scholarly journals Tensile Strength of Banana Fiber Reinforced Epoxy Composites Materials

2015 ◽  
Vol 776 ◽  
pp. 260-263 ◽  
Author(s):  
Agustinus Purna Irawan ◽  
I. Wayan Sukania
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Epoxy Composite ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Fiber Reinforced ◽  
Banana Fiber ◽  
Composites Materials ◽  
Biocomposite Material

Indonesia is one of countries with the potential for abundant natural resources, especially natural fibers. The potential of Indonesian natural fibers abundant is not fully put to good use to increase social welfare. One of the natural fibers that have the potential to be developed is the banana fiber. Banana fiber has potential in abundance and can be developed as a biocomposite material that is strong, inexpensive, environmentally friendly, and can be recycled. This study aims to produce a tensile strength of Banana Fiber Reinforced Epoxy Composite Materials (BFRECM). Testing of the tensile strength refers to the ASTM D 3039 / D3039M. Based on the research results, obtained the tensile strength of BFRECM (62.3 ± 0.67) MPa and modulus of elasticity (8.72 ± 1.12) GPa. Tensile strength obtained will be referred for further study of natural fiber composites.

scholarly journals Development and Testing of Pine Apple and Glass Fiber Reinforced Epoxy Hybrid Composites

2019 ◽  
Vol 8 (3) ◽  
pp. 2450-2453
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Fiber Reinforced ◽  
Synthetic Fibers ◽  
Glass Fiber Reinforced

Usage of Natural Fiber Composites (NFC) is increased rapidly due to the bio degradability nature of the fibers. These natural fibers are mixed with synthetic fibers to obtain better mechanical properties. In this study, pine apple and glass fiber reinforced epoxy composites are developed and their mechanical properties were evaluated. Composites were prepared by varying the fibers content and by using hand layup process with glass moulds of size 160 x 160 x 3 mm3 . The obtained laminates were sliced as per the ASTM criterion to test the properties. Higher glass fiber content in the composite specimen obtained higher mechanical properties. The composites can be utilized for the purpose of manufacturing components like doors panels, desks, roof tops etc.

Tensile Strength of Banana – Bamboo – Glass Fiber Reinforced Natural Fiber Composites

2014 ◽  
Vol 592-594 ◽  
pp. 1195-1199
Author(s):  
Ashwin Sailesh ◽  
C. Shanjeevi ◽  
J.Jeswin Arputhabalan
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Orientation ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Natural Fiber Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced

The developments in the field of composite materials are growing tremendously day by day. One such development is the use of natural fibers as reinforcement in the composite material. This is attributed to the fact that natural fibers are environmental friendly, economical, easily available and non-abrasive. Mixing of natural fiber with Glass Fibers is finding increased applications. In this present investigation Banana – Bamboo – Glass fiber reinforced natural fiber composites is fabricated by Hand – Layup technique with varying fiber orientation such as [0°G, 90°BM, 0°BN, 0°G], [0°G, 0°BM, +45°BN, 0°G] and [0°G, 0°BM, 90°BN, 0°G] and are tested for its tensile strength. The tensile strength of the fabricated composites is evaluated. The results indicated that the natural fiber composite with the fiber orientation of [0°G, 0°BM, 90°BN, 0°G] can withstand more load when compared to the samples with other fiber orientation. Nomenclature Used: BN – Banana fiber BM – Bamboo fiber G – Glass fiber

Determination of Delamination and Tensile Strength of Drilled Natural Fiber Reinforced Composites

2014 ◽  
Vol 592-594 ◽  
pp. 134-138 ◽  
Author(s):  
G. Dilli Babu ◽  
K. Sivaji Babu ◽  
B. Uma Maheswar Gowd
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Cutting Speed ◽  
Fiber Composites ◽  
Fiber Reinforced Composites ◽  
Resin Matrix ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Composites

