Design and Implementation of an Efficient Biomass Drier System for a Wood Gasification Based Power Plant

2011 ◽  
Vol 110-116 ◽  
pp. 4772-4779
Author(s):  
Kumar Ashlesh ◽  
Rohit Vadera ◽  
K. Ramachandra
Keyword(s):  
Power Plant ◽  
Rural Areas ◽  
Power Plants ◽  
Fossil Fuels ◽  
Waste Heat ◽  
Optimum Level ◽  
Design Development ◽  
Engine Exhaust ◽  
Energy Demands ◽  
Hot Air

The use of woody biomass gasification based power plants to generate electricity is on the rise with the fast depletion of fossil fuels and ever increasing energy demands. An important sub-system of such a plant is the drier which is used to reduce the moisture content of biomass to an optimum level for trouble free and optimum performance of the gasification system. This work concerns with the design, development and implementation of a drier system which utilizes waste heat available from the power plant to dry biomass. The drier designed is simple yet effective in capturing the waste heat from the engine exhaust as well as the radiator hot air. The drier is also easy to implement in rural areas.

scholarly journals Impact of the Wind Turbine on the Parameters of the Electricity Supply to an Agricultural Farm

2021 ◽  
Vol 13 (13) ◽  
pp. 7279
Author(s):  
Zbigniew Skibko ◽  
Magdalena Tymińska ◽  
Wacław Romaniuk ◽  
Andrzej Borusiewicz
Keyword(s):  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Rural Areas ◽  
Power Plants ◽  
Reactive Power ◽  
Supply Voltage ◽  
Common Source ◽  
Voltage Fluctuations ◽  
The Impact

Wind power plants are an increasingly common source of electricity located in rural areas. As a result of the high variability of wind power, and thus the generated power, these sources should be classified as unstable sources. In this paper, the authors attempted to determine the impact of wind turbine operation on the parameters of electricity supplied to farms located near the source. As a result of the conducted field tests, variability courses of the basic parameters describing the supply voltage were obtained. The influence of power plant variability on the values of voltage, frequency, and voltage distortion factor was determined. To estimate the capacity of the transmission lines, the reactive power produced in the power plant and its effect on the value of the power factor were determined. The conducted research and analysis showed that the wind power plant significantly influences voltage fluctuations in its immediate vicinity (the maximum value registered was close to 2%, while the value required by law was 2.5%). Although all the recorded values are within limits specified by the current regulations (e.g., the THD value is four times lower than the required value), wind turbines may cause incorrect operation of loads connected nearby. This applies mainly to cases where consumers sensitive to voltage fluctuations are installed in the direct vicinity of the power plant.

Energy and Exergy Analyses of a Power Plant With Carbon Dioxide Capture Using Multistage Chemical Looping Combustion

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Bilal Hassan ◽  
Oghare Victor Ogidiama ◽  
Mohammed N. Khan ◽  
Tariq Shamim
Keyword(s):  
Carbon Dioxide ◽  
Power Plant ◽  
Natural Gas ◽  
Co2 Capture ◽  
Power Plants ◽  
Waste Heat ◽  
Chemical Looping Combustion ◽  
Chemical Looping ◽  
Operating Pressure ◽  
Efficiency Gain

A thermodynamic model and parametric analysis of a natural gas-fired power plant with carbon dioxide (CO2) capture using multistage chemical looping combustion (CLC) are presented. CLC is an innovative concept and an attractive option to capture CO2 with a significantly lower energy penalty than other carbon-capture technologies. The principal idea behind CLC is to split the combustion process into two separate steps (redox reactions) carried out in two separate reactors: an oxidation reaction and a reduction reaction, by introducing a suitable metal oxide which acts as an oxygen carrier (OC) that circulates between the two reactors. In this study, an Aspen Plus model was developed by employing the conservation of mass and energy for all components of the CLC system. In the analysis, equilibrium-based thermodynamic reactions with no OC deactivation were considered. The model was employed to investigate the effect of various key operating parameters such as air, fuel, and OC mass flow rates, operating pressure, and waste heat recovery on the performance of a natural gas-fired power plant with multistage CLC. The results of these parameters on the plant's thermal and exergetic efficiencies are presented. Based on the lower heating value, the analysis shows a thermal efficiency gain of more than 6 percentage points for CLC-integrated natural gas power plants compared to similar power plants with pre- or post-combustion CO2 capture technologies.

