IMPROVING THE EFFICIENCY OF OPERATING AN OIL WELL WITH BOTTOM WATER

Author(s):  
Ильяс Азаматович Ишбулатов

При разработке водонефтяных зон наблюдается образование конусов подошвенной воды, что ведет к увеличению обводненности скважинной продукции и снижению коэффициента извлечения нефти (КИН). В качестве одного из методов борьбы с данным явлением возможно применение технологии, описанной в патенте RU 2 730 163 C1. В данной статье представлены результаты моделирования данной технологии в гидроди-намическом симуляторе. During the development of oil-water zones, the formation of bottom water cones is observed, which leads to an increase in the water cut of the well production and a decrease in the oil recovery factor. As one of the methods to combat this phenomenon, it is possible to use the technology described in patent RU 2 730 163 C1. This article presents the results of modeling this technology in a hydrodynamic simulator.

2012 ◽  
Vol 591-593 ◽  
pp. 2551-2554
Author(s):  
Jing Xie ◽  
Qiong Liu ◽  
Yan Jiang ◽  
Yu Lin Wang ◽  
Hui Ling Zhu

As a key datum in the petrochemical industry, Water content ratio plays an important role in dehydration, storage selling and petroleum refining. According to the oil well production site, this thesis is based on the oil-water mixture’s density to calculate the water-rate in petroleum, carried on the error analysis to this measuring method, and assessed the scope which this metering equipment is suitable. The wellhead drop back pressure device is effective in monitoring oil wells, to achieve the single well production of display, and when the single well is not working properly, you can discover and resolve problems. The system features are simple structure, easy to carry, stability of Measurement and easy maintenance.


Author(s):  
Dahlia A. Al-Obaidi ◽  
Mohammed S. Al-Jawad

The CO2-Assisted Gravity Drainage process (GAGD) has been introduced to become one of the mostinfluential process to enhance oil recovery (EOR) methods in both secondary and tertiary recovery through immiscibleand miscible mode. Its advantages came from the ability of this process to provide gravity-stable oil displacement forenhancing oil recovery. Vertical injectors for CO2 gas have been placed at the crest of the pay zone to form a gas capwhich drain the oil towards the horizontal producing oil wells located above the oil-water-contact. The advantage ofhorizontal well is to provide big drainage area and small pressure drawdown due to the long penetration. Manysimulation and physical models of CO2-AGD process have been implemented at reservoir and ambient conditions tostudy the effect of this method to improve oil recovery and to examine the most parameters that control the CO2-AGDprocess. The CO2-AGD process has been developed and tested to increase oil recovery in reservoirs with bottom waterdrive and strong water coning tendencies. In this study, a scaled prototype 3D simulation model with bottom waterdrive was used for CO2-assisted gravity drainage. The CO2-AGD process performance was studied. Also the effects ofbottom water drive on the performance of immiscible CO2 assisted gravity drainage (enhanced oil recovery and watercut) was investigated. Four different statements scenarios through CO2-AGD process were implemented. Resultsrevealed that: ultimate oil recovery factor increases considerably when implemented CO2-AGD process (from 13.5%to 84.3%). Recovery factor rises with increasing the activity of bottom water drive (from 77.5% to 84.3%). Also,GAGD process provides better reservoir pressure maintenance to keep water cut near 0% limit until gas flood frontreaches the production well if the aquifer is active, and stays near 0% limit at all prediction period for limited waterdrive.


Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6844
Author(s):  
Hailong Liu ◽  
Fengpeng Lai

Shunbei Oilfield is characterized by substantial heterogeneity and a complex oil–water relationship. The water-oil interface is dynamically changing, and it is a crucial parameter for reserve calculation and evaluation. The main purpose is to analyze the effect of fluid flow in multi-scale media on the water-oil interface. It is well known that the fracture-cavity reservoirs have well-developed fractures and karst caves, and their distribution is complex in Shunbei Oilfield. This paper presents a way to simplify the fracture-cavity system first, then uses a unit of oil wells as a system to study the water-oil interface, which avoids impact on the water-oil interface due to oil production. A detailed step by step procedure for solving the semi-analytical solution of water-oil interface in a fracture-cavity reservoir by using an explicit algorithm and a successive steady-state method is presented. The solution can be used to investigate water-oil interface behavior. In this paper, we validated this method with the actual data for a relatively similar actual reservoir. Sensitivity analyses about the effects of the main parameters including production rates, cave volume and initial oil–water volume ratio on interfacial migration velocity are also presented in detail. The water breaking time of oil wells is fully investigated. The water-oil interface movement chart under different development conditions is established to predict the water-oil interface in the late stage of oil well production and extend the waterless developing period. Being based on this chart, a water breakthrough warning can be realized, and oil recovery can be improved. The findings of the research have led to the conclusion that the rising speed of water-oil interface is proportional to the production rate, on the contrary, it is inversely proportional to cave volume and initial oil–water volume ratio. As well production goes on, the water-oil interface rises at different rates. After the well is put into production for one year, the water-oil interface rises by 16.38%, 12.56% and 4.24% according to the condition that production rate is 10%, the initial oil–water volume ratio is 0.7, and the cave volume is 100 × 104 m3. This method is not only suitable for any period and any well type in the development of Shunbei Oilfield; it also has the function of calculating the real-time water-oil interface of a single well and multi-wells. This new method has the characteristics of easy calculation and high accuracy. The method in this paper can be further developed as it has great applicability in fracture-cavity reservoirs.


