CHARACTERISTICS OF WATER RING COMPRESSOR MACHINES VACUUM FISH PUMPING UNITS

Fisheries ◽  
2021 ◽  
Vol 2021 (1) ◽  
pp. 94-98
Author(s):  
Vladimir Naumov ◽  
Nikolay Velikanov
Keyword(s):  
Experimental Data ◽  
Power Consumption ◽  
Least Squares Method ◽  
Vacuum Pump ◽  
Rotor Speed ◽  
Pump Mode ◽  
Working Chamber ◽  
Pumping Units ◽  
Water Ring ◽  
Empirical Constants

The operation of the Samson KS910 pump under various conditions is investigated. The values of empirical constants in mathematical dependencies for calculating pump characteristics were found using the least squares method based on published experimental data. The results of calculating the productivity and power consumption of the Samson KS910 in the vacuum pump mode depending on the pressure in the working chamber at different values of the rotor speed and pressure in the working chamber are presented.

scholarly journals PERFORMANCE OF HIGH-POWER VACUUM FISH PUMPING UNITS

Fisheries ◽  
2020 ◽  
Vol 2020 (4) ◽  
pp. 101-105
Author(s):  
Vladimir Naumov ◽  
Nikolay Velikanov ◽  
Anton Zemlyanov
Keyword(s):  
Differential Equations ◽  
Numerical Method ◽  
High Power ◽  
Vacuum Pump ◽  
Time Intervals ◽  
Pump Operation ◽  
Water Fish ◽  
Pumping Units ◽  
Water Ring

The article describes the features of modeling the stages of pumping a waterfish mixture using a water-ring vacuum pump. The dynamics of pressure changes in reservoir during pump operation for different time intervals is considered. Solutions of the corresponding differential equations are obtained using the numerical method. The calculated characteristics of the process of water-fish mixture pumping into the receiving container are presented.

Research on a Novel Miniature Air Compressor Generating both Compressed Air and Vacuum

2014 ◽  
Vol 1027 ◽  
pp. 253-256
Author(s):  
Jian Hai Han ◽  
Jie Zhang ◽  
Dong Liao Fu ◽  
Zhi Gang Hu
Keyword(s):  
Vacuum Pump ◽  
Operating Principle ◽  
Experimental Results ◽  
System Structure ◽  
Compressed Air ◽  
The Novel ◽  
Pump Mode ◽  
Air Compressor

A new kind of miniature air compressor is proposed in this paper. This compressor can produce both compressed air and vacuum. The system structure, operating principle and experimental characteristics of the novel miniature air compressor are described in detail. The experimental results prove that the shift between air compressor mode and vacuum pump mode is possible and the design of system structure is appropriate.

scholarly journals Relative Entropy Method Applied for the Fatigue Life Distribution of Carbon Fiber/Epoxy Composites

Entropy ◽  
2021 ◽  
Vol 23 (2) ◽  
pp. 224
Author(s):  
Changsheng Yuan ◽  
Yingjie Liang
Keyword(s):  
Experimental Data ◽  
Carbon Fiber ◽  
Relative Entropy ◽  
Least Squares Method ◽  
Entropy Method ◽  
Epoxy Composites ◽  
Order Moment ◽  
Kolmogorov Smirnov ◽  
Relative Entropy Method ◽  
Carbon Fiber Epoxy

This paper verifies the feasibility of the relative entropy method in selecting the most suitable statistical distribution for the experimental data, which do not follow an exponential distribution. The efficiency of the relative entropy method is tested through the fractional order moment and the logarithmic moment in terms of the experimental data of carbon fiber/epoxy composites with different stress amplitudes. For better usage of the relative entropy method, the efficient range of its application is also studied. The application results show that the relative entropy method is not very fit for choosing the proper distribution for non-exponential random data when the heavy tail trait of the experimental data is emphasized. It is not consistent with the Kolmogorov–Smirnov test but is consistent with the residual sum of squares in the least squares method whenever it is calculated by the fractional moment or the logarithmic moment. Under different stress amplitudes, the relative entropy method has different performances.

Effects of vessel baffling on the drawdown of floating solids

2009 ◽  
Vol 63 (2) ◽  
Author(s):  
Joanna Karcz ◽  
Beata Mackiewicz
Keyword(s):  
Experimental Data ◽  
Power Consumption ◽  
Strain Gauge ◽  
High Speed ◽  
Vessel Diameter ◽  
Rushton Turbine ◽  
Agitated Vessel ◽  
Dimensionless Equation ◽  
Inner Diameter ◽  
Floating Particles

AbstractThe effects of baffling of an agitated vessel on the production of floating particles suspension are presented in this paper. Critical agitator speed, needed for particles dispersion in a liquid agitated in a vessel of the inner diameter of 0.295 m, was determined. The just drawdown agitator speeds were defined analogously to the Zwietering criterion. Specific agitation energy was calculated from the power consumption experimental data obtained by means of the strain gauge method. The experiments were carried out for twelve configurations of the baffles differing in number, length and their arrangement in the vessels. The following high-speed impellers were used: up- and downpumping six blade pitched blade turbines, Rushton turbine, and propeller. The impeller was located in the vessel in the height equal to two-thirds or one-third of the vessel diameter from the bottom of the vessel. The results were described in the form of a dimensionless equation.

