Diesel engine performance at the intake of the hydrogen&air mixture

2021 ◽  
pp. 119-126
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Engine Performance ◽  
Calorific Value ◽  
Hydrocarbon Emissions ◽  
The Difference

The prospects of using hydrogen as a motor fuel are noted. The problems that arise when converting a diesel engine to run on hydrogen are considered. The features of the organization of the working process of enginesrunning on hydrogen are analyzed. A method of supplying a hydrogenair mixture to a diesel engine is investigated. To supply hydrogen to the engine cylinders, it is proposed to use the Leader4M installation developed by TechnoHill Club LLC (Moscow). Experimental studies of a stationary diesel engine of the D245.12 S type with the supply of hydrogen at the inlet obtained at this installation are carried out. At the maximum power mode, the supply of hydrogen from this installation to the inlet of the diesel engine under study was 0.9 % by weight (taking into account the difference in the calorific value of oil diesel fuel and hydrogen). Such a supply of hydrogen in the specified mode made it possible to increase the fuel efficiency of the diesel engine and reduce the smoke content of exhaust gases, carbon monoxide and unburned hydrocarbon emissions. Keywords internal combustion engines; diesel engine; diesel fuel; hydrogen; hydrogenair mixture; fuel efficiency; exhaust gas toxicity indicators

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Combustion Engines ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.

USE OF NORTHERN ECOTYPE SOYBEANS FOR BIOFUEL PRODUCTION

2020 ◽  
pp. 22-30
Author(s):  
SERGEY N. DEVYANIN ◽  
◽  
VLADIMIR A. MARKOV ◽  
ALEKSANDR G. LEVSHIN ◽  
TAMARA P. KOBOZEVA ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Soybean Oil ◽  
Diesel Fuel ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Biodiesel Production ◽  
Biofuel Production ◽  
Exhaust Gases ◽  
Oil Productivity ◽  
Toxic Components

The paper presents the results of long-term research on the oil productivity and chemical composition of soybean oil of the Northern ecotype varieties in the Central Non-Black Earth Region. The authors consider its possible use for biodiesel production. Experiments on growing soybeans were carried out on the experimental fi eld of Russian State Agrarian University –Moscow Timiryazev Agricultural Academy (2008-2019) on recognized ultra-early ripening varieties of the Northern ecotype Mageva, Svetlaya, Okskaya (ripeness group 000). Tests were set and the research results were analyzed using standard approved methods. It has been shown that in conditions of high latitudes (57°N), limited thermal resources of the Non-Chernozem zone of Russia (the sum of active temperatures of the growing season not exceeding 2000°С), the yield and productivity of soybeans depend on the variety and moisture supply. Over the years, the average yield of soybeans amounted to 1.94 … 2.62 t/ha, oil productivity – 388 … 544 kg/ha, oil content – 19…20%, the content of oleic and linoleic fatty acids in oil – 60%, and their output from seeds harvested – 300 kg/ha. It has been established that as soybean oil and diesel fuel have similar properties,they can be mixed by conventional methods in any proportions and form stable blends that can be stored for a long time. Experimental studies on the use of soybean oil for biodiesel production were carried out on a D-245 diesel engine (4 ChN11/12.5). The concentrations of toxic components (CO, CHx, and NOx) in the diesel exhaust gases were determined using the SAE-7532 gas analyzer. The smoke content of the exhaust gases was measured with an MK-3 Hartridge opacimeter. It has been experimentally established that the transfer of a diesel engine from diesel fuel to a blend of 80% diesel fuel and 20% lubrication oil leads to a change in the integral emissions per test cycle: nitrogen oxides in 0.81 times, carbon monoxide in 0.89 times and unburned hydrocarbons in 0.91 times, i.e. when biodiesel as used as a motor fuel in a serial diesel engine, emissions of all gaseous toxic components are reduced. The study has confi rmed the expediency of using soybeans of the Northern ecotype for biofuel production.