2021 ◽  
Author(s):  
Valentina Zharko ◽  
Dmitriy Burdakov

Abstract The paper presents the results of a pilot project implementing WAG injection at the oilfield with carbonate reservoir, characterized by low efficiency of traditional waterflooding. The objective of the pilot project was to evaluate the efficiency of this enhanced oil recovery method for conditions of the specific oil field. For the initial introduction of WAG, an area of the reservoir with minimal potential risks has been identified. During the test injections of water and gas, production parameters were monitored, including the oil production rates of the reacting wells and the water and gas injection rates of injection wells, the change in the density and composition of the produced fluids. With first positive results, the pilot area of the reservoir was expanded. In accordance with the responses of the producing wells to the injection of displacing agents, the injection rates were adjusted, and the production intensified, with the aim of maximizing the effect of WAG. The results obtained in practice were reproduced in the simulation model sector in order to obtain a project curve characterizing an increase in oil recovery due to water-alternating gas injection. Practical results obtained during pilot testing of the technology show that the injection of gas and water alternately can reduce the water cut of the reacting wells and increase overall oil production, providing more efficient displacement compared to traditional waterflooding. The use of WAG after the waterflooding provides an increase in oil recovery and a decrease in residual oil saturation. The water cut of the produced liquid decreased from 98% to 80%, an increase in oil production rate of 100 tons/day was obtained. The increase in the oil recovery factor is estimated at approximately 7.5% at gas injection of 1.5 hydrocarbon pore volumes. Based on the received results, the displacement characteristic was constructed. Methods for monitoring the effectiveness of WAG have been determined, and studies are planned to be carried out when designing a full-scale WAG project at the field. This project is the first pilot project in Russia implementing WAG injection in a field with a carbonate reservoir. During the pilot project, the technical feasibility of implementing this EOR method was confirmed, as well as its efficiency in terms of increasing the oil recovery factor for the conditions of the carbonate reservoir of Eastern Siberia, characterized by high water cut and low values of oil displacement coefficients during waterflooding.


2021 ◽  
pp. 90-104
Author(s):  
L. V. Taranova ◽  
A. G. Mozyrev ◽  
V. G. Gabdrakipova ◽  
A. M. Glazunov

The article deals with the issues of improving the quality of highly watered well production fluid processing using chemical demulsifier reactants at crude oil processing facilities; the analysis of the use of the reactants at the Samotlor field has been made. The article presents the results of the study of the effectiveness of the "Hercules 2202 grade A" and "SNPH-4460-2" demulsifiers in comparison with the indicators of oil and bottom water processing achieved in the presence of the reactants used at existing facilities; their optimal consumption has been determined. The study has shown that the selected demulsifiers provide the required quality of the oil and water under processing at the considered oil processing facilities and can be used along with the basic reactants for these facilities. On the basis of total indicators, the best results have been achieved using "Hercules 2202 grade A" with the improved indicators of water cut and residual oil content in water by 33.9 % and 2.8 % while reducing the reactant consumption by 9.7 % compared to the basic demulsifier.


