scholarly journals Influence of Propanol as Additive with Diesel Jatropha Biodiesel Blend Fuel for Diesel Engine

2021 ◽  
Vol 8 (2) ◽  
pp. 986-1001
Author(s):  
Abu Saleh Ahmed ◽  
Nur Adibah Abdul Rahim ◽  
Md Rezaur Rahman ◽  
Mohammad Shahril Osman
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Calorific Value ◽  
Renewable Energy Resources ◽  
Ft Ir ◽  
Ir Analysis ◽  
Negative Impacts ◽  
Blend Fuel

Fossil fuels are widely recognized as non-renewable energy resources. They play an important role in our daily life because they can be used in various applications such as the production of soap and cosmetics, as an energy source and for transportation. However, the use of these fossil fuels causes negative impacts on humans, animals and the environment. These happen due to the emission of harmful gases into the atmosphere. Not only that, the available fossil fuels are decreasing due to continuous usage by humans. As a result, researchers investigated finding alternative ways to overcome this issue by replacing diesel fuel with biodiesel. Biodiesel is more environmentally friendly relative to diesel fuel. A research study was conducted involving biodiesel. The purpose of this study was to produce Jatropha Biodiesel, as well as evaluate the properties of Jatropha biodiesel and diesel Jatropha biodiesel blended with propanol. The production of Jatropha Biodiesel was done by using two-step transesterification which was an acid-catalyzed transesterification and base-catalyzed transesterification. Different methanol to oil ratios had been used to identify the best ratio to reduce the FFA content in the CJO. 9:1 was the best methanol to oil ratio and then tested with different catalyst weights. It was found that an increase in the weight of catalyst might reduce the amount of biodiesel yield. In addition, this study also investigated and predicted the engine performance and characteristics of diesel Jatropha biodiesel blended with propanol at different blending ratios. The properties of these test fuels were studied. Bomb calorimeter, Fourier Transform Infrared Spectroscopy (FT-IR) analysis and Diesel Engine test were done. Thus, the calorific value and functional group of the test fuels were identified and determined. The calorific value of biodiesel was much higher than conventional diesel due to the existence of oxygen. This could be proven as the analysis of FT-IR also showed a (C=O) bond which reflected the presence of oxygen. The oxygen helped in combustion besides reducing the hydrocarbon released into the air. These findings were then reflected and related to the performance of diesel engines.  

Diesel engine performance at the intake of the hydrogen&air mixture

2021 ◽  
pp. 119-126
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Engine Performance ◽  
Calorific Value ◽  
Hydrocarbon Emissions ◽  
The Difference

The prospects of using hydrogen as a motor fuel are noted. The problems that arise when converting a diesel engine to run on hydrogen are considered. The features of the organization of the working process of enginesrunning on hydrogen are analyzed. A method of supplying a hydrogenair mixture to a diesel engine is investigated. To supply hydrogen to the engine cylinders, it is proposed to use the Leader4M installation developed by TechnoHill Club LLC (Moscow). Experimental studies of a stationary diesel engine of the D245.12 S type with the supply of hydrogen at the inlet obtained at this installation are carried out. At the maximum power mode, the supply of hydrogen from this installation to the inlet of the diesel engine under study was 0.9 % by weight (taking into account the difference in the calorific value of oil diesel fuel and hydrogen). Such a supply of hydrogen in the specified mode made it possible to increase the fuel efficiency of the diesel engine and reduce the smoke content of exhaust gases, carbon monoxide and unburned hydrocarbon emissions. Keywords internal combustion engines; diesel engine; diesel fuel; hydrogen; hydrogenair mixture; fuel efficiency; exhaust gas toxicity indicators

Tribological and emission characteristics of indirect ignition diesel engine fuelled with waste edible oil

2016 ◽  
Vol 68 (5) ◽  
pp. 554-560 ◽  
Author(s):  
De-Xing Peng
Keyword(s):  
Economic Growth ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Vital Role ◽  
Fuel Additive ◽  
Content Type ◽  
Lubricating Property

Purpose Energy is the prime mover of economic growth and is vital to the sustenance of a modern economy. Future economic growth depends heavily on the long-term availability of energy from sources that are affordable, accessible and environmentally friendly. Regulating the sulfur content in diesel fuel is expected to reduce the lubricity of these fuels, which may result in increased wear and damage of fuel injection systems in diesel engines. Design/methodology/approach The tribological properties of the biodiesels as additive in pure petro-diesel are studied by ball-on-ring wear tester to find optimal concentration, and the mechanism of the reduction of wear and friction will be investigated by optical microscopy. Findings Studies have shown that low concentrations of biodiesel blends are more effective as lubricants because of their superior polarity. Using biodiesel as a fuel additive in a pure petroleum diesel fuel improves engine performance and exhaust emissions. The high biodegradability and superior lubricating property of biodiesel when used in compression ignition engines renders it an excellent fuel. Originality/value This detailed experimental investigation confirms that biodiesel can substitute mineral diesel without any modification in the engine. The use of biofuels as diesel engine fuels can play a vital role in helping the developed and developing countries to reduce the environmental impact of fossil fuels.

scholarly journals Performance of Diesel Engine using Bio-Fuel From Sesame Oil

2019 ◽  
Vol 8 (10) ◽  
pp. 1554-1558 ◽  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Industrial Revolution ◽  
Engine Performance ◽  
High Standard ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
High Viscosity ◽  
Sesame Oil