Experimental Studies on the Performance of C.I Engine with Fish Oil Methyl Ester as Fuel for Various Blends of Diesel and LPG

2015 ◽  
Vol 787 ◽  
pp. 687-691
Author(s):  
Tarigonda Hari Prasad ◽  
R. Meenakshi Reddy ◽  
P. Mallikarjuna Rao
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Research Work ◽  
Experimental Studies ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Inlet Manifold

Fossil fuels are exhausting quickly because of incremental utilization rate due to increase population and essential comforts on par with civilization. In this connection, the conventional fuels especially petrol and diesel for internal combustion engines, are getting exhausted at an alarming rate. In order to plan for survival of technology in future it is necessary to plan for alternate fuels. Further, these fossil fuels cause serious environmental problems as they release toxic gases into the atmosphere at high temperatures and concentrations. The predicted global energy consumption is increasing at faster rate. In view of this and many other related issues, these fuels will have to be replaced completely or partially by less harmful alternative, eco-friendly and renewable source fuels for the internal combustion engines. Hence, throughout the world, lot of research work is in progress pertaining to suitability and feasibility of alternative fuels. Biodiesel is one of the promising sources of energy to mitigate both the serious problems of the society viz., depletion of fossil fuels and environmental pollution. In the present work, experiments are carried out on a Single cylinder diesel engine which is commonly used in agricultural sector. Experiments are conducted by fuelling the diesel engine with bio-diesel with LPG through inlet manifold. The engine is properly modified to operate under dual fuel operation using LPG through inlet manifold as fuel along FME as ignition source. The brake thermal efficiency of FME with LPG (2LPM) blend is increased at an average of 5% when compared to the pure diesel fuel. HC emissions of FME with LPG (2LPM) blend are reduced by about at an average of 21% when compared to the pure diesel fuel. CO emissions of FME with LPG (2LPM) blends are reduced at an average of 33.6% when compared to the pure diesel fuel. NOx emissions of FME with LPG (2LPM) blend are reduced at an average of 4.4% when compared to the pure diesel fuel. Smoke opacity of FME with LPG (2LPM) blend is reduced at an average of 10% when compared to the pure diesel fuel.

scholarly journals A Review on Techniques to Improve Performance and Reduce Emissions of Diesel Engine Running With Higher Viscous Fuels (HVFs)

2019 ◽  
Author(s):  
Saiful Bari ◽  
Shekh Nisar Hossain ◽  
Idris Saad
Keyword(s):  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
Calorific Value ◽  
Combustion Efficiency ◽  
Fuel Price ◽  
Fuel Blend ◽  
Environmental Friendliness ◽  
Biodiesel Fuels ◽  
Ci Engines

Abstract Due to skyrocketing fuel price and demand, engine manufacturers and researchers have been thriving to find alternative sources of fuel for internal combustion engines. Biodiesel and vegetable-based fuels are prospective substitutes for petro-diesel fuel for compressions ignition (CI) or diesel engines, and favourable over petro-diesel fuel in terms of sustainability and environmental friendliness. It is found from the literatures that higher viscous fuels (HVFs) and biodiesel fuels have substandard engine performance and emissions especially in the case of brake specific fuel consumption (BSFC), torque and NOx emissions compared to those of the engines using petro-diesel. This is mainly due to their higher viscosity and density as well as lower volatility and calorific value and thus, they are termed as higher viscous fuels. Furthermore, the higher viscosity and density of HVFs retard the combustion efficiency since HVFs are less prone to evaporate, diffuse and mix properly with the in-cylinder air. Based on these findings, researchers have put effort into improving the performance of CI engines running with HVFs. Generally, three techniques are very popular by the researchers, namely, blending the HVFs with petro-diesel (known as fuel blend), preheating the HVFs, and altering the injection strategy from the original engine-settings for petro-diesel operation. In this paper, a comprehensive review is presented on these techniques to improve the performance of CI engines run on HVFs.

scholarly journals Influence of Propanol as Additive with Diesel Jatropha Biodiesel Blend Fuel for Diesel Engine