A study has been carried out to investigate the delamination and tensile properties of drilled composites made by reinforcing the natural fibers like hemp, jute, banana and vakka into a polyester resin matrix. The fibers extracted by retting and manual processes have been used to fabricate the composites. These composites are tested for delamination and tensile strength after drilling and compared with those of established composite like glass made under the same laboratory conditions. The Taguchi method with orthogonal array of L9 (34) was selected to realize the influence of the drilling parameters (cutting speed and feed rate) on delamination and tensile strength for various fiber reinforced composites. The results indicate that the delamination of the drilled natural fiber composites were in some cases better than those of glass fiber composites.

Processing of high weight fraction banana fiber reinforced epoxy composites using pressure induced dip casting method

2021 ◽  
pp. 002199832098804
Author(s):  
TP Mohan ◽  
K Kanny
Keyword(s):  
Matrix Composite ◽  
Epoxy Polymer ◽  
Epoxy Composite ◽  
Matrix Material ◽  
Natural Fibers ◽  
Weight Fraction ◽  
Polymer Composite Material ◽  
Fiber Reinforced ◽  
Banana Fiber ◽  
Banana Fibers

The objective of this work is to realize new polymer composite material containing high amount of natural fibers as a bio-based reinforcement phase. Short banana fiber is chosen as a reinforcement material and epoxy polymer as a matrix material. About 77 wt.% of banana fibers were reinforced in the epoxy polymer matrix composite, using pressure induced fiber dipping method. Nanoclay particles were infused into the banana fibers to improve the fiber matrix interface properties. The nanoclay infused banana fiber were used to reinforce epoxy composite and its properties were compared with untreated banana fiber reinforced epoxy composite and banana fiber reinforced epoxy filled with nanoclay matrix composite. The surface characteristics of these composites were examined by electron microscope and the result shows well dispersed fibers in epoxy matrix. Thermal (thermogravimetry analysis and dynamic mechanical analysis), mechanical (tensile and fiber pullout) and water barrier properties of these composites were examined and the result showed that the nanoclay infused banana fiber reinforced epoxy composite shows better and improved properties. Improved surface finish composite was also obtained by this processing technique.

Degradation Behaviour of Nanosilica Enhanced Oil Palm Empty Fruit Bunch Fiber Epoxy Composites

2020 ◽  
Vol 305 ◽  
pp. 28-35
Author(s):  
Anslem Wong Tsu An ◽  
Sujan Debnath ◽  
Vincent Lee Chieng Chen ◽  
Moola Mohan Reddy ◽  
Alokesh Pramanik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Palm ◽  
Environmental Conditions ◽  
Natural Fiber ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Empty Fruit Bunch ◽  
Degradation Behaviour ◽  
Brine Solution

In recent years, studies regarding natural fiber reinforced composites have been increased as they are biodegradable with good mechanical performance therefore can help to overcome the environmental issue. As the natural fibers are easy to obtain, many industries have started to make use of natural fiber composites which are light in weight and possess good mechanical properties. However, the natural fiber composites also possess certain limitations most importantly their high moisture absorption ability which makes them incompatible at degradable environment. The fiber constituents of natural fiber composite may have different type of interactions at different environmental conditions. In addition, the involvement of nanoparticles in the composite may be the solution to overcome the deficiencies. In this research, the degradation behaviour of Oil palm empty fruit bunch (OPEFB) fibers reinforced epoxy composites upon exposure to degradable environmental conditions and the effect of adding nanoparticles have been studied. The tensile tests were conducted before and after the exposure to different environmental conditions including plain water, moist soil, brine solution, and cooking oil. Results shows that the addition of 10wt% of OPEFB fiber to the epoxy composites had improved the mechanical tensile strength up to 15.97% and composites exposed to brine solution have the most prominent sign of degradation in mechanical properties in both composites with and without nanosilica. Nevertheless, the composites with nanosilica have shown up to 24.28% improvement in tensile strength after exposure to different environmental conditions. The improvement were attributed due to filling the voids of the composites with nanosilica and good interfacial adhesion between the nanofiller, fiber, and matrix.