scholarly journals Determination of parameters for Cauchy’s problem for systems of ODEs with application to biological modelling

BIOMATH ◽  
2016 ◽  
Vol 5 (1) ◽  
pp. 1604231
Author(s):  
A.N. Pete ◽  
Peter Mathye ◽  
Igor Fedotov ◽  
Michael Shatalov
Keyword(s):  
Experimental Data ◽  
Mathematical Models ◽  
Least Squares ◽  
Numerical Method ◽  
Least Squares Method ◽  
Algebraic Equations ◽  
Systems Of Odes ◽  
Determination Of Parameters ◽  
Biological Modelling

An inverse numerical method that estimate parameters of dynamic mathematical models given some information about unknown trajectories at some time is applied to examples taken from Biology and Ecology. The method consisting of determining an over-determined system of algebraic equations using experimental data. The solution of the over-determined system is then obtained using, for example the least-squares method. To illustrate the effectiveness of the method an analysis of examples and corresponding numerical example are presented.

Kinetic equations of creep and damage for description of materials with non-monotonic dependence of fracture strain on stress

2021 ◽  
Vol 23 (3) ◽  
pp. 139-154
Author(s):  
Inna Banshchikova ◽  
Keyword(s):  
Experimental Data ◽  
Comparative Analysis ◽  
Damage Accumulation ◽  
Elevated Temperatures ◽  
Fracture Strain ◽  
Least Squares Method ◽  
Kinetic Equations ◽  
Steel 12Kh18n10t ◽  
Static Mode ◽  
Creep Curves

Introduction. Reducing the level of damage accumulation during pressure treatment of materials at elevated temperatures in creep and close to superplasticity modes in the manufacture of parts can significantly increase its service life in the cold state. Finding temperature and power conditions leading to a reduction in damage of material during the production process and operation is an important task. The purposes of the work: 1) to show the possibility of using the Sosnin-Gorev creep and damage model for alloys with a non-monotonic dependence of strain at fracture on diagrams with creep curves; 2) to carry out comparative analysis of damage accumulation under conditions of uniaxial tension at constant stress and at constant strain rates for alloy with such a dependence. Research methods. Used scalar damage parameter is equated to the normalized deformation, i.e. to the ratio of the current strain to the fracture strain. To find the coefficients of relations creep and damage, the similarity of the creep curves in the normalized values “normalized strain – normalized time”, i.e. the presence of single normalized curve of damage accumulation is checked. The least squares method is used to approximate the experimental data. Numerical integration methods are used for comparative analysis of deformation modes. Results and discussion. Determination of the parameters of the creep and damage equations by the method of a single normalized curve is carried out on the example of experimental data for steel 12Kh18N10T (12Cr18Ni10Ti) at 850 °C, which has a minimum of fracture strain in diagrams with creep curves. Analysis of the static and kinematic modes of deformation for studied material showed that damage accumulation in both cases is practically the same for stresses close to the stress at which this minimum is reached. If the stresses are lower, then the lower level of damage accumulation will be in the kinematic mode; if the stresses above the minimum value, then the static mode will lead to a lower level of damage accumulation. Application. The obtained results can be useful when choosing rational modes of forming structural elements from alloys with a non-monotonic dependence of the fracture strain on stress, as well as in evaluating it for long-term strength during operation.

Commutation Loss in Hydrostatic Pumps and Motors

2021 ◽  
Author(s):  
Robin Mommers ◽  
Peter Achten ◽  
Jasper Achten ◽  
Jeroen Potma
Keyword(s):  
Experimental Data ◽  
Energy Loss ◽  
Simulation Model ◽  
Operating Conditions ◽  
Chamber Pressure ◽  
Working Mechanism ◽  
Working Chamber ◽  
Lumped Parameter ◽  
Long Time ◽  
Pressure Changes

Abstract In mobile hydraulic applications, more efficient machinery generally translates to smaller batteries or less diesel consumption, and smaller cooling solutions. A key part of such systems are hydrostatic pumps and motors. While these devices have been around for a long time, some of the causes of energy loss in pump and motors are still not properly defined. This paper focuses on one of the causes of energy loss in pumps and motors, by identifying the energy loss as a result of the process of commutation. By nature, all hydrostatic pumps and motors have some form of commutation: the transition from the supply port to the discharge port of the machine (and vice versa). During commutation, the connection between the working chamber and the ports is temporarily closed. The chamber pressure changes by compression or decompression that is the result of the rotation of the working mechanism. Ideally, the connection to one of the ports is opened once the chamber pressure equals the port pressure. When the connection is opened too early or too late, energy is lost. This paper describes a method to predict the commutation loss using a lumped parameter simulation model. To verify these predictions, experimental data of a floating cup pump was compared to the calculated values, which show a decent match. Furthermore, the results show that, depending on the operating conditions, up to 50% of all losses in this pump are caused by improper commutation.