2021 ◽  
Vol 8 (2) ◽  
pp. 986-1001
Author(s):  
Abu Saleh Ahmed ◽  
Nur Adibah Abdul Rahim ◽  
Md Rezaur Rahman ◽  
Mohammad Shahril Osman
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Calorific Value ◽  
Renewable Energy Resources ◽  
Ft Ir ◽  
Ir Analysis ◽  
Negative Impacts ◽  
Blend Fuel

Fossil fuels are widely recognized as non-renewable energy resources. They play an important role in our daily life because they can be used in various applications such as the production of soap and cosmetics, as an energy source and for transportation. However, the use of these fossil fuels causes negative impacts on humans, animals and the environment. These happen due to the emission of harmful gases into the atmosphere. Not only that, the available fossil fuels are decreasing due to continuous usage by humans. As a result, researchers investigated finding alternative ways to overcome this issue by replacing diesel fuel with biodiesel. Biodiesel is more environmentally friendly relative to diesel fuel. A research study was conducted involving biodiesel. The purpose of this study was to produce Jatropha Biodiesel, as well as evaluate the properties of Jatropha biodiesel and diesel Jatropha biodiesel blended with propanol. The production of Jatropha Biodiesel was done by using two-step transesterification which was an acid-catalyzed transesterification and base-catalyzed transesterification. Different methanol to oil ratios had been used to identify the best ratio to reduce the FFA content in the CJO. 9:1 was the best methanol to oil ratio and then tested with different catalyst weights. It was found that an increase in the weight of catalyst might reduce the amount of biodiesel yield. In addition, this study also investigated and predicted the engine performance and characteristics of diesel Jatropha biodiesel blended with propanol at different blending ratios. The properties of these test fuels were studied. Bomb calorimeter, Fourier Transform Infrared Spectroscopy (FT-IR) analysis and Diesel Engine test were done. Thus, the calorific value and functional group of the test fuels were identified and determined. The calorific value of biodiesel was much higher than conventional diesel due to the existence of oxygen. This could be proven as the analysis of FT-IR also showed a (C=O) bond which reflected the presence of oxygen. The oxygen helped in combustion besides reducing the hydrocarbon released into the air. These findings were then reflected and related to the performance of diesel engines.  

scholarly journals Experimental Studies of Diesel Engine Performance, Combustion and Emission Characteristics with Diesel and Pumpkin Seed Oil Blends

2019 ◽  
Vol 8 (12) ◽  
pp. 1294-1299
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Seed Oil ◽  
Experimental Studies ◽  
Engine Performance ◽  
Heat Emission ◽  
Biodiesel Fuel ◽  
Pumpkin Seed ◽  
Oil Blends ◽  
Pumpkin Seed Oil

In the current study, the primary components used are pumpkin seed oil biodiesel with diesel was tested in diesel engine and its performance, exhaust emissions, and its effects were observed. The pumpkin seed oil that is used to produce biodiesel undergoes transesterification process along with ethanol, sulphuricacid ,andNaOH catalysts . With blends like B0,B20,B40,B60,B80,and B100, the test on engine performance is obtained, and the reports exposed that, B40 is overlying blend among the other biodiesel blends. In addition, to enhance the performance characteristics of B20,B60,B80 by volume was combined with B40 blend. Due to lower heating characteristics of biodiesel, the observations of BTE for B40 is 4.6% lower than diesel. But the observations of BSFC for B40 is 7.3% higher than diesel. The heat emission rate ofB20,B40,andB60 are almost identical to diesel fuel ,apace with ,at higher loads B40 emitted37.5%less CO and NOx emission was raised at the rate of 95% when correlated to diesel fuel. However, It is observed that there is no major difference not much difference in the emissions (HC, NO, andCO) and characteristics of the engine when using the diesel fuel and Pumpkin seed biodiesel fuel blends

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Fuel Additives ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified. Key words: diesel fuel, diesel fuel additives, engine efficiency.

