Research on Numerical Simulation of Support Interference for Dynamic Derivatives at Hypersonic Flight Speeds

2014 ◽  
Vol 1016 ◽  
pp. 495-500
Author(s):  
Xu Liu ◽  
Wei Liu ◽  
Yun Fei Zhao

The research on dynamic derivative under the dynamic unsteady condition is one of the most difficult aspects of the aircraft development process. For the special experiment of dynamic derivatives, no numerical simulation of support interference has yet been systematically studied. The numerical simulation of support interference for identification of dynamic derivatives with 7o blunted cone under the hypersonic condition was done in this paper. The 2-order Roe scheme and the dual-time-step method based on LU-SGS were respectively applied to discrete of the spatial and time derivative of the unsteady flow. A least square method based on the Etkin unsteady aerodynamic model was used for identification of dynamic derivatives. Hypersonic missile module was adopted as a verification example, and the numerical calculation results are consistent with the experimental results. For two different sting support forms with 7o blunted cone, the impact of sting support interference on dynamic derivatives was studied. Results show the moment coefficients of two support forms under static conditions are essentially the same, while there is a big difference in the pitch damping derivatives under dynamic conditions. The support interference of nonlinear aerodynamic loads resulted from the shock wave induced separation and other unsteady flow structures under dynamic conditions is far more complicated than that under static conditions, and the correction law of support interference under static conditions cannot be applied directly to the unsteady dynamic situations.

Author(s):  
Wei-Hong Zhang ◽  
Gang Tan ◽  
Min Wan ◽  
Tong Gao ◽  
David Hicham Bassir

In milling process, surface topography is a significant factor that affects directly the surface integrity and constitutes a supplement to the form error associated with the workpiece deformation. Based on the tool machining paths and the trajectory equation of the cutting edge relative to the workpiece, a new and general iterative algorithm is developed here for the numerical simulation of the machined surface topography in multiaxis ball-end milling. The influences of machining parameters such as the milling modes, cutter runout, cutter inclination direction, and inclination angle upon the topography and surface roughness values are studied in detail. Compared with existing methods, the basic advantages and novelties of the proposed method can be resumed below. First, it is unnecessary to discretize the cutting edge and tool feed motion and rotation motion. Second, influences of cutting modes and cutter inclinations are studied systematically and explicitly for the first time. The generality of the algorithm makes it possible to calculate the pointwise topography value on any sculptured surface of the workpiece. Besides, the proposed method is proved to be more efficient in saving computing time than the time step method that is commonly used. Finally, some examples are presented and simulation results are compared with experimental ones.


Author(s):  
Mohammad Amin Nabian ◽  
Leila Farhadi

A mesh-less numerical approach, called the moving particle semi implicit method (MPS), is presented to solve inviscid Navier-Stokes equations in a fully Lagrangian form using a fractional step method. This method consists of splitting each time step in two steps. The fluid is represented with particles and the motion of each particle is calculated through interactions with neighboring particles by means of a kernel function. In this paper, the MPS method is used to simulate a dynamic system consisting of a heavy box sinking vertically into a water tank, known as Scott Russell’s wave generator problem. This problem is an example of a falling rock avalanche into natural or artificial reservoirs. The box sinks into water tank and as a result the water is heaved up to form a solitary wave and a reverse plunging wave which forms a vortex. This vortex follows the solitary wave down the water tank. The good agreement between the numerical simulation and the analytical solution confirms the accuracy of the model. This proves the applicability of the present model in simulating complex free surface problems. The number of particles on free surface is presented as an indicator of stability of the model.


Author(s):  
Yu Lu ◽  
Ankang Hu ◽  
Xin Chang

The main focus of this paper is on the uncertainty analysis methodology and procedure in CFD recommended by 22nd ITTC and the benchmark database for the verification and validation of the results of dredging dustpan’s inlet and outlet cross-section velocity ratio coefficient viur. Compared with the previous uncertainty analysis of CFD focused on the fluid grid-convergence in the steady flow, which is less to consider other factors that may affect the accuracy of the results of numerical simulation, this study compensates for this deficiency and implements the grid-convergence and time-step-size-convergence studies respectively by using three types of grids and time step sizes with refinement ratio under the condition of unsteady flow. Through confirming the validity of CFD uncertainty analysis, the agreement between the numerical simulation correction values from the grid-convergence and time-step-size-convergence and the benchmark test data is found to be quite satisfactory. The results obtained in this study have shown that it is indispensable to carry out the time-step-size-convergence studies for CFD uncertainty analysis during the unsteady flow calculation because the numerical simulation errors respectively caused by the grid and time-step-size in the convergence study have the same order of magnitude. In further the present study of simultaneously conducting both grid-convergence and time-step-size-convergence is demonstrated efficient and effective in the CFD uncertainty analysis.


Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1945 ◽  
Author(s):  
Salem Basfar ◽  
Abdelmjeed Mohamed ◽  
Salaheldin Elkatatny ◽  
Abdulaziz Al-Majed

Barite sag is a serious problem encountered while drilling high-pressure/high-temperature (HPHT) wells. It occurs when barite particles separate from the base fluid leading to variations in drilling fluid density that may cause a serious well control issue. However, it occurs in vertical and inclined wells under both static and dynamic conditions. This study introduces a combined barite–ilmenite weighting material to prevent the barite sag problem in water-based drilling fluid. Different drilling fluid samples were prepared by adding different percentages of ilmenite (25, 50, and 75 wt.% from the total weight of the weighting agent) to the base drilling fluid (barite-weighted). Sag tendency of the drilling fluid samples was evaluated under static and dynamic conditions to determine the optimum concentration of ilmenite which was required to prevent the sag issue. A static sag test was conducted under both vertical and inclined conditions. The effect of adding ilmenite to the drilling fluid was evaluated by measuring fluid density and pH at room temperature, and rheological properties at 120 °F and 250 °F. Moreover, a filtration test was performed at 250 °F to study the impact of adding ilmenite on the drilling fluid filtration performance and sealing properties of the formed filter cake. The results of this study showed that adding ilmenite to barite-weighted drilling fluid increased fluid density and slightly reduced the pH within the acceptable pH range (9–11). Ilmenite maintained the rheology of the drilling fluid with a minimal drop in rheological properties due to the HPHT conditions, while a significant drop was observed for the base fluid (without ilmenite). Adding ilmenite to the base drilling fluid significantly reduced sag factor and 50 wt.% ilmenite was adequate to prevent solids sag in both dynamic and static conditions with sag factors of 0.33 and 0.51, respectively. Moreover, HPHT filtration results showed that adding ilmenite had no impact on filtration performance of the drilling fluid. The findings of this study show that the combined barite–ilmenite weighting material can be a good solution to prevent solids sag issues in water-based fluids; thus, drilling HPHT wells with such fluids would be safe and effective.


2018 ◽  
Vol 192 ◽  
pp. 02030
Author(s):  
Sodsai Lamtharn ◽  
Monsak Pimsarn

Numerical simulation of two-dimensional laminar unsteady flow past a right trapezoidal cylinder at low Reynolds number (Re = 100), zero of the flow approaching angle and sharpening angle of the right trapezoidal of 22.5° with a side ratio B/A = 1 are carried out to provide moreapplicable data for engineering design of barred tee in aspect of structural integrity. A finite volume method, non-uniform meshing with second-order implicit time discretization into eight-node quadratic quadrilateral finite elements is employed. An incompressible flow SIMPLEC code with constant fluid properties is used. The convective terms using a third-order QUICK scheme. The numerical simulation result is compared against the published results of flow past a square cylinder. The effect of sharpening angle on the response of the right trapezoidal cylinder is investigated. A special study of the effects of flow on significant factor for time step, grid independence, blockage ratio, domain size, upstream and downstream extents, size domain next to cylinder and size domain extent are performed systematically. The Strouhal number and RMS lift coefficients of fully saturated flow are calculated. The result shown that increasing of sharpening angle, the Strouhal number is negligible changed whilst the RMS lift coefficients significantly increased.


2008 ◽  
Vol 575-578 ◽  
pp. 104-108
Author(s):  
Jie Yang ◽  
Yu Xin Ren ◽  
Shou Mei Xiong

In the numerical simulation of mold filling process, the calculation efficiency has been a key point for practical applications due to the complexity and thin-section of die castings. In current research work, a fractional step method was applied in the solution of the unsteady Navier-Stokes equations, which can be implemented with a single solution to the momentum/pressure equations at each time step. This method may avoid the decrease in efficiency induced by iteration. A water analog system was designed and developed to simulate the die casting process. The flow patterns were recorded by a high speed camera with a capturing rate of 500 frames per second. The simulation results were consistent with the experimental ones. Besides, the fluid flow patterns of several components were simulated by the fractional step and VOF algorithm, and the SOLA-VOF algorithm respectively. The simulation results showed that the combination of the fractional step method and VOF method can improve the computational efficiency to some extent in numerical simulation of mold filling process.


