An Experimental Investigation on the Mechanical Properties of Glass Fiber Woven Roving Fabrics/Chopped Strand Mats Hybrid Composites Manufactured by Different Processes

2014 ◽  
Vol 664 ◽  
pp. 8-13
Author(s):  
Jun Tang ◽  
Zhi Hua Wu ◽  
Su Li Xing ◽  
Qing Zheng ◽  
Zheng Shen
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Resin Composite ◽  
Unsaturated Polyester ◽  
Composite Panels ◽  
Molding Process ◽  
Glass Fiber Reinforced

In this paper, the mechanical properties of glass fiber reinforced unsaturated polyester resin composite panels were investigated. To understand the effect of chopped strand mats on the mechanical properties of the composites, specimens with certain volume fraction of chopped strand mats manufactured by Vacuum Infusion Molding Process (VIMP) and Hand Lay-up techniques were tested under tensile, bending and impact loadings respectively. It was observed that the chopped strand mats enhanced effectively the mechanical properties of the composite panels manufactured by Hand Lay-up method, while the mechanical properties of the composite panels manufactured by VIMP decreased.

scholarly journals Mechanical Properties of Longitudinal Basalt/Woven-Glass-Fiber-reinforced Unsaturated Polyester-Resin Hybrid Composites

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2211
Author(s):  
S.M. Sapuan ◽  
H.S. Aulia ◽  
R.A. Ilyas ◽  
A. Atiqah ◽  
T.T. Dele-Afolabi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Hybrid Composites ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Unsaturated Polyester Resin ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Woven Glass Fiber

This work represents a study to investigate the mechanical properties of longitudinal basalt/woven-glass-fiber-reinforced unsaturated polyester-resin hybrid composites. The hybridization of basalt and glass fiber enhanced the mechanical properties of hybrid composites. The unsaturated polyester resin (UP), basalt (B) and glass fibers (GF) were fabricated using the hand lay-up method in six formulations (UP, GF, B7.5/G22.5, B15/G15, B22.5/G7.5 and B) to produce the composites, respectively. This study showed that the addition of basalt to glass-fiber-reinforced unsaturated polyester resin increased its density, tensile and flexural properties. The tensile strength of the B22.5/G7.5 hybrid composites increased by 213.92 MPa compared to neat UP, which was 8.14 MPa. Scanning electron microscopy analysis was used to observe the fracture mode and fiber pullout of the hybrid composites.

scholarly journals Mechanical behavior of transparent fiber reinforced polyester composites at extreme temperatures

2018 ◽  
Author(s):  
◽  
Saad Ramadhan Ahmed
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Fiber Reinforced Polymers ◽  
Extreme Conditions ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
The Impact

Selecting materials for harsh or extreme environmental conditions can be a challenge. The combination of a harsh environment, large forces over extended periods and the need for lowest possible cost restricts the choice of materials. One potential material is glass fiber reinforced polymers that are widely used in structural systems as load bearing elements, they are relatively low cost and can be tailored to achieve a range of mechanical properties. This investigation presents the preparation of transparent glass fiber reinforced unsaturated polyester composite and the evaluation of its optical and mechanical properties under extreme conditions of temperature. The polyester resin was reinforced with E-glass fibers to manufacture a composite using the hand layup method. Transparency was achieved by modifying the refractive index of the polyester resin to match that of the glass fibers. This investigation also presents the evaluation of glass fiber reinforced unsaturated polyester under quasi-static tension loading and puncture testing using a drop weight at extreme conditions. The results showed that the reinforced composite had a higher fracture stress and chord modulus at all temperatures ranging from +60 [degree]C to -80 [degree]C as compared to the unreinforced polyester matrix. The unreinforced polyester has a higher stiffness at lower temperatures due to reduced polymer chain mobility and higher clamping pressure of the matrix on the glass fiber reinforcement. The damage created by the impact reduces with decreasing temperatures, while the energy absorb remains constant with temperature.

Mechanical properties of plain woven kenaf/glass fiber reinforced polypropylene hybrid composites

2019 ◽  
Vol 61 (11) ◽  
pp. 1095-1100 ◽  
Author(s):  
Sivakumar Dhar Malingam ◽  
Kathiravan Subramaniam ◽  
Ng Lin Feng ◽  
Siti Hajar Sheikh MD Fadzullah ◽  
Sivaraos Subramonian
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Hybrid Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Woven Kenaf

Fabrication and Characterization of E-Glass Fiber Reinforced Unsaturated Polyester Resin Based Composite Materials

