensile strength and flexural strength tests), were conducted. Data-collection was mainly based on the results of the tests conducted on the specimens in the laboratory. The results show that there is a reduction in the compressive strength of the concrete, due to the inclusion of rubber aggregates. Compressive strength losses of 12.69%, 17.75% and 25.33% were noticed for 5%, 10%, 15% replacement of coarse aggregate, respectively; tensile strength losses of 13.01%, 20.12%, and 24.76% were observed, respectively, when 5%, 10%, 15% of the coarse aggregate was replaced, after 28 days of curing; -0.1%, -0.15% and 0.2% decrease in flexural strength was observed for 5%, 10% and 15% replacement, respectively, after curing for 28 days. Rubberised concrete was found to have some desirable characteristics (such as lower density, enhanced ductility, and a slight increase in flexural strength in the lower compressive strength concrete categories). The overall results show that it is possible to use recycled rubber tyres in concrete construction, as a partial replacement for coarse aggregates. Nevertheless, the percentage of replacement should be limited to 10% (which ensures the strength of the concrete is kept within the required range), and the application should be restricted to particular cases where the properties related to the replacement with the rubber aggregates clearly indicate an improvement on conventional concrete, and so are desirable.

scholarly journals A Review on Compressive Strength of Concrete Containing Waste Cathode Ray Tube Glass as Aggregates

2021 ◽  
Vol 1 (1) ◽  
pp. 1-14
Author(s):  
Nurul Noraziemah Mohd Pauzi
Keyword(s):  
Compressive Strength ◽  
Construction Material ◽  
Concrete Strength ◽  
Strength Properties ◽  
Partial Replacement ◽  
Natural Sand ◽  
Conventional Concrete ◽  
Fine Aggregates ◽  
Cathode Ray Tube ◽  
Recycling Techniques

The issue of the cathode ray tube (CRT) technology facing its end-of-time and increasing quantities across the globe has acquired the responsiveness of many researchers. The use of waste CRT glass as a construction material has fascinated them due to its significant advantage in recycling the hazardous and non-biodegradable waste CRT glass. However, lack of knowledge about the effects and features of CRT glass as a construction material could be a hindrance to the excessive utilization of waste CRT glass. Therefore, in order to establish the idea of using CRT waste glass as a more common construction material, this paper reviews several recycling techniques of CRT glass and further detail on the workability, density, and compressive strength properties of concrete and mortar using CRT glass (treated or untreated) as fine aggregates. The review showed that, generally, the use of CRT glass as a complete or partial replacement of natural sand shows a slight increase in density, workability, and concrete strength compared to conventional concrete. However, there are no clear trends that can be concluded as this review also showed that various factors influenced its performance, such as percentage replacement, particle size, lead (Pb) content, and types of admixtures.

scholarly journals Pengaruh Penambahan Sat Additive Addition H.E Terhadap Kuat Tekan Beton

2020 ◽  
Vol 2 (1) ◽  
pp. 31-57
Author(s):  
Ni Ketut Sri Astati Sukawati
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Partial Replacement ◽  
Work Related ◽  
Coarse Aggregates ◽  
Alternative Ingredients ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Artificial Stone

Concrete with various variants is a basic requirement in building a building. The concrete mixture is diverse depending on the planning made beforehand. The cement mixture is usually in the form of a mixture of artificial stone, cement, water and fine aggregates and coarse aggregates. Aggregates (fine aggregates and coarse aggregates) function as fillers in concrete mixtures. (Subakti, A., 1994). However, in building construction, additives are often added, but there is still a sense of uncertainty at the time of dismantling the mold and the reference before the concrete reaches sufficient strength to carry its own weight and the carrying loads acting on it. To overcome the time of carrying out work related to concrete, it is necessary to find an alternative solution, for example by looking for alternative ingredients of concrete mixture on the basis of consideration without reducing the quality of the concrete. From the results of previous studies it was stated that due to the partial replacement of cement with Fly Ash, the strength of the pressure and tensile strength of the concrete had increased (Budhi Saputro, A., 2008). Based on the description above, the author seeks to examine how the compressive strength of concrete characteristics that occur by adding additives Addition H.E in the concrete mixture and is there any additive Additon H.E effect on the increase in the compressive strength characteristic of the concrete. From the results of the study, it was found that the compressive strength of the concrete with the addition of additives HE was that after the compressive strength test of the concrete cube was carried out and the analysis of concrete compressive strength of 10 specimens, in each experiment a cube specimen was made with the addition of additons. HE with a dose of 80 cc, 120 cc, and 200 cc can accelerate and increase the compressive strength of concrete characteristics.

