Characterization of Different Piezoelectric Profile for Energy Harvester

2015 ◽  
Vol 793 ◽  
pp. 407-411 ◽  
Author(s):  
Afifah Shuhada Rosmi ◽  
Syed Idris Syed Hasan ◽  
Y. Wahab ◽  
Mazlee Mazalan
Keyword(s):  
Energy Harvester ◽  
Electrical Power ◽  
Maximum Output Power ◽  
Mechanical Vibration ◽  
Electrical Potential ◽  
Low Frequency ◽  
Maximum Output ◽  
Excellent Performance ◽  
Microelectromechanical System

Microelectromechanical system (MEMS) piezoelectric transducer has been widely used as a mechanism for converting mechanical vibration into electrical power energy harvester.This paper presents a simulation result of cantilever-type piezoelectric MEMS generator with four different profiles to characterize the ability in producing a maximum output power at low frequency ambient vibration.Zinc Oxide is chosen as the piezoelectric material during the simulation. The simulation was conducted using IntelliSense’s CAE tool to obtain the natural frequency, electrical potential, and the optimum length dimension for each profile. The simulation result shows an excellent performance from trapezoidal shapetransducer with the electrical potential of 0.914 V at low frequency of 79.92 Hz.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

Broadband Low-Frequency Vibration Energy Harvester with a Rolling Mass

2013 ◽  
Vol 404 ◽  
pp. 635-639 ◽  
Author(s):  
Xue Feng He ◽  
You Zhu ◽  
Yao Qing Cheng ◽  
Jun Gao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvester ◽  
Low Frequency Vibration ◽  
Half Power

Richness of broadband low-frequency vibration energy in environemnts makes it significant to develop broadband low-frequency vibration energy harvesters. A vibration energy harvester composed of two symmetrical cantilevered piezoelectric bimorphs and a rolling mass in a guiding channel was proposed. A prototype of the vibration energy harvester with a rolling mass was assembled and tested. The base excitation caused the rolling mass to impact with two cantilevered bimorphs repeatedly and the impacts cause the bimorphs to vibrate dramatically. Experimental results show that maximum output power and corresponding excitation frequency increased with the amplitude of base acceleration. For the prototype, the maximum output power of a piezoelectric bimorph on a resistor with the resistance of 100 kΩ was 602 μW under base acceleration with the amplitude of 1.5 g and frequency of 37 Hz, and the half power bandwidth was about 13.5% or 5 Hz.

Characterization of microwave-sintered ceramic composites

1993 ◽  
Vol 51 ◽  
pp. 1136-1137
Author(s):  
X. Zhang ◽  
Y. Pan ◽  
T.T. Meek
Keyword(s):  
Matrix Material ◽  
Maximum Output Power ◽  
Ceramic Matrix Composite ◽  
Ceramic Composites ◽  
Processing Technique ◽  
Structure Characterization ◽  
Alumina Powder ◽  
Maximum Output ◽  
Sintered Ceramic

Industrial microwave heating technology has emerged as a new ceramic processing technique. The unique advantages of fast sintering, high density, and improved materials properties makes it superior in certain respects to other processing methods. This work presents the structure characterization of a microwave sintered ceramic matrix composite.Commercial α-alumina powder A-16 (Alcoa) is chosen as the matrix material, β-silicon carbide whiskers (Third Millennium Technologies, Inc.) are used as the reinforcing element. The green samples consisted of 90 vol% Al2O3 powder and 10 vol% ultrasonically-dispersed SiC whiskers. The powder mixture is blended together, and then uniaxially pressed into a cylindrical pellet under a pressure of 230 MPa, which yields a 52% green density. The sintering experiments are carried out using an industry microwave system (Gober, Model S6F) which generates microwave radiation at 2.45 GHz with a maximum output power of 6 kW. The composites are sintered at two different temperatures (1550°C and 1650°C) with various isothermal processing time intervals ranging from 10 to 20 min.