scholarly journals Using adsorption chillers for utilising waste heat from power plants

2019 ◽  
Vol 23 (Suppl. 4) ◽  
pp. 1143-1151 ◽  
Author(s):  
Karol Sztekler ◽  
Wojciech Kalawa ◽  
Sebastian Stefanski ◽  
Jaroslaw Krzywanski ◽  
Karolina Grabowska ◽  
...  
Keyword(s):  
Power Generation ◽  
Energy Efficiency ◽  
Power Plant ◽  
Power Plants ◽  
Waste Heat ◽  
Primary Energy ◽  
Simulation Software ◽  
Coefficient Of Performance ◽  
Low Grade ◽  
Adsorption Chiller

At present, energy efficiency is a very important issue and it is power generation facilities, among others, that have to confront this challenge. The simultaneous production of electricity, heat and cooling, the so-called trigeneration, allows for substantial savings in the chemical energy of fuels. More efficient use of the primary energy contained in fuels translates into tangible earnings for power plants while reductions in the amounts of fuel burned, and of non-renewable resources in particular, certainly have a favorable impact on the natural environment. The main aim of the paper was to investigate the contribution of the use of adsorption chillers to improve the energy efficiency of a conventional power plant through the utilization of combined heat and power waste heat, involving the use of adsorption chillers. An adsorption chiller is an item of industrial equipment that is driven by low grade heat and intended to produce chilled water and desalinated water. Nowadays, adsorption chillers exhibit a low coefficient of performance. This type of plant is designed to increase the efficiency of the primary energy use. This objective as well as the conservation of non-renewable energy resources is becoming an increasingly important aspect of the operation of power generation facilities. As part of their project, the authors have modelled the cycle of a conventional heat power plant integrated with an adsorption chiller-based plant. Multi-variant simulation calculations were performed using IPSEpro simulation software.

A Roadmap for Rural Electrification in Developing Countries Using MiViPPs (Microutility Virtual Power Plants)

2010 ◽  
Author(s):  
Swati Pandey ◽  
Manish Chauhan
Keyword(s):  
Developing Countries ◽  
Renewable Energy ◽  
Power Plant ◽  
Rural Areas ◽  
Power Plants ◽  
Local Level ◽  
Rural Electrification ◽  
Virtual Power ◽  
Effective Manner ◽  
Virtual Power Plants

In this paper we present a road-map for rural electrification in developing countries by means of Renewable Energy based MiViPPs (Microutility virtual power plants). First and foremost a feasibility and viability analysis of the various upcoming and alternative renewable energy options is performed with respect to rural environmental constraints and demands. Renewable Energy based DDG’s (Decentralized Distributed Generation Units) offer the potential for affordable, clean electricity with minimal losses and effective maintenance and local cost recovery. But Independent DDG projects are fraught with their own issues mainly stemming from the unreliable and intermittent nature of the generated power and high costs. We propose an alternative approach to rural electrification which involves off grid DDG units operated at the local level taking advantage of feasible renewable energy technologies, which can effectively serve rural areas and reduce the urgency of costly grid extension. In MIVIPP model, a multitude of decentralized units (renewable energy based units and a non-renewable energy based unit for last mile backup) are centrally controlled and managed as part of an interconnected network, resulting into a virtual power plant that can be operated as a distributed power plant large enough to reliably serve all the local electricity demands in a cost effective manner. Finally, by a set of simulation results we establish how an automated MIVIPP (based on an Intelligent Auto Control System) effectively addresses all the issues pertaining to Dispersed DDG units by leveraging the scalability achieved by mutually augmenting the supplies from different Renewable Energy Based DDG units.

scholarly journals Thermal and Economic Analysis of Multi-Effect Concentration System by Utilizing Waste Heat of Flue Gas for Magnesium Desulfurization Wastewater

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5384 ◽  
Author(s):  
Mingwei Yan ◽  
Yuetao Shi
Keyword(s):  
Wastewater Treatment ◽  
Power Plant ◽  
Economic Analysis ◽  
Magnesium Sulfate ◽  
Flue Gas ◽  
Power Plants ◽  
Waste Heat ◽  
Optimization System ◽  
Benchmark System ◽  
Better Than