2021 ◽  
Author(s):  
Effiong Essien ◽  
Uchenna Onyejiaka ◽  
Stanley Onwukwe ◽  
Nnaemeka Uwaezuoke

Abstract Poor formation permeability and near well bore damage may limit water injectivity into the reservoir in a water injection project. This paper seeks to evaluate the effect of radial drilling technique on water injectivity and oil recovery in water flooding operation. Radial drilling technology utilizes hydraulic energy to create lateral perpendicular small holes through the casing into the reservoir. The holes may extend to 100 m (330 ft) into the reservoir to access fresh formations beyond the near wellbore, and damage zone. A black oil simulator (Eclipse 100) was used to modeling a lateral radial drill from the borehole into the reservoir, and that of a conventional perforation of the wellbore respectively. A simulation study was carried out using various presumed radial drill configurations in determining injectivity index, displacement efficiencies, recovery factor and water cut of the process. The determined results were further compared with that of the conventional perforation process case respectively. The results show a significant improvement in water injectivity in radial drill case with the increasing length and number of radials as compared to the conventional wellbore perforation case. The determined Recovery factor shows a progressive increase with increase in the numbers of radials drilled, irrespective of the radial length. However, it was observed that, the more the number and length of the radials drilled in to the reservoir, the higher the water cut from producer wells. Radial Drilling Technology, therefore, has a promising potential to improving water injectivity into the reservoir and thereby optimizing oil recovery in a water flooding operation.


2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Binshan Ju ◽  
Xiaofeng Qiu ◽  
Shugao Dai ◽  
Tailiang Fan ◽  
Haiqing Wu ◽  
...  

The coning problems for vertical wells and the ridging problems for horizontal wells are very difficult to solve by conventional methods during oil production from reservoirs with bottom water drives. If oil in a reservoir is too heavy to follow Darcy’s law, the problems may become more complicated for the non-Newtonian properties of heavy oil and its rheology. To solve these problems, an innovative completion design with downhole water sink was presented by dual-completion in oil and water columns with a packer separating the two completions for vertical wells or dual-horizontal wells. The design made it feasible that oil is produced from the formation above the oil water contact (OWC) and water is produced from the formation below the OWC, respectively. To predict quantitatively the production performances of production well using the completion design, a new improved mathematical model considering non-Newtonian properties of oil was presented and a numerical simulator was developed. A series of runs of an oil well was employed to find out the best perforation segment and the fittest production rates from the formations above and below OWC. The study shows that the design is effective for heavy oil reservoir with bottom water though it cannot completely eliminate the water cone formed before using the design. It is a discovery that the design is more favorable for new wells and the best perforation site for water sink (Sink 2) is located at the upper 1/3 of the formation below OWC.


Author(s):  
Yanlai Li ◽  
Jie Tan ◽  
Songru Mou ◽  
Chunyan Liu ◽  
Dongdong Yang

AbstractFor offshore reservoirs with a big bottom water range, the water cut rises quickly and soon enters the ultra-high water cut stage. After entering the ultra-high water cut stage, due to the influence of offshore production facilities, there are few potential tapping measures, so it is urgent to explore the feasibility study of artificial water injection development. The quasi-three-dimensional and two-dimensional displacement experiments are designed using the experimental similarity criteria according to the actual reservoir parameters. Several experimental schemes are designed, fluid physical properties, interlayer distribution, and development mode according to the actual reservoir physical properties. Through the visualization of experimental equipment, the bottom water reservoir is visually stimulated. The displacement and sweep law of natural water drive and artificial water injection in bottom water reservoir with or without an interlayer, different viscosity, and different well spacing is analyzed. The following conclusions are obtained: (1) For reservoirs with a viscosity of 150 cp. The recovery factor after water injection is slightly higher than before water injection. However, the recovery factor is lower than that without injection production. The reason is that the increment of injection conversion is limited to reduce one production well after injection conversion. (2) For reservoirs with a viscosity of 30 cp. The recovery factor after injection is 39.8%, which is slightly higher than 38.9% without injection. (3) For reservoirs with a viscosity of 150 cp. In the case of the interlayer. The recovery factor after injection is 30.7%, which is significantly higher than 24.8% without injection. (4) After the well spacing of the low-viscosity reservoir is reduced, the recovery factor reaches 46.1%, which is higher than 38.9% of the non-infill scheme. After the infill well in a low-viscosity reservoir is transferred to injection, the recovery factor is 45.6%, which has little change compared with non-injection, and most of the cumulative production fluid is water. The feasibility and effect of water flooding in a strong bottom water reservoir are demonstrated. This study provides the basis for the proposal of production well injection conversion and the adjustment of production parameters in the highest water cut stage of a big bottom water reservoir.


2021 ◽  
Author(s):  
Bahshillo Akramov ◽  
◽  
Sherali Umedov ◽  
Odiljon Khaitov ◽  
Jaloliddin Nuriddinov ◽  
...  