scholarly journals Comparison of Conventional Concrete and Replacement of River Sand by Waste Foundry Sand and Cement by Nano-Silica

2020 ◽  
pp. 201-205
Keyword(s):  
Experimental Investigation ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Nano Silica ◽  
River Sand ◽  
Conventional Concrete ◽  
Foundry Sand ◽  
Concrete Production ◽  
Waste Foundry Sand

This paper presents an experimental investigation on the properties of concrete in which like cement is partially replacing by used nano silica and is partially replacing by used waste foundry sand. Because now a day the world wide consumption of sand as cement and as fine aggregate in concrete production is very high. Nano silica and waste foundry sand are major by product of casting industry and create land pollution. The cement will be replaced with nano silica and the river sand will be replaced with waste foundry sand (0%, 5%, 10%, 15%, 20%). This experimental investigation was done and found out that with the increase in the nano silica and waste foundry sand ratio. Compression test has been done to find out the compressive strength of concrete at the age of 7, 14, 21, and 28. Test result indicates in increasing compressive strength of plain concrete by inclusion of nano silica as a partial replacement of cement and waste foundry sand as a partial replacement of fine aggregate.

scholarly journals THE EFFECT OF CERAMIC WASTE AS COARSE AGGREGATE ON STRENGTH PROPERTIES OF CONCRETE

2017 ◽  
Vol 36 (3) ◽  
pp. 691-696
Author(s):  
EE Ikponmwosa ◽  
SO Ehikhuenmen
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Control Sample ◽  
Strength Properties ◽  
Waste Material ◽  
Partial Replacement ◽  
Replacement Level ◽  
Ceramic Waste ◽  
Curing Age

This paper reports the findings on an experimental investigation of the effect of partial replacement of coarse aggregate with ceramic waste on strength properties of concrete. Compressive strength tests were conducted using 150x150x150mm cube specimens, while tensile strength was investigated using 150x300mm cylinder specimens. Results of tests show that workability, density, compressive and flexural strength of concrete decreased with increase in ceramic waste content. The compressive strength at 90 days curing age for the control sample was 24.67 N/mm2. Compressive strength values at 90 days curing age for  25%, 50% and 75% replacement levels were 21.78 N/mm2, 19.85 N/mm2and 17.85 N/mm2 respectively. The decrease in density and strength was due to ceramic waste being lighter and more porous than normal coarse aggregate. Tensile strength of concrete with ceramic waste decline gradually from 8.39 N/mm2 to 6.13 N/mm2 for the control and 75% replacement samples respectively. This could be attributed to the water absorption capacity and external porcelain nature of the waste material. A production cost savings of 10.7% for 1:2:4 concrete mix was noted at 75% replacement level. This study concludes that ceramic waste could be used for both structural and non-structural works and recommends that beyond 75% replacement level, ceramic waste material should not be used in concrete structures where strength is the major consideration. http://dx.doi.org/10.4314/njt.v36i3.5

BEHAVIOR OF M 50 GRADE SELF-COMPACTING CONCRETE DEVELOPED USING PORTLAND SLAG CEMENT AND METAKAOLIN

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Sravya Nalla ◽  
Janardhana Maganti ◽  
Dinakar Pasla
Keyword(s):  
Compressive Strength ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Test Results ◽  
Slag Cement ◽  
Self Compacting Concrete ◽  
Destructive Testing ◽  
Compressive Strength Test ◽  
Portland Slag Cement ◽  
Strength And Durability

Self-compacting concrete (SCC) is a revolutionary development in concrete construction. The addition of mineral admixtures like metakaolin, which is a highly reactive pozzolana to the SCC mixes, gives it superior strength and durability. The present work is an effort to study the behavior of M50 grade SCC by partial replacement of Portland Slag Cement (PSC) with metakaolin. Its strength and durability aspects are comparable with a controlled concrete (without replacement of cement). In the present work, a new mix design methodology based on the efficiency of metakaolin is adopted. The optimum percentage replacement of cement with metakaolin is obtained based on compressive strength test results. The influence of metakaolin on the workability, compressive strength, splitting tensile strength and flexural strength of SCC and its behavior when subjected to elevated temperature was investigated through evaluation against controlled concrete and non-destructive testing. From the test results, it was observed that incorporation of metakaolin at an optimum dosage satisfied all the fresh properties of SCC and improved both the strength and durability performance of SCC compared to controlled concrete.