Blood ◽  
2011 ◽  
Vol 118 (21) ◽  
pp. 2199-2199 ◽  
Author(s):  
Marianna Gyenes ◽  
Markus Hasse ◽  
Volker R. Stoldt ◽  
Abdelouahid El-Khattouti ◽  
Khon C. Huynh ◽  
...  

Abstract Abstract 2199 Objectives: Platelet integrin αIIbβ3 is polymorphic at residue 33 (Leu33/HPA-1a or Pro33/HPA-1b). In patients with coronary artery disease, the Pro33 isoform is associated with premature manifestation of myocardial infarction (Zotz et al., JTH 2005). Based on this finding, it has been postulated that the Pro33 variant of αIIbβ3 has a prothrombotic phenotype. Moreover, several studies have shown that elevated shear stress can activate platelets leading to shear-induced platelet aggregation contributing to acute myocardial infarction. Thus, it has been reported that pathological shear stress directly regulates αIIbβ3 (Feng et al., Am J Physiol Cell Physiol 2006). We have shown that adherent Pro33 platelets have a higher resistance than Leu33 platelets upon exposure to high shear rates (Loncar et al, Thromb J 2007). We now studied the impact of the Leu33/Pro33 polymorphism on αIIbβ3-mediated outside-in signaling under static and flow dynamic conditions in the presence or absence of Mn2+, analyzing the Src pY418 and FAK pY397 activities. Methods: Adhesion assays were performed with 10 or 100 μg/ml of immobilized fibrinogen for different incubation times with washed human platelets in the presence or absence of Mn2+ (0.5 mM). Mn2+ induces the active conformation of αIIbβ3. Src pY418 and FAK pY397 activities were determined by Western blotting and quantified densitometrically. Control experiments were performed with 1% BSA. Adhesion experiments under flow conditions were carried out with a cone-plate viscometer. Results: Under static conditions, Pro33 platelets adherent onto fibrinogen exhibited a 2.5-fold higher Src pY418 activity than Leu33 platelets after incubation for 20 min (p<0.01). Presence of Mn2+ (0.5 mM) in suspended Leu33 platelets stimulated their Src pY418 activity in an extent comparable to that of platelets adherent onto fibrinogen, while addition of Mn2+ (0.5 mM) to platelets adherent onto fibrinogen yielded a 3.5-fold increase in Src pY418 activity (p<0.05). Increase of the Mn2+ concentration (2 mM) raised the Src pY418 activity 1.5-fold, as compared to 0.5 mM Mn2+ (p<0.05). In parallel experiments with both HPA-1 isoforms of αIIbβ3, Pro33 platelets adherent onto fibrinogen in the presence of 0.5 mM Mn2+ revealed a 2.5-fold higher Src pY418 activity than Leu33 platelets after 5 min (p<0.05). This difference further increased upon prolonged adhesion for 10 or 20 min with a 5-fold increase after 40 min (p<0.01). The concentration of immobilized fibrinogen (10 or 100 μg/ml) had no influence on this effect. Addition of abciximab completely abolished the Src pY418 activation. Upon exposure to abnormal (5000 s−1) but not physiological (500 s−1) shear rates for 2 or 5 min, Pro33 platelets adherent onto 100 μg/ml fibrinogen exhibited a 2- or 2.5-fold higher Src pY418 activity than under static conditions (p<0.05 or 0.02, respectively). Under the same conditions, the Src pY418 activity of Pro33 platelets was 2-fold higher than that of Leu33 platelets (p<0.05). Again, different concentrations of fibrinogen (10 μg/ml and 100 μg/ml) did not affect these results. In comparison to Src (pY418), phosphorylation of FAK (pY397) increased slower both in Leu33 and Pro33 platelets adherent onto fibrinogen, when exposed to a shear rate of 5000 s−1 for 10min. Both isoforms (Leu33 or Pro33) exhibited a significantly higher FAK pY397 activity than under static conditions (3-fold increase, p<0.05). The Pro33 variant of αIIbβ3 showed a higher FAK pY397 activation than the Leu33 isoform (p<0.05). Again, abciximab completely blocked both the Src and FAK activation not only under static conditions but also upon exposure to shear. Conclusion: Our observations indicate that the HPA-1 polymorphism of αIIbβ3 has a considerable impact on the integrin-mediated outside-in signaling. The significantly higher Src (pY418) and FAK (pY397) activities of Pro33 platelets adherent onto fibrinogen under static and flow conditions are in agreement with the contention that the Pro33 (HPA-1b) isoform of αIIbβ3 is indeed a prothrombotic integrin variant. Disclosures: No relevant conflicts of interest to declare.