Energy has become a crucial factor for humanity to continue the economic growth and maintain high standard of living especially after industrial revolution. “Fossil fuels are still the main source of energy. But the endless consumption of fossil fuels will bring the reserve to an end in near future. As a result fuel prices are soaring because of diminishing supply than demand. So researchers world over are in constant search of alternate fuels in the last three to four years, aimed at reducing CO2 emissions and global dependency on fossil fuels. The use of vegetable oils as a fuel in diesel engine causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is blending of fuel. In this study, a mix of 5%, 10%,15%, 20%, 25% sesame oil and diesel fuel was used as alternative fuel in a direct injection diesel engine. Diesel engine performance and exhaust emissions were investigated and compared with the diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil diesel fuel are close to the values obtained from diesel fuel and the amount of exhaust emissions are lower than those of diesel fuel. Hence it is seen that mix of sesame oil 20% and 80% diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly” fuel in terms of emission parameters.

scholarly journals Evaluation of Diesel Engine Performance and Exhaust Emission Characteristics Using Waste Cooking Oil

2015 ◽  
Vol 773-774 ◽  
pp. 425-429 ◽  
Author(s):  
Nur Atiqah Ramlan ◽  
Abdul Adam Abdullah ◽  
Mohd Herzwan Hamzah ◽  
Nur Fauziah Jaharudin ◽  
Rizalman Mamat
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Engine Speed ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Cooking Oil ◽  
Conventional Diesel Fuel

The depletion of fossil fuels as well as the rises of greenhouse gases had caused most government worldwide to follow the international energy policies for the use of biodiesel. One of the economical sources for biodiesel production is waste cooking oil. The use of waste cooking oil is more sustainable if they can perform similarly to conventional diesel fuel. This paper deals with the experimental study carried out to evaluate the engine performance and exhaust emission of diesel engine operated by biodiesel from waste cooking oil at various engine speed. The biodiesel used are known as B5, which contains of 5% of waste cooking oil and 95% of diesel fuel. The other one is B20, which contains of 20% of waste cooking oil plus 80% of diesel. Diesel was used as a comparison purposes. The results show that power and torque for B5 give the closest trend to diesel. In terms of heat release, diesel still dominates the highest value compared to B5 and B20. For exhaust emission, B5 and B20 showed improvement in the reduction of NOx and PM.

scholarly journals Experimental investigation of a small agricultural diesel engine performance using community biodiesel from wild trees

2020 ◽  
Vol 2 (1) ◽  
pp. 9-16
Author(s):  
Nigran Homdoung ◽  
Kittikorn Sasujit ◽  
Natthawud Dussadee ◽  
Rameshprabu Ramaraj
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Exhaust Emission ◽  
Brake Thermal Efficiency ◽  
Cooking Oil ◽  
Wild Tree

The increasing consumption and demand for fossil fuels have more significance than before alarm above its lessening rate and for that reason, stimulated the actions are needed to challenge the issue with an efficient and less polluting alternative fuel for diesel. This study evaluated the performance of an 8.2 kW small diesel engine using three fuels, namely diesel, waste cooking oil biodiesel and wild tree biodiesel, such as granadilla oil biodiesel (GBD) and tung oil biodiesel (TBD). The experimental engine was tested at 1,500 rpm of constant engine speed and 20–80% of engine load. The specific fuel consumption, brake specific energy consumption, brake mean sufficient pressure, brake thermal efficiency, exhaust emission and temperature were evaluated. It was found that the small diesel engine worked well using wild trees biodiesel. The brake means effective pressures were lower by 5–8% and thermal brake efficiency was decreased in the range of 9–15%, compared with diesel fuel. The exhaust emission was lower than Thailand’s industrial standard and slightly higher than waste cooking oil biodiesel and diesel fuel operation. The operation of biodiesel from wild trees is suitable for farmers and is considered feasible for local communities in the future.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

scholarly journals A Review on the Thermochemical Recycling of Waste Tyres to Oil for Automobile Engine Application

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3837
Author(s):  
Mohammad I. Jahirul ◽  
Farhad M. Hossain ◽  
Mohammad G. Rasul ◽  
Ashfaque Ahmed Chowdhury
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Calorific Value ◽  
High Viscosity ◽  
Combustion Efficiency ◽  
Fuel Additive ◽  
Pyrolysis Oil ◽  
Performance And Emission ◽  
Automobile Engines ◽  
Direct Use

Utilising pyrolysis as a waste tyre processing technology has various economic and social advantages, along with the fact that it is an effective conversion method. Despite extensive research and a notable likelihood of success, this technology has not yet seen implementation in industrial and commercial settings. In this review, over 100 recent publications are reviewed and summarised to give attention to the current state of global tyre waste management, pyrolysis technology, and plastic waste conversion into liquid fuel. The study also investigated the suitability of pyrolysis oil for use in diesel engines and provided the results on diesel engine performance and emission characteristics. Most studies show that discarded tyres can yield 40–60% liquid oil with a calorific value of more than 40 MJ/kg, indicating that they are appropriate for direct use as boiler and furnace fuel. It has a low cetane index, as well as high viscosity, density, and aromatic content. According to diesel engine performance and emission studies, the power output and combustion efficiency of tyre pyrolysis oil are equivalent to diesel fuel, but engine emissions (NOX, CO, CO, SOX, and HC) are significantly greater in most circumstances. These findings indicate that tyre pyrolysis oil is not suitable for direct use in commercial automobile engines, but it can be utilised as a fuel additive or combined with other fuels.

Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

Sign in / Sign up

Export Citation Format

Share Document