Increasing the efficiency of series D49 diesel engines by transfer to gas engine fuel

2019 ◽  
pp. 15-23
Author(s):  
Alexey Muratov ◽  
Andrey Balakin ◽  
Denis Bardin ◽  
Valentina Tselikovskaya ◽  
Leyla Kurmanova
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Diesel Fuel ◽  
Power Plants ◽  
Internal Combustion Engines ◽  
Motor Fuel ◽  
Engine Fuel ◽  
Diesel Locomotive ◽  
Complete Replacement ◽  
Gas Engine

Objective: Studying the effect of diesel locomotives on the use of natural gas as motor fuel. Identification of the main advantages of using natural gas in internal combustion engines. Analysis of the effect of gas engine fuel on the performance of diesel locomotive power plants. Methods: Simulation of the working process of two engines: the first – on diesel fuel, the second – on the gas mixture. Adjustment of the mathematical model according to the real parameters of 1А-5Д49-2 diesel engine, taken during the rheostat tests of 2ТЭ116 diesel locomotive. Conducting calculation and experimental studies to assess the effect of the complete replacement of diesel fuel with natural gas on the operation of the locomotive power plant; accumulation of computational and experimental data, their systematization and statistical analysis. Theoretical dependences of the change in the specific effective fuel consumption of a diesel engine operating on natural gas through the gas cycle on the position of the driver’s controller, as well as dependences of the change in the effective performance of a diesel engine have been discussed. The calculated values are compared for the diesel engine operating on natural gas and the diesel engine operating on diesel fuel. Results: The calculated dependencies of the performance of Series 1А-5Д49-2 (16ЧН26/26) diesel engine of 2ТЭ116 diesel locomotive with the use of gas engine fuel have been obtained. The obtained data has been analyzed allowing carrying out theoretical estimation of efficiency of natural gas used as gas engine fuel throughout the entire operating range of 1А-5Д49-2 (16ЧН26/26) diesel engine of 2ТЭ116 diesel locomotive. A conclusion was confirmed about the expediency and efficiency of using natural gas in railway transport, particularly diesel locomotives. The influence of replacement of diesel fuel with natural gas on the performance indicators of diesel locomotives has been determined. Practical importance: The obtained dependencies will help in forecasting and in the theoretical evaluation of the feasibility of using natural gas as a motor fuel for locomotive power plants.

Energetic properties of peat saturated with petroleum products

2020 ◽  
Vol 13 (2) ◽  
pp. 105-109
Author(s):  
E. S. Dremicheva
Keyword(s):  
Crude Oil ◽  
Diesel Fuel ◽  
Energy Use ◽  
Experimental Studies ◽  
Calorific Value ◽  
Petroleum Products ◽  
Ash Content ◽  
Motor Oil ◽  
Initial Sample

This paper presents a method of sorption using peat for elimination of emergency spills of crude oil and petroleum products and the possibility of energy use of oil-saturated peat. The results of assessment of the sorbent capacity of peat are presented, with waste motor oil and diesel fuel chosen as petroleum products. Natural peat has been found to possess sorption properties in relation to petroleum products. The sorbent capacity of peat can be observed from the first minutes of contact with motor oil and diesel fuel, and significantly depends on their viscosity. For the evaluation of thermal properties of peat saturated with petroleum products, experimental studies have been conducted on determination of moisture and ash content of as-fired fuel. It is shown that adsorbed oil increases the moisture and ash content of peat in comparison with the initial sample. Therefore, when intended for energy use, peat saturated with petroleum products is to be subjected to additional drying. Simulation of net calorific value has been performed based on the calorific values of peat and petroleum products with different ratios of petroleum product content in peat and for a saturated peat sample. The obtained results are compared with those of experiments conducted in a calorimetric bomb and recalculated for net calorific value. A satisfactory discrepancy is obtained, which amounts to about 12%. Options have been considered providing for combustion of saturated peat as fuel (burnt per se and combined with a solid fuel) and processing it to produce liquid, gaseous and solid fuels. Peat can be used to solve environmental problems of elimination of emergency spills of crude oil and petroleum products and as an additional resource in solving the problem of finding affordable energy.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Sign in / Sign up

Export Citation Format

Share Document