Effect of Sintering Temperature on Microstructure and Mechanical Properties of Ti-Nb-Sn-HA Composites Produced by Powder Metallurgy

2014 ◽  
Vol 625 ◽  
pp. 180-183 ◽  
Author(s):  
Wan Nurul Syaza Wan Nawai ◽  
Norhanida Awang Kasani ◽  
Razif Nordin ◽  
Zainal Arifin Ahmad ◽  
Saidatulakmar Shamsuddin
Keyword(s):  
Mechanical Properties ◽  
Sintering Temperature ◽  
Metal Powders ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Rotating Speed ◽  
Microstructure And Mechanical Properties ◽  
Increasing Trend ◽  
Difference Temperature ◽  
Vickers Micro Hardness

The influence of difference sintering temperature: 900°C, 1000°C, 1100°C, 1200°C and 1300°C on the microstructure and mechanical properties of a biomedical Ti–35Nb-2.5Sn-15HA (wt.%) composite was investigated with regard to densification, porosity and hardness. Ti composite process was performed on elemental metal powders by blend the powder mixture at a rotating speed of 200 rpm mixing for 10 min and then sintered with difference temperature. The composites produced were then subjected to the following test: densification, Vickers micro hardness, microstructure by using SEM and X-ray diffraction analysis. Result indicated that the densification and Vickers micro hardness shown a decrease trend with the increasing of temperature due to the increasing trend of porosity up to 73%.

Effects of NiO Nanoparticles on Physical and Mechanical Properties of BNKT Lead-Free Ceramics

2017 ◽  
Vol 866 ◽  
pp. 282-286 ◽  
Author(s):  
Chatchai Kruea-In ◽  
Suchittra Inthong ◽  
Wilaiwan Leenakul
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Micro Hardness ◽  
Nio Nanoparticles ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Hardness Tester ◽  
Lead Free Ceramics ◽  
Vickers Micro Hardness

In this research, The effects of NiO nanoparticles on the physical and mechanical properties of Bi0.5(Na0.81,K0.19)0.5TiO3 (BNKT) were investigated. The ceramics were synthesized by solid state reaction technique. The powder of BNKT was calcined at 850 °C for 4 h. The ceramics of BNKT/x NiO vol.% ( i.e. x= 0.0, 1.0, 2.0 and 3.0) were sintered at 1000-1150 °C for 2 h for optimize condition. Densification, phase formation, microstructure and micro hardness of samples were characterized via Archimedes method, X-ray diffraction techniques (XRD), scanning electron microscope (SEM) and Vickers micro hardness tester. The X-ray diffraction analysis of the ceramics suggests that all samples exhibited a perovskite structure. Densification of samples tended to increase with increasing amount of NiO content with minimun at 1.0 vol.% NiO additive. The NiO additive influenced densification as well as the mechanical properties of the samples. The results of this research suggest that NiO nanoparticles have influence on physical and mechanical properties of BNKT ceramics.

scholarly journals Influence of Sintering Process on Microstructure and Mechanical Properties of Ti(C,N)-Based Cermet

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 3938
Author(s):  
Kaixun Ji ◽  
Yanxin Meng ◽  
Fuzeng Wang ◽  
Yousheng Li
Keyword(s):  
Mechanical Properties ◽  
Sintering Temperature ◽  
Holding Time ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Vacuum Sintering ◽  
Material Microstructure ◽  
Cermet Material ◽  
Hardness Tester ◽  
Microstructure And Mechanical Properties

In this study, a Ti(C,N)-based cermet material was prepared through vacuum sintering. The research also investigates how holding time and maximum sintering temperature influence the material microstructure and mechanical properties. X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) were used to analyze the composition of the cermet. The microstructure of the cermet was analyzed and examined using a scanning electron microscope (SEM). A Vickers hardness tester was used to test the mechanical properties of the materials. As indicated by testing results, the hardness of the material decreases as the temperature of sintering increases, and its fracture toughness increases gradually as holding time increases. Ti(C,N)-based cermet manifested the optimal mechanical properties when sintering was conducted under 1400 °C with 80 min of holding time. Moreover, the material microstructure is significantly affected by the sintering process. The grain size of Ti(C,N) cermets increases as the sintering temperature increases. The microstructure tends to be uniform and the complete core-rim structures are established as the holding time increases.

