Experimental Study on Softening Treatment of Weak Acid Hydrogen Type Resin to Viscous Oil Sewage

2014 ◽  
Vol 535 ◽  
pp. 692-700
Author(s):  
Xiao Ge ◽  
Ying Xu ◽  
Bin Dong ◽  
Zu Wen Liu
Keyword(s):  
Experimental Study ◽  
Ion Exchange ◽  
Ph Value ◽  
Weak Acid ◽  
Production Plant ◽  
Test Results ◽  
Softening Effect ◽  
Exchange Column ◽  
Viscous Oil ◽  
Softened Water

This essay presents an experimental study about softening effect of weak acid hydrogen type resin on viscous oil sewage of an oil production plant through ion exchange technique, and the test results show that: when the first level of ion exchange column adopts weak acid hydrogen type resin and the second level adopts weak acid sodium type resin, pH value of final effluent is 6.7~7.0, and average hardness is 0.02 mg·L-1; when the first-level resin is invalid and regenerated, with washing for 12h at the flow rate of 10BV/H by softened water after acid feeding, about 50% of the weak acid hydrogen type resin is transformed into sodium type, and after being put into operation, the pH value the hardness and other indexes of the first-level and second-level effluent conform to national requirements. It is thus clear that: compared with the traditional process of the first-level exchange column adopting the weak acid sodium type resin, the first-level exchange column adopting the weak acid hydrogen type resin has better softening effect on viscous oil sewage, reduces alkali transformation steps during regeneration, and reduces alkali cost and environmental pollution.

DIP quality influenced by process water quality

TAPPI Journal ◽  
2014 ◽  
Vol 13 (9) ◽  
pp. 51-60
Author(s):  
DENNIS VOSS ◽  
HANS-JOACHIM PUTZ ◽  
SAMUEL SCHABEL
Keyword(s):  
Water Quality ◽  
Surface Tension ◽  
Ph Value ◽  
Water Hardness ◽  
Process Water ◽  
Test Results ◽  
Negative Effects ◽  
Water Parameters ◽  
Effects Of Ph ◽  
Contamination Levels

The need for deinking mills to reduce their fresh water consumption has resulted in higher loads of various contaminants in the process water. Lower recovered paper quality also leads to higher contamination levels in the mills. This higher load has an influence on achievable target brightness. The objective of the work was to determine and explain the main reasons for relatively poor deinked pulp quality or poor deinking potential based on the influence of recovered paper composition and process water quality. The process water parameters significantly affect the deinking potential of recovered paper. The test results showed the negative effects of increased water hardness. For standard recovered paper mixtures, flotation selectivity is higher with increasing flotation pH-value. Good results were realized for standard recovered paper with low hardness, low surface tension, and high pH-value. The results for recovered paper containing flexo newsprint could be slightly improved with low hardness, low surface tension, and low pH-value. The results of the test program using design of experiments showed interacting effects of pH-value and surface tension on luminosity and flotation selectivity.

scholarly journals Experimental Study on Improvement of Marine Soft Soil with Alkali Residue

2018 ◽  
Vol 53 ◽  
pp. 04021
Author(s):  
SHAO Yong ◽  
LIU Xiao-li ◽  
ZHU Jin-jun
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Soft Soil ◽  
Compressive Modulus ◽  
Engineering Properties ◽  
Test Results ◽  
Use Of Resources ◽  
One Year

Industrial alkali slag is the discharge waste in the process of alkali production. About one million tons of alkali slag is discharged in China in one year. It is a burden on the environment, whether it is directly stacked or discharged into the sea. If we can realize the use of resources, it is a multi-pronged move, so alkali slag is used to improve solidified marine soft soil in this paper. The test results show that the alkali residue can effectively improve the engineering properties of marine soft soil. Among them, the unconfined compressive strength and compressive modulus are increased by about 10 times, and the void ratio and plasticity index can all reach the level of general clay. It shows that alkali slag has the potential to improve marine soft soil and can be popularized in engineering.

Selective Leaching Nickel from the Pre-Reduced Limonitic Laterite Ore at Atmospheric Pressure

2012 ◽  
Vol 560-561 ◽  
pp. 494-498
Author(s):  
Yong Feng Chang ◽  
Chuan Lin Fan ◽  
Bin Chuan Li ◽  
Xiu Jing Zhai ◽  
Ting An Zhang
Keyword(s):  
Atmospheric Pressure ◽  
Ph Value ◽  
Test Results ◽  
Selective Leaching ◽  
Nickel Extraction ◽  
Extraction Degree ◽  
Leaching Solution ◽  
Novel Method ◽  
Leaching Condition ◽  
Laterite Ore

In this paper a novel method for selective leaching nickel from pre-reduced laterite ore at atmospheric pressure was reported. The reduced calcine was leached in thin acid liquor to liberate the nickel and iron together firstly. By properly controlling the leaching condition, the leached iron ion could hydrolyze as goethite precipitate and regenerate the acid consumed in the leaching procedure. Finally, the nickel is selectively extracted into the leaching solution. The main factors in the leaching process, such as reduction degree of the laterite ore, acidity of the leaching solution were investigated as influence on the nickel extraction. The test results showed that selectively leaching of nickel could be achieved with an extraction degree up to 90% by reducing most of the iron in the lateritic ore to wuestite and controlling the pH value of the leaching solution below 2.5.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Bromide Ion Exchange with a Keggin Polyoxometalate on Functionalized Polymeric Membranes: A Theoretical and Experimental Study

2014 ◽  
Vol 118 (9) ◽  
pp. 2396-2404 ◽  
Author(s):  
G. De Luca ◽  
F. Bisignano ◽  
A. Figoli ◽  
F. Galiano ◽  
E. Furia ◽  
...  
Keyword(s):  
Experimental Study ◽  
Ion Exchange ◽  
Polymeric Membranes ◽  
Bromide Ion ◽  
Keggin Polyoxometalate

Experimental Study of Improved Tool in High Manganese Steel Drilling

2010 ◽  
Vol 97-101 ◽  
pp. 1863-1866
Author(s):  
Liang Yang ◽  
Li Xu
Keyword(s):  
Experimental Study ◽  
Simulation Method ◽  
Manganese Steel ◽  
Drill Bit ◽  
Test Results ◽  
Comparison Analysis ◽  
High Manganese ◽  
Drilling Force ◽  
High Manganese Steel ◽  
Drill Tool

Performance of tool has always been a puzzle in the course of high manganese steel drilling. In this paper, improvement of drill tool is been done on drill bit structure and parameters of cutting tip by means of analyzing geometric parameter. By utilizing simulation method correctly, the influence of bit parameter on drilling force is analyzed. Meanwhile, by adopting the way of dividing into groups, comparison experiment between improved and no improved has been done. The comparison analysis of test results is carried out including tool life, wear and drilling force. The conclusion showed that the improved bit has better performance.

Sign in / Sign up

Export Citation Format

Share Document