2019 ◽  
Vol 11 (20) ◽  
pp. 5617 ◽  
Author(s):  
Abdelmjeed Mohamed ◽  
Salem Basfar ◽  
Salaheldin Elkatatny ◽  
Abdulaziz Al-Majed

Drilling high-pressure high-temperature (HPHT) wells requires a special fluid formulation that is capable of controlling the high pressure and is stable under the high downhole temperature. Barite-weighted fluids are common for such purpose because of the good properties of barite, its low cost, and its availability. However, solids settlement is a major problem encountered with this type of fluids, especially at elevated downhole temperatures. This phenomenon is known as barite sag, and it is encountered in vertical and directional wells under static or dynamic conditions leading to serious well control issues. This study aims to evaluate the use of barite-ilmenite mixture as a weighting agent to prevent solids sag in oil-based muds at elevated temperatures. Sag test was conducted under static conditions (vertical and inclined) at 350 °F and under dynamic conditions at 120 °F to determine the optimum ilmenite concentration. Afterward, a complete evaluation of the drilling fluid was performed by monitoring density, electrical stability, rheological and viscoelastic properties, and filtration performance to study the impact of adding ilmenite on drilling fluid performance. The results of this study showed that adding ilmenite reduces sag tendency, and only 40 wt.% ilmenite (from the total weighting material) was adequate to eliminate barite sag under both static and dynamic conditions with a sag factor of around 0.51. Adding ilmenite enhanced the rheological and viscoelastic properties and the suspension of solid particles in the drilling fluid, which confirmed sag test results. Adding ilmenite slightly increased the density of the drilling fluid, with a slight decrease in the electrical stability within the acceptable range of field applications. Moreover, a minor improvement in the filtration performance of the drilling fluid and filter cake sealing properties was observed with the combined weighting agent. The findings of this study provide a practical solution to the barite sag issue in oil-based fluids using a combination of barite and ilmenite powder as a weighting agent to drill HPHT oil and gas wells safely and efficiently with such type of fluids.


Aerospace ◽  
2021 ◽  
Vol 8 (12) ◽  
pp. 373
Author(s):  
Hao Dai ◽  
Chengxiang Zhu ◽  
Ning Zhao ◽  
Chunling Zhu ◽  
Yufei Cai

An unsteady tightly-coupled icing model is established in this paper to solve the numerical simulation problem of unsteady aircraft icing. The multi-media fluid of air and droplets is regarded as a single medium fluid with variable material properties. Taking the droplet concentration as the phase parameter and the droplet resistance coefficient as the interphase force, the mass concentration distribution of the droplet is obtained by solving the Cahn–Hilliard equation. Fick’s law is introduced to improve the Cahn–Hilliard equation to predict the droplet shadow zone. On this basis, the procedure of the unsteady numerical simulation method for aircraft icing is established, including grid generation, the dual-time-step method to realize the unsteady calculation of the air and droplet tightly-coupled mixed flow field, and the improved shallow water icing model. Finally, through the comparative analysis of numerical examples, the effectiveness of the new model in predicting the droplet impact characteristics and the droplet shadow zone are verified. Compared with other icing models, the ice shapes predicted by the unsteady tightly-coupled model were found to be the most consistent with the experiments. In the icing comparison conditions in this manuscript, the prediction accuracy of the ice thickness at the stagnation point of the leading edge was up to 35% higher than that of LEWICE.


2017 ◽  
Vol 20 (8) ◽  
pp. 915-917 ◽  
Author(s):  
Ana Fenández-Tena ◽  
Alfonso C. Marcos ◽  
Cristina Martínez ◽  
D. Keith Walters

Sign in / Sign up

Export Citation Format

Share Document