Micro-Hardness and Morphology of LDPE Influenced by Beta Radiation

2014 ◽  
Vol 606 ◽  
pp. 253-256 ◽  
Author(s):  
Martin Ovsik ◽  
Petr Kratky ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Hardness Test ◽  
Polymer Materials ◽  
Beta Radiation ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Depth Sensing ◽  
Surface Layers ◽  
Hardness Values ◽  
Different Doses

This article deals with the influence of different doses of Beta radiation to the structure and mico-mechanical properties of Low-density polyethylene (LDPE). Hard surface layers of polymer materials, especially LDPE, can be formed by radiation cross-linking by β radiation with doses of 33, 66 and 99 kGy. Material properties created by β radiation are measured by micro-hardness test using the DSI method (Depth Sensing Indentation). Individual radiation doses caused structural and micro-mechanical changes which have a significant effect on the final properties of the LDPE tested. The highest values of micro-mechanical properties were reached at radiation dose of 66 and 99 kGy, when the micro-hardness values increased by about 21%. The changes were examined and confirmed by X-ray diffraction.

scholarly journals Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Kuai Zhang ◽  
Yungang Li ◽  
Hongyan Yan ◽  
Chuang Wang ◽  
Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Hot Press ◽  
Microstructure And Mechanical Properties ◽  
Powder Particles ◽  
Hot Press Sintering ◽  
Sintering Method

An Fe/FeAl2O4 composite was prepared with Fe-Fe2O3-Al2O3 powder by a hot press sintering method. The mass ratio was 6:1:2, sintering pressure was 30 MPa, and holding time was 120 min. The raw materials for the powder particles were respectively 1 µm (Fe), 0.5 µm (Fe2O3), and 1 µm (Al2O3) in diameter. The effect of sintering temperature on the microstructure and mechanical properties of Fe/FeAl2O4 composite was studied. The results showed that Fe/FeAl2O4 composite was formed by in situ reaction at 1300 °C–1500 °C. With the increased sintering temperature, the microstructure and mechanical properties of the Fe/FeAl2O4 composite showed a change law that initially became better and then became worse. The best microstructure and optimal mechanical properties were obtained at 1400 °C. At this temperature, the grain size of Fe and FeAl2O4 phases in Fe/FeAl2O4 composite was uniform, the relative density was 96.7%, and the Vickers hardness and bending strength were 1.88 GPa and 280.0 MPa, respectively. The wettability between Fe and FeAl2O4 was enhanced with increased sintering temperature. And then the densification process was accelerated. Finally, the microstructure and mechanical properties of the Fe/FeAl2O4 composite were improved.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Effects of MgO and Y2O3 on the Microstructure and Mechanical Properties of Al2O3 Ceramics

2013 ◽  
Vol 589-590 ◽  
pp. 572-577 ◽  
Author(s):  
Hua He Liu ◽  
Han Lian Liu ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Ya Cong Chai
Keyword(s):  
Mechanical Properties ◽  
Sintering Temperature ◽  
Hot Press ◽  
Composite Ceramics ◽  
Microstructure And Mechanical Properties ◽  
Suitable Amount ◽  
Hot Press Sintering ◽  
Grains Refinement ◽  
Better Than

Al2O3-MgO, Al2O3-Y2O3 and Al2O3-MgO-Y2O3 composite ceramics were fabricated respectively by hot-press sintering technique. With the analysis of the mechanical properties and microstructure, it was found that single additive MgO could be more favorable to the grains’ refinement and densification than Y2O3; the composite additive including both MgO and Y2O3 was better than single additive MgO or Y2O3, because their interactions could improve the mechanical properties of the Al2O3 ceramics; The sintering temperature could be reduced by adding the suitable amount of composite additives.

Effect of sintering temperature on the microstructure and mechanical properties of Ti(C, N)-based cermets

2007 ◽  
Vol 46 (9-10) ◽  
pp. 449-453 ◽  
Author(s):  
Yonglin Yan ◽  
Yong Zheng ◽  
Haijun Yu ◽  
Haijian Bu ◽  
Xin Cheng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Sintering Temperature ◽  
Microstructure And Mechanical Properties

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Sign in / Sign up

Export Citation Format

Share Document