2019 ◽  
Vol 24 ◽  
pp. 1-7
Author(s):  
Md. Naimul Islam ◽  
Harun Ar-Rashid ◽  
Farhana Islam ◽  
Nanda Karmaker ◽  
Farjana A. Koly ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Bending Strength ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Tensile Modulus ◽  
Unsaturated Polyester Resin ◽  
Fiber Reinforced ◽  
Bending Modulus

E-glass fiber mat reinforced Unsaturated Polyester Resin (UPR)-based composites were fabricated by conventional hand lay-up technique. The fiber content was varied from 5 to 50% by weight. Mechanical properties (tensile and bending) of the fabricated composites were investigated. The tensile strength (TS) of the 5% and 50% fiber reinforced composites was 32 MPa and 72 MPa, respectively. Similarly, tensile modulus, bending strength and bending modulus of the composites were increased by the increase of fiber loading. Interfacial properties of the composites were investigated by scanning electron microscopy (SEM) and the results revealed that the interfacial bond between fiber and matrix was excellent. Keywords: Unsaturated Polyester Resin, Mechanical Properties, E-glass Fibers, Composites, Polymer.

Fatigue and tensile behaviors of fiber-reinforced thermosetting composites embedded with nanoparticles

2018 ◽  
Vol 53 (6) ◽  
pp. 709-718 ◽  
Author(s):  
Moustafa Mahmoud Yousry Zaghloul ◽  
Yasser S Mohamed ◽  
Hassan El-Gamal
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Cellulose Nanocrystals ◽  
Testing Machine ◽  
Material Design ◽  
Fatigue Properties ◽  
Fiber Reinforced ◽  
Molding Process ◽  
Glass Fiber Reinforced ◽  
Wide Range

The development of studying nanocomposites has grown up rapidly in the last decade. The objective of the current research is to study the influence of incorporating cellulose nanocrystals on the mechanical properties of polyester resins, as well as to develop continuous filament e-glass fiber-reinforced polyester nanocomposites, which combine traditional composites with the added advantages of nanocomposites. Cellulose nanocrystals were uniformly dispersed into the polyester resin by an ultrasonic processor. The incorporation and dispersion of cellulose nanocrystals were a state-of-the-art method aimed at overcoming poor dispersion problems at low weight fractions of nanoparticles. Three weight percentages of cellulose nanocrystals were prepared, which were 2%, 4% and 6%. Fatigue and tensile specimens were manufactured by resin transfer molding process. Cellulose nanocrystals were fully characterized by using X-ray diffraction, transmission electron microscopy, Fourier-transform infrared spectroscopy and zeta-sizer analysis. The optimum incorporation percentage of cellulose nanocrystals was used to prepare glass fiber-reinforced polyester specimens containing cellulose nanocrystals. Tensile and fatigue behaviors of glass fiber-reinforced polyester composites were evaluated by means of universal testing machine and rotating bending fatigue machine. A series of testing specimens for each property was examined in accordance with the corresponding ASTM and JIS standards. The experimental results showed that the addition of 4% cellulose nanocrystals to polyester matrix lead to the optimum tensile and fatigue properties. Mechanical properties were improved through the enhanced material design and proper selection of compatible nanoparticles, and adding cellulose nanocrystals in a weight fraction that does not affect the mechanical properties of glass fiber-reinforced polyester nanocomposites negatively. The presented design of material and geometry have shown promising results for wide range of applications, particularly in biomedical industry, energy and electronics.

Tensile Strength Matrix Composite Waste Glass Fiber Reinforced Plastics

2014 ◽  
Vol 69 (6) ◽  
Author(s):  
A. Mataram
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Natural Fibers ◽  
Plastic Waste ◽  
Molding Method ◽  
Reinforced Plastics ◽  
Glass Fiber Reinforced ◽  
Composite Reinforcement

Polypropylene (PP) including a type of plastic which ranks second on the most number of types of plastic waste after the type of High Density Polyethylene (HDPE). Glass fibers have superior mechanical properties of natural fibers. Because it has good mechanical properties, glass fibers currently plays an important role in the use of composite reinforcement. Mechanical properties of glass fiber owned and PP waste in environmental conditions that more conditions, it can be utilized as a composite reinforcement and matrix materials. This research was conducted by of injection molding method. The comparison between the volume fraction of the glass fiber matrix of type PP plastic waste with variation 0% fibers 100% matrixs, 10% fibers 90% matrixs, 20% fibers 80% matrixs, 30% fibers 70% matrixs, 40% fibers 60% matrixs, and 50 % fibers 50% matrixs. The optimum conditions obtained in this study was the comparison of variation occurs in 50% fibers volume fractions of 50% matrixs were: tensile stress was 24.30 N/mm2, tensile strain was 13.60%.

Sign in / Sign up

Export Citation Format

Share Document