Compared with limestone-based wet flue gas desulfurization (WFGD), magnesia-based WFGD has many advantages, but it is not popular in China, due to the lack of good wastewater treatment schemes. This paper proposes the wastewater treatment scheme of selling magnesium sulfate concentrate, and makes thermal and economic analysis for different concentration systems in the scheme. Comparisons of different concentration systems for 300 MW power plant were made to determine which system is the best. The results show that the parallel-feed benchmark system is better than the forward-feed benchmark system, and the parallel-feed optimization system with the 7-process is better than other parallel-feed optimization systems. Analyses of the parallel-feed optimization system with 7-process were made in 300, 600, and 1000 MW power plants. The results show that the annual profit of concentration system for a 300, 600, and 1000 MW power plant is about 2.58 million, 5.35 million, and 7.89 million Chinese Yuan (CNY), respectively. In different concentration systems of the scheme for selling magnesium sulfate concentrate, the parallel-feed optimization system with the 7-process has the best performance. The scheme can make a good profit in 300, 600, and 1000 MW power plants, and it is very helpful for promoting magnesia-based WFGD in China.

Model-Based Analysis of the Start-Up Improvement of a CCPP due to Steam Turbine Warm-Keeping With Air

2019 ◽  
Author(s):  
Dennis Toebben ◽  
Tobias Burgard ◽  
Sebastian Berg ◽  
Manfred Wirsum ◽  
Liu Pei ◽  
...  
Keyword(s):  
Power Plant ◽  
Steam Turbine ◽  
Power Plants ◽  
Cold Start ◽  
Nox Emissions ◽  
Data Set ◽  
Water Steam ◽  
Hot Air ◽  
Start Up ◽  
Low Load

Abstract Combined cycle power plants (CCPP) have many advantages compared to other fossil power plants: high efficiency, flexible operation, compact design, high potential for combined heat and power (CHP) applications and fewer emissions. However, fuel costs are relatively high compared to coal. Nevertheless, major qualities such as high operation flexibility and low emissions distinctly increase in relevance in the future, due to rising power generation from renewable energy sources. An accelerated start-up procedure of CCPPs increases the flexibility and reduces the NOx-emissions, which are relatively high in gas turbine low load operation. Such low load operation is required during a cold start of a CCPP in order to heat up the steam turbine. Thus, a warm-keeping of the thermal-limiting steam turbine results in an accelerated start-up times as well as reduced NOx-emissions and lifetime consumption. This paper presents a theoretical analysis of the potential of steam turbine warm-keeping by means of hot air for a typical CCPP, located in China. In this method, the hot air passes through the steam turbine while the power plant is shut off which enables hot start conditions at any time. In order to investigate an improved start-up procedure, a physical based simplified model of the water-steam cycle is developed on the basis of an operation data set. This model is used to simulate an improved power plant start-up, in which the steam turbine remains hot after at least 120 hours outage. The results show a start-up time reduction of approximately two-thirds in comparison to a conventional cold start. Furthermore, the potential of steam turbine warm-keeping is discussed with regards to the power output, NOx-emissions, start-up costs and lifetime consumption.

scholarly journals Planning of Hybrid Micro-Hydro and Solar Photovoltaic Systems for Rural Areas of Central Java, Indonesia

2020 ◽  
Vol 2020 ◽  
pp. 1-16 ◽  
Author(s):  
Ramadoni Syahputra ◽  
Indah Soesanti
Keyword(s):  
Power Plant ◽  
Optimal Design ◽  
Rural Areas ◽  
Power Plants ◽  
Solar Photovoltaic ◽  
Capital Costs ◽  
Hybrid Power ◽  
Central Java ◽  
Hydropower Potential ◽  
Hybrid Power Plant

This paper proposes the planning of hybrid micro-hydro and solar photovoltaic system for rural areas of Central Java, Indonesia. The Indonesian government has paid great attention to the development of renewable energy sources, especially solar and hydropower. One area that has a high potential for both types of energy is the province of Central Java, located on the island of Java, Indonesia. In this research, we conduct field research to determine the ideal capacity of solar and micro-hydro hybrid power plants, electricity load analysis, and optimal design of hybrid power plants. Data on the potential of micro-hydro plants are obtained by direct measurement on the Ancol Bligo irrigation channel located in Bligo village, Ngluwar district, Magelang regency, Central Java province, Indonesia. Data on solar power potential were obtained from NASA’s database for solar radiation in the Central Java region. Hydropower potential data include channel length, debit, heads, and power potential in irrigation channels originating from rivers. These data are used to design an optimal hybrid power plant. The method used to obtain the optimal design of a hybrid power plant system is based on the analysis of capital costs, grid sales, cost of energy, and net present cost. Based on the parameters of the analysis, the composition of the optimal generator for the on-grid scheme to the distribution network can be determined. The results showed that hybrid power plants were able to meet the needs of electrical energy in the villages around the power plant and that the excess energy could be sold to national electricity providers.