Computational Fluid Dynamics Performance Estimation of Turbo Booster Vacuum Pump

2003 ◽  
Vol 125 (3) ◽  
pp. 586-589 ◽  
Author(s):  
H.-P. Cheng ◽  
C.-J. Chen , ◽  
P.-W. Cheng ,
Keyword(s):  
Fluid Dynamics ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Vacuum Pump ◽  
Performance Estimation ◽  
High Mass ◽  
Rotor Speed ◽  
Low Mass ◽  
Pump Inlet

The CFD performance estimation of turbo booster vacuum pump shows the axial vortex and back flow is evident when the mass flow rate is increased. The pressure is increased from the pump inlet to the outlet for the low mass flow rate cases. But for high mass flow rate cases, the pressure is increased until the region near the end of the rotor then decreased. The calculated inlet pressure, compression ratio, and pumping speed is increased, decreased, and decreased, respectively, when the mass flow rate is increased. The pumping speed is increased when the rotor speed is increased.

On the Ability of Structural and Phenomenological Hyperelastic Models to Predict the Mechanical Behavior of Biological Tissues Submitted to Multiaxial Loadings

2012 ◽  
Author(s):  
Mathieu Nierenberger ◽  
Yves Rémond ◽  
Saïd Ahzi
Keyword(s):  
Experimental Data ◽  
Mechanical Behavior ◽  
Strain Energy ◽  
Soft Tissues ◽  
Least Squares Method ◽  
Biological Tissues ◽  
Physical Parameters ◽  
Cauchy Stress ◽  
Specific Loading ◽  
Hyperelastic Models

Medical surgery is currently rapidly improving and requires modeling faithfully the mechanical behavior of soft tissues. Various models exist in literature; some of them created for the study of biological materials, and others coming from the field of rubber mechanics. Indeed biological tissues show a mechanical behavior close to the one of rubbers. But while building a model, one has to keep in mind that its parameters should be loading independent and that the model should be able to predict the behavior under complex loading conditions. In addition, keeping physical parameters seems interesting since it allows a bottom up approach taking into account the microstructure of the material. In this study, the authors consider different existing hyperelastic models based on strain energy functions and identify their coefficients successively on single loading stress-stretch curves. The experimental data used, come from a paper by Zemanek dated 2009 and concerning uniaxial, equibiaxial and plane tension tests on porcine arterial walls taken in identical experimental conditions. To achieve identification, the strain energy function of each model is derived differently to provide an expression of the Cauchy stress associated to each loading case. Firstly the parameters of each model are identified on the uniaxial tension curve using a least squares method. Then, keeping the obtained parameters, predictions are made for the two other loading cases (equibiaxial and plane tension) using the associated expressions of stresses. A comparison of these predictions with experimental data is done and allows evaluating the predictive capabilities of each model for the different loading cases. A similar approach is used after swapping the loading types. Since the predictive capabilities of the models are really dependent on the loading chosen to determine their parameters, another type of identification procedure is set up. It consists in adding the residues over the three loading cases during identification. This alternative identification method allows a better agreement between each model and the various types of experiments. This study evaluated the ability of some classical hyperelastic models to be used for a predictive scope after being identified on a specific loading type. Besides it brought to light some existing models which can describe at best the mechanical behavior of biological tissues submitted to various loadings.

Numerical study of fluid flow and power consumption in a stirred vessel with a Scaba 6SRGT impeller

2011 ◽  
Vol 32 (4) ◽  
pp. 351-366 ◽  
Author(s):  
Houari Ameur ◽  
Mohamed Bouzit ◽  
Mustapha Helmaoui
Keyword(s):  
Experimental Data ◽  
Fluid Flow ◽  
Power Consumption ◽  
Yield Stress ◽  
Short Distance ◽  
Numerical Study ◽  
Stirred Vessel ◽  
Higher Power ◽  
Shear Thinning Fluid ◽  
Good Agreement

Numerical study of fluid flow and power consumption in a stirred vessel with a Scaba 6SRGT impeller The present work deals with agitation of non-Newtonian fluids in a stirred vessel by Scaba impellers. A commercial CFD package (CFX 12.0) was used to solve the 3D hydrodynamics and to characterise at every point flow patterns especially in the region swept by the impeller. A shear thinning fluid with yield stress was modelled. The influence of agitator speed, impeller location and blade size on the fluid flow and power consumption was investigated. The results obtained are compared with available experimental data and a good agreement is observed. It was found that an increase in blade size is beneficial to enlargement of the well stirred region, but that results in an increased power consumption. A short distance between the impeller and the tank walls limits the flow around the agitator and yields higher power consumption. Thus, the precise middle of the tank is the most appropriate position for this kind of impeller.

Sign in / Sign up

Export Citation Format

Share Document