Influence of Fly Ash and Basalt Fibers on Strength and Chloride Penetration Resistance of Self-Consolidating Concrete

2016 ◽  
Vol 866 ◽  
pp. 3-8 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Waddah Al Hawat
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Strength Properties ◽  
Chloride Penetration ◽  
Partial Replacement ◽  
Basalt Fibers ◽  
Self Consolidating Concrete ◽  
Chloride Penetration Resistance ◽  
Hardened Properties

Fly ash is a sustainable partial replacement of Portland cement that offers significant advantages in terms of fresh and hardened properties of concrete. This paper presents the findings of a study that aims at assessing the durability and strength properties of sustainable self-consolidating concrete (SCC) mixes in which Portland cement was partially replaced with 10%, 20%, 30%, and 40% fly ash. The study confirms that replacing Portland cement with fly ash at all of the percentages studied improves resistance of concrete to chloride penetration. The 40% fly ash mix exhibited the highest resistance to chloride penetration compared to the control mix. Despite the relative drop in compressive strength after 7 days of curing, the 28-day compressive strength of 40% SCC mix reached 55.75 MP, which is very close to the control mix. The study also confirms that adding 1%, 1.5%, and 2% basalt fibers, respectively, to the 40% fly ash mix improves the resistance to chloride penetration compared to the mix without basalt fibers.

scholarly journals Comparison of Compressive Strength of Concrete by Partial Replacement of Cement with GGBS and Silica Fume with Sea Water Curing and Addition with Fibers

2021 ◽  
pp. 31-39
Author(s):  
A Aswani and Janardhan G
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
Sea Water ◽  
Glass Fibers ◽  
Vital Role ◽  
Strength Test ◽  
Partial Replacement ◽  
Compressive Strength Test ◽  
Water Curing ◽  
Compressive Strength Of Concrete

In construction world concrete plays a vital role, around 60% of structure consists of Concrete. However, the production of Portland cement, an essential constituent of concrete, leads to the release of significant amounts of CO2, depletion of natural resources and environmental degradation. This paper investigates the compressive strength of concrete by replacing cement with GGBS and silica fume effect of glass fibers on performance of concrete is studied. In this present work a humble attempt had been made to evaluate and compare the compressive strengths of GGBS blended concrete cubes with controlled concrete cubes cured under sea water for 28 days. By conducting the tests on the cubes, conclusions were drawn after plotting and analyzing the results. Compressive strength test is conducted on the samples after 28 days. The optimum value is obtained at 15% replacement with GGBS and 5% with Silica fume. In this study again we trailed addition with Glass fibers with the percentage of 0.5%,1.0%,1.5%, compressive strength have been studied. Finally at 1.0% addition we get maximum strength compared to controlled mix.

scholarly journals Study of Light Weight Fibre Reinforced Concrete by Partial Replacement of Coarse Aggregate with Pumice Stone

2021 ◽  
Vol 9 (9) ◽  
pp. 933-940
Author(s):  
Mohammed Sohel Ahmed
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Light Weight ◽  
Structural Members ◽  
Conventional Concrete ◽  
Shrinkage Cracking ◽  
Pumice Stone ◽  
Average Compressive Strength

Abstract: As the demand for the structural members application in the concrete industry is continuously increasing simultaneously many a times it is required to lower the density of concrete enabling light weight which helps in easy handling of the concrete and its members. In this research an experimental endeavour has been made to equate conventional concrete with light weight by partially substituting the coarse aggregate with the pumice stone aggregate in M30 grade mix design. Simultaneously small fibres of Recron3's Polypropylene have been applied to the concrete as a reinforcing medium to minimize shrinkage cracking and improve tensile properties. The coarse aggregate was substituted by the pumice aggregate in 10, 20, 30, 40, and 50 percent and fibres respectively in 0.5, 1, 1.5, 2 and 2.5 percent. The experiment is focused on strength parameters to determine the most favourable optimum percent with respect to conventional concrete. Keywords: OPC (Ordinary Portland Cement)1, FA (Fine Aggregate)2, CA (Coarse Aggregate) 3, fck (Characteristic Compressive Strength at 28days)4, Sp. Gr (Specific Gravity)5, WC (Water Content)6, W/C (Water Cement Ratio)7, S (Standard Deviation)8, Fck (Target Average Compressive Strength at 28days)9.

Sign in / Sign up

Export Citation Format

Share Document