Bacterial cellulose-natural fiber composites produced by fibers extracted from banana peel waste

2020 ◽  
pp. 152808372092584
Author(s):  
Muhammad Awais Naeem ◽  
Qasim Siddiqui ◽  
Muhammad Rafique Khan ◽  
Muhammad Mushtaq ◽  
Muhammad Wasim ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Banana Peel ◽  
Gravimetric Analysis ◽  
Natural Fiber Composites ◽  
Banana Fibers

In recent times, there is a growing demand for low-cost raw materials, renewable resources, and eco-friendly end products. Natural fibers are considered as strong candidates to be used as a potential reinforcement for composite manufacturing. In the current study, natural fibers extracted from banana peel were coated with bacterial cellulose through a green biosynthesis approach as well as by a simple slurry dipping method. Thus, natural fibers from banana peel waste were used the first time, to produce bacterial cellulose-natural fiber composites. SEM analysis revealed good interaction between the hybrid fibers and the epoxy matrix. Thermal gravimetric analysis results revealed that the degradation temperature increases because of the addition of bacterial cellulose on fiber surface, which improves the thermal stability. The maximum thermal decomposition temperature (405°C) was noticed for nanocomposites reinforced by banana fibers with bacterial cellulose deposited on their surface. Whereas the lowest weight loss was also found for the same sample group. The highest tensile strength (57.95 MPa) was found for SBC-BP/epoxy, followed by DBC-BP/epoxy (54.73 MPa) and NBP/epoxy (45.32 MPa) composites, respectively. Composites reinforced by both types of hybrid banana fibers shown comparatively higher tensile performance as compared with the neat banana peel fiber-epoxy composites, which can be attributed to the high strength and stiffness associated with the bacterial cellulose. Overall, this study suggests a successful and green route for the fabrication of natural fiber-reinforced composites with improved properties such as tensile strength and thermal stability.

Fabrication and Mechanical Properties of Banana Fiber Reinforced Biocomposite

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Surya Pratap Goutam ◽  
Rajkamal Shastri ◽  
J P Yadav ◽  
M K Gupta ◽  
Anil Kumar Yadav ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Renewable Resources ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Environmental Issues ◽  
Fiber Reinforced ◽  
Banana Fiber ◽  
Environment Friendly ◽  
Material Sources ◽  
Important Indication

<p>Usual polymer composites are non-biodegradable and pollute the environment. Using natural fibers with polymers<br />based on renewable resources will allow many environmental issues to be solved. Therefore, world is as of now focusing<br />on alternate material sources that are environment friendly and biodegradable in nature. Owing to increasing natural<br />concerns, bio composite produced out of natural fiber and polymeric resin, is one of the late advancements in the<br />scientific business. This paper is focused on fabrication and mechanical behaviour of natural fiber-reinforced<br />biocomposite R P E B . It is shown that a property of the fibers also gives important indication regarding their 15 15 40 30<br />subsequent behaviour as reinforcement in composites.</p>

Predicting the Best Flexural Strength of Banana-Bamboo-Glass Fiber Reinforced Natural Fiber Composites Using Taguchi Method

2015 ◽  
Vol 766-767 ◽  
pp. 162-166 ◽  
Author(s):  
Ashwin Sailesh ◽  
K. Palanikumar ◽  
R. Arunkumar ◽  
P. Ramu ◽  
A. Maxwell Briston ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Glass Fiber ◽  
Natural Fiber ◽  
Signal To Noise Ratio ◽  
Glass Fibers ◽  
Natural Fibers ◽  
Fiber Reinforced ◽  
Banana Fiber ◽  
Glass Fiber Reinforced ◽  
Day By Day