Liquid encapsulated electrostatic energy harvester for low-frequency vibrations

2012 ◽  
Vol 24 (1) ◽  
pp. 61-69 ◽  
Author(s):  
Ling Bu ◽  
Xiaoming Wu ◽  
Xiaohong Wang ◽  
Litian Liu
Keyword(s):  
Polyvinylidene Fluoride ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Electrostatic Energy ◽  
Maximum Output ◽  
Flowing Liquid ◽  
Horizontal Vibration ◽  
Low Viscosity ◽  
High Relative Permittivity

This article presents the modeling, fabrication, and testing of liquid encapsulated energy harvester using polyvinylidene fluoride electrets. Unlike harvesters reported in previous literature, this liquid encapsulated energy harvester uses flowing liquid rather than conventional resonating structures to induce variable capacitance and is more suitable for low-frequency applications. Prototypes injected with three types of liquid ( N-methyl-2-pyrrolidone, N, N-dimethylformamide, and glycerin) are tested in horizontal vibration and rotary motion mode, respectively. The results show that N, N-dimethylformamide–injected prototypes display the most desirable performance in horizontal vibration testing at 1–10 Hz due to high relative permittivity and low viscosity, with maximum output voltage of 2.32 V and power of 0.18 µW at 10 Hz. Glycerin-injected prototypes perform best at 0.1–1 Hz rotation due to effective movement and highest permittivity, with maximum output voltage of 11.46 V and power of 2.19 µW at 1 Hz.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals Study on the Efficiency and Dynamic Characteristics of an Energy Harvester Based on Flexible Structure Galloping

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6548
Author(s):  
Peng Liao ◽  
Jiyang Fu ◽  
Wenyong Ma ◽  
Yuan Cai ◽  
Yuncheng He
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Physical Model ◽  
Energy Harvester ◽  
High Efficiency ◽  
Lateral Displacement ◽  
Maximum Output Power ◽  
Flexible Structure ◽  
Maximum Output ◽  
Cfd Numerical Simulation

According to the engineering phenomenon of the galloping of ice-coated transmission lines at certain wind speeds, this paper proposes a novel type of energy harvester based on the galloping of a flexible structure. It uses the tension generated by the galloping structure to cause periodic strain on the piezoelectric cantilever beam, which is highly efficient for converting wind energy into electricity. On this basis, a physical model of fluid–structure interaction is established, and the Reynolds-averaged Navier–Stokes equation and SST K -ω turbulent model based on ANSYS Fluent are used to carry out a two-dimensional steady computational fluid dynamics (CFD) numerical simulation. First, the CFD technology under different grid densities and time steps is verified. CFD numerical simulation technology is used to simulate the physical model of the energy harvester, and the effect of wind speed on the lateral displacement and aerodynamic force of the flexible structure is analyzed. In addition, this paper also carries out a parameterized study on the influence of the harvester’s behavior, through the wind tunnel test, focusing on the voltage and electric power output efficiency. The harvester has a maximum output power of 119.7 μW/mm3 at the optimal resistance value of 200 KΩ at a wind speed of 10 m/s. The research results provide certain guidance for the design of a high-efficiency harvester with a square aerodynamic shape and a flexible bluff body.

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

scholarly journals Performance Evaluation of a Piezoelectric Energy Harvester Based on Flag-Flutter

Micromachines ◽  
2020 ◽  
Vol 11 (10) ◽  
pp. 933 ◽  
Author(s):  
Hassan Elahi ◽  
Marco Eugeni ◽  
Federico Fune ◽  
Luca Lampani ◽  
Franco Mastroddi ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Wind Tunnel ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Research Work ◽  
Maximum Output ◽  
Operational Environment ◽  
Subsonic Wind Tunnel ◽  
Piezoelectric Energy

In the last few decades, piezoelectric (PZT) materials have played a vital role in the aerospace industry because of their energy harvesting capability. PZT energy harvesters (PEH) absorb the energy from an operational environment and can transform it into useful energy to drive nano/micro-electronic components. In this research work, a PEH based on the flag-flutter mechanism is presented. This mechanism is based on fluid-structure interaction (FSI). The flag is subjected to the axial airflow in the subsonic wind tunnel. The performance evaluation of the harvester and aeroelastic analysis is investigated numerically and experimentally. A novel solution is presented to extract energy from Limit Cycle Oscillations (LCOs) phenomenon by means of PZT transduction. The PZT patch absorbs the flow-induced structural vibrations and transforms it into electrical energy. Furthermore, the optimal resistance and length of the flag is predicted to maximize the energy harvesting. Different configurations of flag i.e., with Aluminium (Al) patch and PZT patch for flutter mode vibration mode are studied numerically and experimentally. The bifurcation diagram is constructed for the experimental campaign for the flutter instability of a cantilevered flag in subsonic wind-tunnel. Moreover, the flutter boundary conditions are analysed for reduced critical velocity and frequency. The designed PZT energy harvester via flag-flutter mechanism is suitable for energy harvesting in aerospace engineering applications to drive wireless sensors. The maximum output power that can be generated from the designed harvester is 6.72 mW and the optimal resistance is predicted to be 0.33 MΩ.

Sign in / Sign up

Export Citation Format

Share Document