Waste Heat Recovery and Saving Fresh Water Consumption in Power Plants

2012 ◽  
Author(s):  
Kwangkook Jeong
Keyword(s):  
Power Plant ◽  
Fresh Water ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Power Plants ◽  
Waste Heat ◽  
Combined Cycle ◽  
Water Recovery ◽  
Cooling Effects ◽  
Power Plant Cooling

A section to delineate ‘waste heat recovery’ has been written to contribute for the ASME Power Plant Cooling Specification/Decision-making Guide to be published in 2013. This paper informs tentative contents for the section on how to beneficially apply waste heat and water recovery technology into power plants. This paper describes waste heat recovery in power plant, current/innovative technologies, specifications, case study, combined cycle, thermal benefits, effects on system efficiency, economic and exergetic benefits. It also outlines water recovery technologies, benefits in fresh water consumptions, reducing acids emission, additional cooling effects, economic analysis and critical considerations.

Small Scale Prototype Biomass Drying System for Co-Combustion With Coal

2013 ◽  
Author(s):  
Heather Roberts ◽  
Mitch Favrow ◽  
Jesse Coatney ◽  
David Yoe ◽  
Chenaniah Langness ◽  
...  
Keyword(s):  
Power Plant ◽  
Thermoelectric Power ◽  
Renewable Resources ◽  
Power Plants ◽  
Waste Heat ◽  
Coefficient Of Performance ◽  
Small Scale ◽  
Drying Time ◽  
Thermoelectric Power Plants ◽  
Drying System

Thermoelectric power plants burn thousands of tons of non-renewable resources every day to heat water and create steam, which drives turbines that generate electricity. This causes a significant drain on local resources by diverting water for irrigation and residential usage into the production of energy. Moreover, the use of fossil reserves releases significant amounts of greenhouse and hazardous gases into the atmosphere. As electricity consumption continues to grow and populations rise, there is a need to find other avenues of energy production while conserving water resources. Co-combusting biomass with coal is one potential route that promotes renewable energy while reducing emissions from thermoelectric power plants. In order to move in this direction, there is a need for a low-energy and low-cost system capable of drying materials to a combustion appropriate level in order to replace a significant fraction of the fossil fuel used. Biomass drying is an ancient process often involving the preservation of foods using passive means, which is economically efficient but slow and impractical for large-scale fuel production. This effort, accomplished as an undergraduate capstone design project, instead implements an active drying system for poplar wood using theorized waste heat from the power plant and potentially solar energy. The use of small-scale prototypes demonstrate the principles of the system at a significantly reduced cost while allowing for calculation of mass and energy balances in the analysis of drying time, Coefficient of Performance, and the economics of the process. Experimental tests illustrate the need to distribute air and heat evenly amongst the biomass for consistent drying. Furthermore, the rotation of biomass is critical in order to address the footprint of the system when placing next to an existing thermoelectric power plant. The final design provides a first step towards the refinement and development of a system capable of efficiently returning an amount of biomass large enough to replace non-renewable resources. Finally, an innovative methodology applied to the dryer is discussed that could recover water evaporated from the biomass and utilize it for agricultural purposes or within the power plant thermodynamic cycle.

Paper 11: Feed Pumps for Modern Steam Boiler Applications, Design, Development, and Operation

1969 ◽  
Vol 184 (14) ◽  
pp. 108-148
Author(s):  
P. S. Neporozhnii ◽  
A. K. Kirsh
Keyword(s):  
Power Plant ◽  
Power Plants ◽  
Operating Conditions ◽  
Steam Boiler ◽  
Design Development ◽  
Feed Pump ◽  
Design Features ◽  
Power Plant Equipment ◽  
Plant Equipment

This paper describes the operating conditions which form the basis for determining the various types of feed pump units needed to equip the main power plant equipment in the U.S.S.R. The principles upon which the feed pump groups are selected, according to the type of equipment installed in different power plants, are considered. The system diagrams and design features of the feed pumps are presented, together with descriptions of how they are driven.

Sign in / Sign up

Export Citation Format

Share Document