Over the past two to three decades the development in the field of composite material is immense and continues to be increasing. The utilization of natural fibers in the field of composites is increasing day by day. This is due the fact that natural fibers are eco-friendly, easily available, non-abrasive and economical. The combination of natural fiber with Glass fibers is finding increased applications. In the current investigation Banana – Bamboo – Glass fiber reinforced composites is fabricated by the method of Hand – Layup with variable fiber orientation and is tested for its flexural strength and the best flexural strength is identified by using Taguchi Methodology. Nomenclature Used: BN – Banana Fiber BM – Bamboo Fiber G – Glass fiber DOE – Design of Experiments S/N Ratio – Signal to Noise Ratio OA – Orthogonal Array.

scholarly journals Effects of Process Parameters on Tensile Strength of Jute Fiber Reinforced Thermoplastic Composites

1970 ◽  
Vol 3 (1) ◽  
pp. 1-6 ◽  
Author(s):  
HMMA Rashed ◽  
MA Islam ◽  
FB Rizvi
Keyword(s):  
Tensile Strength ◽  
Process Parameters ◽  
Natural Fiber ◽  
Environmental Concern ◽  
Research Work ◽  
Natural Fibers ◽  
Jute Fiber ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Ceramic Fibers

For Environmental concern on synthetic fibers (such as glass, carbon, ceramic fibers, etc.) natural fibers such as flax, hemp, jute, kenaf, etc. are widely used. In this research work, jute fiber reinforced polypropylene matrix composites have been developed by hot compression molding technique with varying process parameters, such as fiber condition (untreated and alkali treated), fiber sizes (1, 2 and 4 mm) and percentages (5%, 10% and 15% by weight). The developed jute fiber reinforced composites were then characterized by tensile test, optical and scanning electron microscopy. The results show that tensile strength increases with increase in the fiber size and fiber percentage; however, after a certain size and percentage, the tensile strength decreases again. Compared to untreated fiber, no significant change in tensile strength has been observed for treated jute fiber reinforcement. Fractographic observation suggests the fracture behavior to be brittle in nature. Keywords: Natural fiber, Jute fiber, Polypropylene, Composite, Tensile strength.  DOI: 10.3329/jname.v3i1.923 Journal of Naval Architecture and Marine Engineering 3(2006) 1-6

scholarly journals Mechanical Behaviour of Areca Nut, Sunn Hemp Natural Fibers and E-Glass Fibers Reinforced With Epoxy Composites

2019 ◽  
Vol 8 (6) ◽  
pp. 1092-1101 ◽  
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Automobile Industry ◽  
Natural Fiber ◽  
Glass Fibers ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Tensile Behaviour ◽  
Areca Nut ◽  
Sunn Hemp

In this paper, tensile behaviour of the natural fiber composites such as the areca nut composites and the sunn hemp composites were determined. The fibers were arranged in different orientations such as the uniaxial, biaxial and the criss-cross arrangements. For both the types of fiber composites, specimens were made with and without the incorporation of E-glass fibers. Comparisons were done on the basis of fiber orientation, E-glass fibers incorporation and the type of natural fiber used. Initially, the fibers were treated with alkali, i.e. Sodium hydroxide (NaOH) in order to get better bonding at the fiber-matrix interface. The conventional hand lay-up technique followed by the soft compression molding technique was carried out for fabricating the composite specimens. It was inferred from the results that the tensile strength was more for uniaxial arrangement and the least for biaxial arrangement in case of both the fibers. Further, for both the fibers, E-glass fiber incorporation increased the tensile strength as compared to the non-incorporated E-glass fiber composites. Also, sunn hemp composites showed better tensile strength than areca nut composites. The research suggested that the areca nut and sunn hemp composites were assets to many potential applications that did not require very high load bearing capabilities. These examined composites can be considered as very reliable materials for fabrication of lightweight materials used in automobile industry, packaging materials, medical field, etc.

Sign in / Sign up

Export Citation Format

Share Document