The work is devoted to increasing the degree of depletion of reserves of longterm exploited hydrocarbon deposits on the basis of the obtained results of theoretical and experimental studies of the application of electrodynamic technologies for stimulating the formation and bottomhole formation zone. The electrolysis of formation fluids, water, oil-bearing rocks, is accompanied by a mass transfer, primary and secondary chemical reactions, the formation of all kinds of salts, alkalis and acids, new organic substances and all kinds of surfactants. Not only the liquid is subjected to electrolysis, but also the oil and gas bearing rocks themselves (solid electrolyte). The magnetic and electrical forces arising during the electric treatment of reservoirs make it possible to effectively drain heterogeneous reservoirs and extract residual oil from non-working layers. The work also carried out experiments to study the effect of the electric field on the surface tension coefficient at the oil-water interface. The circumstance of an abrupt change in the surface tension coefficient at the oil-water interface makes it possible in principle to create conditions in the reservoir that make it possible to slow down the cusping processes by applying an electric field of various magnitudes or, in other words, by regulating the amount of mass transfer. In numerical terms, the oil recovery factor without electrophysical treatment was 52.94%. Under electrophysical impact, the oil recovery factor was 94.12%, i.e. equaled to almost complete extraction of oil from the sample. In the field, this figure, of course, will decrease by 2-3 times, but it remains quite high in comparison with other methods of increasing oil recovery. Thus, the studies performed on samples in laboratory conditions indicate the possibility of using constant electric fields to increase oil recovery from depleted watered formations. Electrochemical treatment of the formation can significantly increase the displacement of oil from the formation. The increase in oil displacement reaches 15-20% and more. With the help of water alone, 58% of the oil (of its total volume in the sand) was displaced from the sand, and under electric field with a voltage of 10 V and 20 V, the total amount of displaced oil, respectively, increased to 67 and 83%. Thus, the laboratory studies performed on the samples also indicate the possibility of using constant electric fields to increase oil recovery from depleted watered formations. The carried out theoretical and experimental studies show the possibility of using the technology of electrochemical and electrothermochemical leaching of oilsaturated rocks to intensify oil production. The effectiveness of the recommended technology is especially noticeable in fields that have entered the final stage of development with a high water cut.


2021 ◽  
Vol 6 (4) ◽  
pp. 154-159
Author(s):  
Nataliya N. Tomchuk ◽  
Ekaterina A. Filatova ◽  
Daria S. Burakova ◽  
Mariam R. Karimova ◽  
Nikolay Yu. Tretyakov ◽  
...  

Introduction. Oil field treatment often makes it necessary to combine different methods of well production treatment, taking into account the development regimes and parameters, produced and injected fluids, technical equipment and economic feasibility. The carried-out complex of laboratory tests is aimed at the creation and subsequent destruction of model systems with specified parameters. The list of the considered methods and the temperature regime of the tests are due to the physicochemical parameters and the field specifics. The purpose of this article is to search for an effective method for the primary treatment of well production after SP-flooding — a highly stable oil-water emulsion, additionally stabilized during pumping by means of an ESP. Materials and methods. The laboratory tests helped to develop an optimal mode of creating an artificial emulsion based on oil from BS10-1 reservoir of the Kholmogorsk field in the Yamalo-Nenets Autonomous Okrug, and a surfactant-polymer cocktail, which simulates well production after SP-flooding. The research tested physicochemical methods of destroying oil-water emulsions, such as their dilution with formation fluids, thermal settling, gravitational separation by centrifugation at RPM = 4000–12000 rpm, introduction of demulsifiers, as well as a combined effect, including all of the above approaches. The tested methods were supplied with the calculated values of the oil phase final water-cut, which allowed us to evaluate the effectiveness of the applied approaches to the destruction of model systems. Results. It has been found that not all of the applied approaches provide the extraction of the estimated amount of oil from emulsion systems with varying degrees of dilution by formation fluids. Satisfactory destruction of the emulsion was achieved after 10–20 min of centrifugation at T = 40 °C and RPM within 4000–8000 rpm. The traditional introduction of industrial demulsifiers into the studied systems without additional influences is ineffective. Conclusion. The optimal level of water cut in the oil phase of ≤5% was achieved after diluting the emulsion with formation fluids, with a combined approach to the destruction of the original and diluted emulsion with formation fluids. In addition, the research showed that it is possible to re-use the extracted SP-composition when controlling its physicochemical parameters, taking into account the effect of the introduced additives.


Sign in / Sign up

Export Citation Format

Share Document